Does anyone know the mix ratio of epoxy cement and the amount per square meter, thank you

The example is as follows: <>

One of the epoxy flooring coatings is epoxy resin.

Composed of ethylenediamine curing agent, adding epoxy filler, epoxy cement is widely used in epoxy flooring coating, putty.

as well as the repair and surface treatment of buildings, metal structures, etc.

1. The mix ratio of epoxy mortar and epoxy base liquid is mass ratio, unit g

2. Material name: epoxy resin, ethylenediamine (curing agent), dibutyl (toughening agent), acetone (diluent.

3. Preparation process of epoxy base solution: epoxy resin is added with dibutyl and acetone and mixed well, and then ethylenediamine is added and mixed well;

4. Epoxy mortar preparation process: epoxy resin is added to dibutyl and acetone and mixed well, then ethylenediamine is added and mixed well, and finally the cement and sand filler preheated to 30 is added and mixed well (the amount of propylene copper and cement can be increased or decreased appropriately);

5. If the epoxy resin is thicker, it can be heated to more than 50 and then add dibutyl and acetone and mix well;

6. The sand used in epoxy mortar must be anhydrous dry sand (it can be heated in a wok to remove water, and the heating temperature is not less than 30, until the sand is dried), and it must be sieved with a 5mm sieve;

7. When cooperating, it is necessary to accurately measure with measuring tools, and after ethylenediamine is added, construct as soon as possible, and control the mixing products to be used up within 45min to prevent epoxy consolidation (the amount of ethylenediamine can be increased or decreased appropriately);

8. Each mix ratio is tried to mix once, and then mixed in large quantities, but the amount of mixing is not easy to be too much, and it shall be used up within 20 minutes (the weight shall not exceed when repairing small defects;

9. When mixing ethylenediamine and acetone, avoid contact with **;

10. The base surface of the repair part must be dry before the epoxy mortar can be smeared to prevent the poor bonding caused by the wetness of the base surface and cracks at the joint surface;

11. When slotting, the groove boundary must be cut with a cutting machine to cut a seam with a depth of about 2cm or more and then chisel the groove;

12. Epoxy mortar must be flush with the structural surface when filling the groove.

Hello· The mix ratio of epoxy cement is · 1: Because epoxy resin is expensive· So a little more powder is also okay· The dosage per square is 25 kg per square centimeter If you are using granite or something like that· It depends on the weight of the granite· How much is it· Generally 5 cm thick granite · Paste and apply the cement should be about 17 kg per square · If it's heavier · Just use more· Hope it helps you for more details. For details, you can consult Jiaozuo Shuotong anticorrosive material**** They are a professional cement manufacturer· Quality assurance.

The mix ratio of epoxy cement is: epoxy resin: ethylenediamine: quartz powder = 1::2

For example, epoxy flooring is a kind of coating, which is composed of epoxy resin and ethylenediamine curing agent, adding epoxy filler, epoxy cement is widely used in epoxy flooring, putty, as well as buildings, metal structure repair and surface treatment, etc.

1. The mix ratio of epoxy mortar and epoxy base liquid is mass ratio, unit g

2. Material name: epoxy resin, ethylenediamine (curing agent), dibutyl (toughening agent), acetone (diluent.

3. Preparation process of epoxy base solution: epoxy resin is added with dibutyl and acetone and mixed well, and then ethylenediamine is added and mixed well;

4. Epoxy mortar preparation process: epoxy resin is added to dibutyl and acetone and mixed well, then ethylenediamine is added and mixed well, and finally the cement and sand filler preheated to 30 is added and mixed well (the amount of propylene copper and cement can be increased or decreased appropriately);

5. If the epoxy resin is thicker, it can be heated to more than 50 and then add dibutyl and acetone and mix well;

6. The sand used in epoxy mortar must be anhydrous dry sand (can be heated in a wok to remove water, the heating temperature is not less than 30, and the sand is dried in the shed), and it must be sieved with a 5mm sieve;

7. When cooperating, it is necessary to accurately measure with measuring tools, and after ethylenediamine is added, construct as soon as possible, and control the mixing products to be used up within 45min to prevent epoxy consolidation (the amount of ethylenediamine can be increased or decreased appropriately);

8. Each mix ratio is tried to mix once, and then mixed in large quantities, but the amount of mixing is not easy to be too much, and it shall be used up within 20 minutes (the weight shall not exceed when repairing small defects;

9. When mixing ethylenediamine and acetone, avoid contact with **;

10. The base surface of the repair part must be dry before the epoxy mortar can be wiped to prevent the socks and the seller from being wet on the base surface, causing poor bonding and cracks at the joint surface;

11. When tease and groove, the groove boundary must be cut into a gap of about 2cm or more by a cutting machine and then chiseled the groove;

12. Epoxy mortar must be flush with the structural surface when filling the groove.

Summary. Hello dear, the proportional processing methods of epoxy cement include: 1

Choose the right epoxy cement; 2.Accurate dosing of ingredients in proportion; 3.Mix well; 4.

Processing according to the requirements of use; 5.Analyze the quality and control the quality.

Hello dear, the proportional processing methods of epoxy cement include: 1Choose the annular cherry oxide cement suitable for the vertical bond; 2.

Accurate dosing of ingredients in proportion; Large Fiber Plexus 3Mix well; 4.Processing according to the requirements of use; 5.

Analyze the quality and control the quality.

Hello, the proportion of epoxy cement is calculated according to the proportion of epoxy resin, fly ash or lime, quartz sand and water, and the specific proportion can be adjusted according to the actual use requirements.

Hello, epoxy cement is a polymer material, composed of epoxy resin, fly ash or lime, quartz sand and water, which can be used to make waterproof car side layers, decoration, heat preservation, heat insulation and acoustic sound absorption sail burning of various buildings. The material has excellent waterproof, wear-resistant, freeze-thaw resistance, acid and alkali resistance and other characteristics.

Hello, the ratio of epoxy cement is generally calculated according to 100 parts of epoxy resin: 30 parts of fly ash or lime: 50 parts of quartz hall grit: 20 parts of water. However, when it is actually used or used violently, it should be adjusted according to the actual requirements to get better results.