Requests for wood wax oil recipes and production, there must be a heavy thanks

Wood wax oil formula:

1. Wind blowing polymerized linseed oil (carnauba wax (beeswax (dama resin (shellac (citrus oil d-limonene (anhydrous alcohol (.

2. Wind blowing polymerized flaxseed oil (wind blowing polymerized rapeseed oil (wind blowing polymerized soybean oil (hand wax (carnauba wax (beeswax (dama resin (shellac (citrus oil d-limonene (anhydrous alcohol (. Serious attention, close warning:

1. It is not recommended to use turpentine as a thinner, the use of wood wax oil is for environmental protection and health, although turpentine is also a natural product, but its chemical composition and properties are harmful to the human body (natural is not necessarily environmentally friendly).

2. It is not recommended to use carnauba wax, which is Sichuan wax, which can replace carnauba wax in terms of performance, but it is higher than carnauba wax and is not economical.

3. It is not recommended to use Marty resin, ** is almost ten times that of Dama resin, and the economy is not strong.

4. It is not recommended to use ordinary flax oil and other oils, and unmodified oils cannot be used as furniture coatings.

5. It is not recommended to use Wuliangye, ** is almost 100 times that of anhydrous alcohol, although the taste is good, but the economy is too poor, haha.

6. It is recommended to use citrus oil (D-limonene) as a thinner, which is pure natural and environmentally friendly, harmless to the body, and smells good. 7. It is recommended to use wind-blown polymerized linseed oil as the main component of homemade wood wax oil.

8. It is recommended to use silicone modified wax paste, which is better than using carnauba wax in terms of performance and perception.

If you want to engage in production, if you have a sample that you are satisfied with, we can help you determine the proportion of each ingredient through microscopic analysis, carry out formula restoration, and then provide corresponding raw material recommendations and technical support in the later stage. What a Lian system?

Wood wax oil. Choose turpentine.

or wood wax oil thinner.

Dilution, both of which work very well. Wood wax reed oil is a natural plant-derived wipe, this kind of thing contains a high degree of wax and vegetable resin, the viscosity is thick, when actually used, it needs to be diluted.

in a high-temperature environment.

Wax oil or wood oil brushes will blister on the surface of the wood, and it is necessary to add a hygroscopic agent at this time, which can also slow down the occurrence of this situation.

The thinner of wood wax oil has a strong taste, high formaldehyde content, and great harm, so it is not very suitable for interior decoration or solid wood furniture.

The use of the burial respect.

The supporting thinner of wood wax oil will generally taste very light, and the environmental protection line is higher than the traditional thinner, and during construction, the green environmental protection products that do not destroy the fresh environment of furniture need to be specially used for wood wax oil and wood oil for dilution.

There is generally no fixed proportion of thinner, and it can be diluted according to your actual situation when you use it, so that the wood wax oil will not be too thick.

If you really don't know how to proportion, you can only test the ratio of a barrel of wood wax oil to a bottle of 500ml thinner at this time, and the effect is still very good.

How to use:

Substrate treatment: The moisture content of the wood is not more than 20%.

Sanding: Sanding the wood with sandpaper until the surface is smooth and smooth. Sandpaper should be used in order from small to large, and the larger the number of sandpaper meshes, the more delicate the grinding effect. The finer and smoother the wood surface, the better the effect of wood wax oil, and the more economical wood wax oil is.

Hole filling treatment: repair the nail holes and knotted scar holes with transparent or putty of the same color to be smooth.

Cleaning treatment: Make the surface clean and dry before painting, free of grease and dust.

Operating instructions: Stirring: Stir well after opening the can until it is even.

Brushing: Use cotton cloth, hard brush, roller and other tools to evenly extend the paint in the direction of the wood texture, after slightly drying, if there is uneven paint on the surface, wipe off with a clean cotton cloth to make the surface of the coated wood smooth.

Apply directly, no primer, no dilution, stir evenly, and brush once or twice.

Note: Cherexi furniture series wood wax oil, due to different climates and environments, the viscosity will be different, please use with Cherexi deodorant thinner, and the appropriate construction viscosity has been adjusted to achieve the construction effect.

Steps: Step 1: Substrate Treatment.

The substrate is generally sanded with 100 grit paper until it is smooth and flat.

Thoroughly remove the sanding dust and confirm that the surface to be coated is clean, dry and free of grease and dust.

Step 2: Thin the first pass.

Open the wood wax oil and stir well (you can add an appropriate amount of Cheresib deodorant thinner), dip an appropriate amount of wood wax oil with a cotton cloth, wipe it along the direction of the wood grain, make sure that all the surface layers have been wiped, and use a clean cotton cloth to clean the excess oil on the surface to ensure that there is no excess oil on the surface.

Step 3: Polishing.

Wait for the first time to dry completely, about 4 6 hours or more, and rub it with Cheresi special polishing cotton or sandpaper of more than 600 meters.

The surface layer of wood wax oil is lightly sanded and polished, and the sanding dust is completely removed.

Step 4: Rub it a second time.

Please wipe it again according to the process requirements, generally wipe it 2 or 3 times, and please follow the third step for slight polishing between the thin wipe and the thin rub.

Step 5: Polishing.

After all the construction steps are completed, use more than 1000 sandpaper or special polishing cotton for Cheresi to lightly carry out the surface layer.

Polishing, and clean the surface sanding dust to enhance the feel.

The method of application of wood wax oil includes the preparation of tools and materials, as well as the cleaning of the application.

1. Prepare tools and materials.

You need to prepare the required tools and materials before construction, including wood wax oil, sandpaper, brushes, cloths, clean work clothes and gloves, etc. The surface of the wood needs to be cleaned, sandpaper is used to smooth the surface so that the wood wax oil can better adhere to the wood surface. If there are stubborn stains or grease, you can wipe them clean with a mild detergent or alcohol.

2. Apply wood wax oil.

Pour an appropriate amount of wood wax oil into a container and spread evenly on the surface of the wood with a brush. It is recommended to apply from top to bottom to avoid dripping or missing application. Care should be taken not to overapply when applying, otherwise it will affect the drying time and effect.

After applying the wax oil, you need to wait for some time for it to dry naturally. Depending on the ambient temperature and humidity, the drying time will vary.

Matters needing attention in the construction of wood wax oil

1. Wood surface treatment: Before construction, the wood surface needs to be fully treated. First of all, dust and dirt are removed from the surface of the wood, and the surface of the wood is sanded with sandpaper so that the paint can be better absorbed.

Secondly, if there are cracks or depressions in the surface of the wood, these defects need to be filled first. Finally, make sure that the surface of the wood is dry, clean and flat.

2. Choose the right tools and materials: In the construction process, you need to choose the right tools and materials. For example, tools such as brushes, rollers, etc., need to be used to apply wood wax oil. In addition, it is necessary to prepare sufficient coatings and thinners, and ensure that the quality of these materials is reliable.

3. Pay attention to the thickness and uniformity of the coating: During construction, it is necessary to pay attention to the thickness and uniformity of the coating. If the paint is too thick, it will affect the texture and appearance of the wood surface; If the coating is uneven, it can lead to problems such as blistering or sagging.

Therefore, it is necessary to control the thickness and uniformity of the coating to ensure the quality of the coating.