Flower cuttings fast rooting tips, the fastest way to root cuttings

Flower cuttings rapid rooting skills: 1. Spray rooting solution to the mother tree.

The day before cuttings, the rooting solution was evenly sprayed on the mother, and the rooting solution was carried out in the tree after being absorbed by the young shoots and tender bark, which could make the tannin of the inhibiting growth material in the branches decrease significantly, the germination power was enhanced, and the rooting of cuttings was fast.

2. It is better to prune the branches in the morning.

In the morning, the water content of the branches of the flowers and trees is sufficient, the wound heals quickly after cuttings, it is easy to take root, and the survival rate is high.

Cuttings: Preparation and use of wound protectors for flower and wood cuttings.

3. Honey rooting method.

Honey can take root and sprout from cuttings, and it can also achieve the effect of sterilization and disinfection, of course, it is the original honey, and a little bit can promote the rooting of the branches, without worrying about provoking insects.

4. It is better to choose branches after flowers.

The post-flowering branches have the highest nutrient content, and are relatively thick and full, with a high survival rate of cuttings, and fast root and leaf growth.

5. Ring stripping cuttings.

It is conducive to the growth of adventitious roots in cuttings, and the width of the ring stripping is 5-7 mm.

6. Wicker soaking water rooting method.

The willow tree is a plant that takes root and sprouts very easily, and it is soaked in hot water with wicker, soaked overnight, and then used to soak the branches.

7. Blisters. Before cuttings, blister cuttings, such as persimmon trees, walnuts, etc., fully soak them in water and change the water many times to leach out the tannins in their bodies to facilitate the rooting of cuttings.

8. Pressing the strip into the soil.

For flowering shrubs with slender and soft branches, one or two months before cuttings, the method of pressing strips into the soil is used to promote rooting.

9. Potassium permanganate.

Soak in potassium permanganate solution for 10 hours, and take cuttings immediately after removal, which can promote the rooting of flowers and trees.

10. Yellowing treatment.

Before the growing season, cover the cuttings with a black plastic bag to allow them to grow in dark conditions, and when the branches and leaves have grown to a certain extent, cut them off for cuttings. The yellowing treatment is very effective for some flowers that are difficult to root. Yellowing treatment of shoots, generally takes 20 days, the effect is better.

This one has to be signed, let him take root quickly, of course, it's good to use some rooting agent. It can be rooting powder, or Schengen water, and of course it should be relatively clean. For example, there can't be mold in the sand or soil, otherwise it will be easy. Moldy and rotten.

The steps for rapid rooting of flower cuttings are as follows:Tools Materials: rooting powder, rooting agent, scissors, vermiculite + perlite, disinfection tools.

1. When cutting branches, you must use rooting agent, you can buy special rooting comma powder, you can also use willow branch soaking solution or white sugar solution instead, the effect is the same.

2. It must be a healthy, disease-free post-flowering branch. Refers to the height.

3. If it is a variety that is induced by ventilation and water cutting, it is recommended to add a little rooting powder to the water, and the root system will be more robust and full. Spraying cuttings with the remaining rooting powder solution after dilution can also improve the rooting rate.

4. The branches are obliquely cut at the bottom, and 2 pairs of leaves are retained at the top.

5. The medium is loose and breathable, and the ratio of vermiculite + perlite is 1:1.

6. The tools and media for processing branches should be disinfected to prevent the breeding of bacteria from causing black rods, and after cuttings, put them in a ventilated and scattered light place to keep the soil moist, and the root system can grow out in about half a month.

The fastest way to root cuttings mainly depends on the variety, cutting method, temperature, light and other aspects. Here are a few examples.

1. Ivy.

The selection of cuttings of ivy is to cut a 30 cm long section on a healthy and disease-free branch, starting from the top, cut into three sections, which can be cut into three branches.

When cutting, use sharp scissors, cut obliquely, three small branches, keep 2 to 3 leaves on each segment, and remove the rest of the leaves.

Insert into the prepared soil and water thoroughly. Place it in a bright and astigmatized position, maintain a temperature of about 15 to 20 degrees, and take root in about three weeks.

2. Blue snowflakes.

Blue snowflake cuttings are selected from the shoots on the new shoots of the year, 5 to 10 cm, cut obliquely with sharp scissors.

Keep the top leaves and shoots, and remove the other leaves below. Insert the prepared soil, water, keep it moist, but not too much water.

The placement position should be astigmatism and ventilation, and it can take root in about 20 days, and then transplant it after a week.

3. Jasmine.

Jasmine chooses the current year's born, flowering, green branches to sprout, and the tips of the branches are cut obliquely with scissors about 10 cm.

Remove the excess leaves underneath and leave the two leaves with healthy tops, and cut the leaves in half. Insert the prepared sand, water thoroughly, place until the sun is visible, and keep it moist often.

It takes less than a month to take root, and when the new shoots germinate stronger, they can be transplanted.

4. Camellia.

Camellia chooses annual semi-lignified branches, cut obliquely, and cut about 10 cm.

Remove the excess leaves and keep three healthy leaves. Dip the bottom of the cuttings in a little rooting powder, wrap them in mud (to speed up rooting), poke holes in the sand, and take cuttings.

After watering thoroughly, place it in a ventilated and shady place, and after two months, it can take root, and when it grows new leaves, the old leaves do not wilt, and transplant.

5. Geraniums.

Geraniums are selected from relatively robust branches and leaves with buds, and cut about 10 cm obliquely at the lower position of the leaf nodes.

Remove too many leaves, leave three healthy leaves, dip the cuttings in rooting powder, and let stand for three hours. Carefully insert sand, water, and place in a shaded and ventilated location.

After about two weeks, the cuttings start to take root, and when the leaves are erect and the roots are stronger, they can be transplanted.