When opening a CAD file, a dialog box always pops up, how to clear it?

Turn on your CAD2002 first (not Tianzheng!) Then open that pesky drawing (..)dwg format).

Enter it on the command line.

dxfout

command, both to change that pesky drawing, be careful to convert it to autocad2000

DXF format (to be seen).

In this case, you can use the AutoCAD2000 step to generate it

The DXF format is opened in CAD2002 and then the "Save As" operation is performed, note that Save as AutoCAD2000

dwg format).

Finally, pay attention to the above steps in CAD2002 total operation) Open the AutoCAD2000 generated in the step

dwg format).

That's it. Supplementary Method 1:

First open that nasty drawing with naivety (..)dwg format), and then convert the drawing to a tengen 3 file with the lcjb command in the tengen, and the final steps are as follows:

Turn your CAD2002 on (not Tensho!) Then open the file that has been converted to Tensho 3.

Enter it on the command line.

dxfout

command, both to change that pesky drawing, be careful to convert it to autocad2000

DXF format (to be seen).

In this case, you can use the AutoCAD2000 step to generate it

The DXF format is opened in CAD2002 and then the "Save As" operation is performed, note that Save as AutoCAD2000

dwg format).

Finally, pay attention to the above steps in CAD2002 total operation) Open the AutoCAD2000 generated in the step

dwg format).

That's it. Complementary method two (methods obtained from friends):

Method 1: Use day 7, CAD2002 direct graphic export to day 3

Method 2: If it is day 7, 2004, first open it to day 3, then open it with day 6, save it as dxf format, then turn off dxf, reopen it, save it as dwg format, there may be other ways, if anyone knows a better way, you may want to tell everyone.

Day 6 seems to be unsuccessful for graphic export.

My method is to just open the nasty file and save it as dxf, then close the file, and then double-click on the saved dxfw file, open it and save it as dwg.

I'm using the 2008 version of CAD! Not Tianzheng, I've tried it to solve the problem!

The key is to get a new version of CAD

Isn't that okay?

Save the file in DXF format, open it with CAD and save it as DWG, and there will be no such markup.

I haven't encountered this before, you can see if it's the radar-like setting in the lower right corner! or Tools on the toolbar.

Options. System.

The settings of the basic options are set! ”

Scenario 1:

If the prompt is that Internet Explorer can't link to the webpage you requested, or that "Page can't be displayed" after opening.

Please right-click on the properties of the chm file you want to open, there will be an additional "unlock" in the bottom properties, and it can be displayed normally after clicking, or save the following content in Notepad as **reg：

regedit4 [hkey_local_machine\software\microsoft\htmlhelp]

hkey_local_machine\software\microsoft\htmlhelp\

maxallowedzone"=dword:00000003 "urlallowlist"=""

hkey_local_machine\software\microsoft\htmlhelp\

maxallowedzone"=dword:00000003 "urlallowlist"=""

Scenario 2: If the prompt is:"Cannot open file mk:@msitstore:

**chm"This can be caused by the loss of files in your system or the overwriting of other versions, which can be copied from the same computer or installation CD and then re-registered.

The specific steps are as follows: Step 1: Exit all the programs that are running, click "Start - Programs".

Step 2: Type in the Run dialog box"regsvr32 c:\windows\system\"Enter, or "regsvr32 i appears.""dllregisterserver succeeded"The message is OK, restart the computer.

There are 360 security guards. 360 Security Guard can be turned on. Then run the system repair tool inside to repair the system, and then restart the computer.

If the computer keeps popping up a dialog box and says that the file cannot be opened, it may be that the computer settings are there to clean up the file.

.CHM is usually a help document, and I don't know how to open it to see what software is running (including those running in the background).

CHM is a help file.

I can't find the help file for this component.

You can find this file on another machine and copy it.

Dear Lenovo users, hello.

This is usually caused by a conflict or incompatibility with the software, it is recommended that you uninstall it and reinstall it, if it is still not resolved, it is recommended that you check the instructions of the software.

We apologize for the inconvenience and have a great day.

This is a program made by someone else has been loaded into your CAD program, it will appear when you open CAD, it does not affect the use, but if you feel annoyed by looking, you uninstall it, and then reinstall it, remember to change the path when installing!

Click the Tools-Load Uninstall App-Find the Content button, open it and see if there are any useless programs inside. Or delete all (it is not recommended that you may uninstall the plug-in) Restart the CAD.

From the command line, type: filedia

Enter, enter the number 1, and press Enter.

That's because your computer is missing fonts.

Someone else uses the font, if your computer doesn't have it, every time you open it, it will prompt you with the location of the file, which is a normal thing, and the disease is not a virus.

You can click "Cancel", then open the graphic, under the text style, change the font to something else or you leave an e-mail, I will send the font to you.