How do I change the gear oil of the reverse gear of the tricycle, mine is the Zongshen 150 tricycle.

You look for the strap under the reverse gearGasketsUnscrew the screws, drain the gear oil, and tighten the screws. Add 200 ml of gear oil from the plastic plug above on the line.

Mikes.

That is, motorcycles with three wheels are mainly divided into three categories according to the industry classification: senior cars.

Three-wheeled trucks, passenger three-wheelers.

The method of three-wheeled motorcycle hanging reverse gear: three-wheeled motorcycles have with and without clutch, without clutch.

There are generally 4 gears, and the gear lever is pushed directly forward, which is the forward gear. Push it to add a gear, from one to four, and pull the gear lever back to downshift, from four to one.

When you are in neutral, pull the gear lever directly back to reverse gear, just one gear. Those with clutches need to hold on to the clutch, and then hang the gear, and the gear is generally the same as without the clutch.

Zongshen. Motorcycle tricycle oil replacement, the oil drain screw is located on the left side of the engine body side, after removing the internal oil will flow out, the specific operation steps for replacement are as follows: Brother Bi.

1. Use a 23 wrench.

Set on the screws.

2. Remove the screws and drain the oil.

3. Take out the filter screen and clean it.

4. Tighten the screws.

5. Add motorcycle engine oil.

For the reverse gear of the three-wheeled motorcycle, you can use 85W 90 GL-5 gear oil, this gear oil is very common, and this type of gear oil is used in the gearbox of ordinary scooters, and it can also be bought in general motorcycle repair shops or stores that sell lubricants.

If you have not changed the gear oil of this reverser, it is best to go to the after-sales service or motorcycle repair shop for the first time, see the replacement method and precautions, and then change it yourself in the future, so as not to cause trouble due to operation errors, so that the gear oil can be bought directly in the after-sales service or repair shop. If you want to change the gear oil yourself and will change it, you can go to these stores or online, prepare some tools after buying the oil and change it yourself.

The lubricating oil for the reverse gear of the three-wheeled motorcycle, different from the ordinary engine lubricating oil, they generally use gear oil, and the amount is not large, ** is not expensive, the replacement method is relatively simple, if you have enough hands-on ability and necessary tools, you can change it, it is generally simpler than changing the engine oil and the gear oil of the differential. This replacement method is generally introduced in the instruction manual of the car, if you want to change it yourself, you can also take a good look at the manual.

The gear oil replacement method of the reverse gear of Zongshen three-wheeled motorcycle is basically the same as that of other similar three-wheeled motorcycles, but if you have not repaired the motorcycle at all, it is recommended to change the gear oil of the reverse gear for the first time or go to the after-sales service or a professional motorcycle repair shop. Generally, the first gear oil change is also at the end of the motorcycle run-in period, so that the after-sales service can also check whether there are other problems with the tricycle by the way.

Lift the tricycle or use a jack to support and fix it, do not slip and hurt people, spray lubricant on the screws ready to be disassembled to reduce the resistance to disassembly, these parts include: oil injection hole screws, oil drain hole screws, shock absorber screws.

Prepare 150 ml of gear oil to be replaced, and be careful not to add more than 150 ml, otherwise there is a risk of oil leakage from the brakes and brake failure. (There are three types of gear oil: four-season oil, winter oil and summer oil).

Electric tricycle manufacturers say that idling the motor for one minute before changing the gear oil will allow the gear oil to flow out better. Unscrew the oil drain screw, and at the same time unscrew the oil injection hole screw, which increases the speed of waste oil outflow. When changing the oil, be sure to put the differential oil clean to avoid impurities remaining.

When disassembling and assembling the screws of the oil injection hole and oil drain hole, choose a suitable type of plum wrench to avoid damage to the screw and cause greater losses.

After the gear oil is cleaned, tighten the screws of the oil drain hole, remove the shock absorber screws, and inject new special gear oil from the oil injection hole, the oil is not easy to be too much, so as not to enter the brake system, which is caused.

<>1. There is a mold cavity stool at the bottom of the engine to talk about oil holes, and use No. 17 jujube to touch your hands.

The screw can be drained to the oil; The oil dipstick is next to the starting lever, screw on the oil dipstick, wait for the dirty oil to be cleaned, tighten the bottom drain bolt, and add 1L of oil from the oil dipstick hole.

2. Remember to change the reverse gear oil (change once every 2000-3000km) and the rear axle oil (change once every 5000km) for the tricycle.

Zongshen motorcycle tricycle oil change, the oil drain screw is located on the side of the body on the left side of the engine, after removing the internal oil will flow out, the specific operation steps for replacement are as follows:

1. Use a 23 wrench on the screw.

2. Remove the screws and drain the oil.

3. Take out the filter screen and clean it.

4. Tighten the screws.

5. Add motorcycle oil.

There is an oil drain hole at the bottom of the engine, which can be drained by using a 17-gauge wrench; The oil dipstick is next to the starting lever, screw on the oil dipstick, wait for the dirty oil to be cleaned, tighten the bottom drain bolt, and add 1L of oil from the oil dipstick hole.

Remember to change the reverse gear oil (change once every 2000-3000km) and the rear axle oil (change once every 5000km) for the tricycle

Summary. Depending on the engine, its principle is different. I'll just talk about it briefly.

There are two shafts in the engine: the main shaft and the secondary shaft, also called the driving shaft and the driven shaft. When the car is advancing, the main shaft drives the countershaft to run in the opposite direction through the gear on it; When the car is retreating, the spindle drives the chain through the gear on it, and the chain then drives the countershaft to rotate in a positive direction.

The above mainly means that when the forward gear is hung, the main and secondary shafts run in opposite directions; When hanging upside down, the main and secondary shafts run in the same direction.

Hello, Xiaodu, I am trying to find the answer for you, please be patient for a while According to the different engines, the principle of blocking Qi is also different. I'll just talk about it briefly. There are two shafts inside the engine:

The main shaft and the secondary shaft are also called the driving shaft and the driven shaft. When the car is advancing, the main shaft drives the countershaft to run in the opposite direction through the pure wheel of tooth balance on the top; When the car is reversing, the main shaft drives the chain through the gear on the top, and the chain then drives the countershaft to rotate in a positive direction. The above mainly means that when the forward gear is hung, the main and secondary shafts run in opposite directions; When hanging upside down, the main and secondary shafts run in the same direction.