What should I do if the seat of the reflector on the motorcycle is broken?

Add an ordinary five-sheep single-lens seat to the direction tube in front of the disc brake pump, and install the reflector separately, and you can get it for a few dollars.

Go to the place where the motorcycle is repaired and change a pair of rearview mirrors, about 20 yuan to 60 yuan.

How to adjust the loose ball joint of the motorcycle rearview mirror:

1. First take the wrench, unscrew the screws on the rearview mirror first, and let the screws loose.

2. Hold the rearview mirror with your hand and rotate it counterclockwise until the rearview mirror exits.

3. Put the rotating rearview mirror on the ground, check the damage of the rearview mirror, if the small problem can be remedied, the big problem should be replaced with a new one.

4. Open the plastic bag of the motorcycle rearview mirror you bought, insert it into the rearview mirror hole slot, and then rotate it clockwise.

5. Adjust the angle of the rearview mirror, use a wrench, and lock the screws on the rearview mirror.

Precautions when driving:

1.Drive on the right-hand side of the road, not on the sidewalk.

2.Do not get too close to the car, but follow the right rear corner of the car in front and keep an appropriate distance.

3.When overtaking, you should overtake on the left side in front of you, overtake on the right side or between two parallel cars.

4.Reduce sudden acceleration and sudden stops to prevent emergencies.

5.Be sure to slow down when turning, as it is easy to lose your balance if you go too fast.

6.In rainy days, the friction resistance on the ground is small, and the braking distance is relatively long, so you must slow down and drive slowly.

7.When driving at night, you must slow down due to the short visual distance.

8.If you feel that there is something abnormal on your motorcycle while driving, you must stop for inspection.

9.Do not race with a car.

10.Drive safely according to traffic laws and give way to pedestrians.

This is a very common clutch handle assembly, many cars are universal, generally change a set of assembly ** is about 30 50 yuan, go to the after-sales or repair of the motorcycle place to buy a replacement on the line.

Two methods:

1. Replace the bracket below, generally as long as there is a specific model, you can buy accessories to replace. Just ask the repair shop.

2. Punch holes directly, then put threads, and install the rearview mirror, which requires you to have hands-on ability.

There are places to repair motorcycles, ranging from 20 to 30.

This motorcycle reflector is locked and fixed by the nut at the bottom of the mirror shaft, use a suitable open-end wrench (see the open-end wrench in the picture should be 14) to loosen the lock nut counterclockwise, and then unscrew the mirror counterclockwise to replace it, and then screw on the new mirror in reverse order, and finally tighten the lock nut.

You can unscrew it by hand and turn it in a counterclockwise direction.

1. Use a wrench to unscrew the screws on the rearview mirror.

2. Hold the mirror with your hand and rotate it counterclockwise until the mirror exits.

3. Get a new pair of mirrors.

4. Insert the rearview mirror hole slot, and then rotate clockwise until the screws are tightened.

5. Adjust the angle of the rearview mirror and lock the screws on the rearview mirror.

The one below is the one that goes in with the reverse silk, as long as you unscrew it off in reverse.

Put the one on top is a round joint, and there is a screw on the back, and loosen the screw, and he will be able to take it off.

Summary. Hello dear, <>

If my answer is helpful to you, please give a thumbs up (in the bottom left corner), I look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress. If you feel that my answer is still satisfactory, you can click on my avatar for one-on-one consultation. Finally, I wish you good health and a good mood!

<> when the reflector is removed from the women's motorcycle, the iron rod of the reflector is broken on the faucet handle bracket due to rust, how to find a way to dismantle it.

Please wait patiently for a few minutes, it is being sorted out, and we will answer you immediately.

Hello dear<>

Glad for your question When the women's motorcycle vertical orange car dismantles the reflector, the reflector iron rod is broken on the faucet bracket due to rust, how to find a way to disassemble the pro You can use a drilling machine to make a hole and then use the vertical screw to remove the remaining fiber group.

Hello dear, <>

If my answer is helpful to you, please also give a thumbs up (comment in the lower left corner), look forward to your wide concession and praise, your efforts are very important to me, and your support is also the driving force for my progress. If you feel that I am still satisfied with my answer, you can click on my avatar for one-on-one consultation. Finally, I wish you good health and a good mood!

Question 1: How can I get the Yamaha Curved Beam motorcycle reflective lenses off?100w per resource

Question 2: How to remove the lens of the motorcycle rearview mirror and soak it in the water.

Question 3: How to remove the scooter reflector?This motorcycle reflector is locked and fixed by the nut at the bottom of the mirror shaft, use a suitable open-end wrench (see the open-end wrench in the picture should be 14) to loosen the lock nut counterclockwise, and then unscrew the mirror counterclockwise to replace it, and then screw the new mirror nail in reverse order and finally tighten the lock nut.

Question 4: How to remove the motorcycle rearview lens The rearview mirror of the motorcycle is fixed by screws, and the rearview mirror can be removed by loosening or removing the screws with a suitable open-end wrench or hexagon wrench.

Question 5: How to disassemble the motorcycle reflector? turned.

You can get rid of it with just a lot of effort.

Question 6: How to disassemble the reversing mirror of the motorcycle disposable.

Question 7: How to remove the motorcycle clutch switch from the reflector The protrusions on both sides of the red mark are the fixed points When dismantling, use a sharp thing in the hall to top it.

Question 9: How to disassemble the mirror of a motorcycle Different cars do not wear the same Especially Yamaha's.

Summary. Hello, the specific analysis is as follows.

1. Micro scratches First aid products: fine wax, coarse wax The paint damage caused by slight scratches is on the surface of the topcoat and can be completely repaired by waxing. Treated with a mixture, the wiping method is a straight line wipe, and then wax, you can use coarse wax first, and then fine wax, from the inside to the outside in the same direction, so that the fine scratches are almost removed.

Of course, there is a more cost-effective way to repair it with toothpaste, gently apply it to the shallow scratches, and then rub it counterclockwise with a soft cotton cloth to not only reduce the scratches, but also avoid the erosion of the air on the paint wounds.

How to repair a piece of the scooter reflector handle.

Hello, the specific analysis is as follows.

1. Micro scratches First aid products: fine wax, coarse wax Slightly scratched paint damage is on the surface of the topcoat and can be completely repaired by waxing. Treated with a mixture, the wiping method is a straight line wipe, and then wax, you can use coarse wax first, and then fine wax, from the inside to the outside in the same direction, so that the fine scratches are almost removed.

Of course, there is a more cost-effective way to repair Sun Minfu with toothpaste, lightly apply it to the shallow scratches, and then use a soft cotton cloth to rub it counterclockwise, and after a few times, it not only reduces the scratches, but also avoids the erosion of the air on the car paint wounds.

Second, scratches that have not taken off the primer First aid products: fine wax, touch-up paint field pen Scratches with a slightly larger area can be rescued with touch-up paint. Touch-up paint pens are sold in general car supplies stores, car owners quote their own car model, the official color book is the name, you can buy the right color of the paint pen, the general price is around 40-50 yuan.

Before use, shake the paint in the touch-up pen evenly, repair the primer like nail polish, you can add a certain amount of thinner to the touch-up paint pen, so that it can be sprayed smoothly, carefully spray the position that needs to be repaired, and wait for the touch-up paint pen to wipe the place dry, and then the fine wax state regret can be marked.

Third, the scratches of the primer have been seen First aid products: demarking and rust inhibitors, self-spraying paint For serious scratches, if you can see the color of the lower primer, then it depends on the scars. But if these heavy scars appear on other parts of the body, then you need to touch up the paint, otherwise even if it is a small break, the steel plate will start to rust, and by that time, it will be difficult to prevent rust even if the paint is repaired.

The owner can first wash and wipe the car dry, apply rust remover to the scratches, and wait for 10 to 15 minutes to wipe the rust with a tissue paper to avoid the scratches and continue to rust.

It was the scooter mirror handle that knocked off a large piece, and now the mirror can be turned at any time.

If you lose a piece of your hand, you can only replace it, or you can replace it with something else, paint up a little, and you're good to go