How many liters do you need for a Nissan Sunshine oil change

Hello, this car can change the engine oil by 3 liters.

1. Operate the first motive to reach the working temperature. Then use a jack to jack up the vehicle, pull up the hand brake and draft the lead beam to squeeze the front wheels with a wooden wedge. 2. Place the old oil container under the oil pan, find the oil drain bolt of the oil pan, slowly unscrew the oil drain bolt, and be careful not to touch the hot oil.

3. Move the oil container to the bottom of the oil filter, use the oil filter element wrench to loosen the filter element, and unscrew it by hand. 4. Refer to the user's manual to select the appropriate oil filter element. 5. Use new oil to apply the interface gasket of the new filter element, and screw the filter element in by hand.

1. Operate the first motive to reach the working temperature. Then use a jack to jack up the vehicle, pull up the hand brake and squeeze the front wheels up with a wooden wedge.

2. Place the old oil container under the oil pan, find the oil drain bolt of the oil pan, and slowly unscrew the oil drain bolt, being careful not to touch the hot oil.

3. Move the oil container to the bottom of the oil filter, use the oil filter element wrench to loosen the filter element, and unscrew it by hand.

4. Refer to the user's manual to select the appropriate oil filter element.

5. Use new oil to apply the interface gasket of the new filter element, and screw the filter element in by hand.

6. Put the new oil into the oil pan, refer to the introduction of the user's manual. Check the lower part of the engine for leaks.

Nissan Sun's own process of changing engine oil is as follows:

Step 1: Run the engine to the operating temperature. The car is then jacked up with a hydraulic jack, the hand brake pedal is pulled on and the front tire is squeezed with a wooden wedge.

The second bad step: put the old oil utensils under the oil pan, look for the oil drain bolts of the oil pan, and gradually twist the oil drain bolts, be careful not to touch the boiling oil. Let the oil drip out for a while.

Check the oil drain bolts, reinstall the oil drain bolts, and pay attention not to tighten the bolts too tightly to avoid damage to the oil pan.

Step 3: Move the oil container to the bottom of the oil filter, use the oil filter wrench to loosen the filter element, and twist it open. If the filter is still hot, be sure to wear rubber gloves.

Don't worry about the filter being tightened too tightly and destroying it during the whole process of removing it. As long as you don't destroy the socket screws of the safety filter element and the components around the filter element, you can do it.

Step 4: Refer to the customer's operating manual to select the appropriate oil filter.

Step 5: Apply new oil to wipe the socket seal of the new filter. If the filter is upright, you can put some new oil in the filter, which will also reduce the polish the next engine start.

Screw the filter element in by hand, and twist the filter element tightly according to the marked method (generally screw in 3 or 4 turns after twisting the filter element by hand).

Check whether there is any leakage under the engine. If there is no leak, learn to put down the car, check the dipstick, and start the engine. The display light on the instrument cluster should be turned off immediately after activation.

Eventually, turn off the engine and check the oil level repeatedly. Dispose of old engine oil and filter elements according to local policies and regulations.

Millions of car purchase subsidies.

Hello dear, your question: How many liters of engine oil is suitable for Nissan? The answer is:

The general increase of oil engine is about 3L, and the general addition of engine is 4L: 1. Because the old oil cannot be completely drained when changing the oil, such as the general filling of the engine is close to the upper limit of the oil; 2. However, the filling amount of engine oil should be between the upper limit and the lower limit of the oil dipstick, which is the best liquid level; 3. As a driver, you need to know mechanical knowledge, and it is necessary to change the oil and oil filter of the car regularly. A qualified oil filter must be replaced every time the oil is changed;

With the increase in car ownership, most people own a car, but they don't know how to maintain it, YACCO French engine oil brand will share with you how to change the oil filter.

Tools Required: Raw materials.

1. The oil section that meets the lubrication standard is one barrel, one original machine filter, and one machine filter tool.

2. A live wrench or a board suitable for the size of the oil bottom screw, an oil basin, and a piece of cotton cloth.

1. Start the vehicle for about 1 minute to make the oil flow fully, and then turn off the engine.

2. Open the oil filling port cap and loosen the filter and oil bottom screws with tools.

3. Place the oil basin under the oil bottom screw, completely loosen the oil bottom screw, and release the old engine oil until it does not flow at all.

4. Tighten the oil bottom screws and wipe off the excess oil stains with a cotton cloth. Unscrew the old filter, it is recommended to put a cotton cloth on the pad to be careful to burn your hands, apply oil to the sealing ring of the new filter, and tighten it in the direction of the burning hour in order.

6. Restart the engine for 1-2 minutes, observe whether there is oil leakage at the oil bottom screw and the filter, and if the oil leaks, the engine should be turned off in time for inspection and treatment; If there is no oil leakage, check the amount of oil in the oil dipstick after the ignition is turned off, add it to the standard position (the position where the middle line of the oil scale is on the upper side), and replace it.