The backup partition does not have enough space left or there is an error in the partition

It has been very clear that the error prompt is thrown, first look at whether the remaining space of the partition where the image file is saved is really large enough, if the remaining space is large, then chkdsk check the target (save the image file), the specific command format: "chkdsk x:"x is the target partition drive letter to be checked, if there is a problem through the chkdsk program check, then continue to enter this command, add f parameter to the end, and repair it.

If the remaining space of the partition where the image file is saved is not large enough, it is best to use the software diskgenius to adjust the partition, note that adjusting the partition will not affect the data, and it is a lossless adjustment.

After the above series of operations, and then back up with the software that was backed up before, there should be no problem.

How to use the one-click restore wizard: 1. Installation of the software.

Double-click the installation file back, wait for a while, the computer will automatically restart, and at the same time enter the installation interface of the one-click restore wizard (as shown in Figure 1), click the installation button, and the selection of the installation version window will pop up, the software is divided into two versions: dynamic partition version and fixed partition version, the dynamic partition version can automatically increase the space when the backup partition space is insufficient, and the fixed partition version can not change the partition space in the future, so here we choose to install the dynamic partition version, After clicking the dynamic partition version button, the computer will automatically install, and the installation success dialog box will pop up after a while.

2. Use of Software.

After the computer restarts, before entering the system, the top of the screen will appear "**press[f11]to start recovery system*** prompt, then press the f11 key to use the "one-click restore wizard" (as shown in 2), because it is the first time to use, so the system prompts to back up the c disk, then press f8 or click the "backup system" button, the computer will automatically start to back up the c disk, these operations are fully automatic, When the backup is complete, the computer automatically restarts. After the system backup is completed, how to restore it after the computer has a problem? As long as you press the F11 key when you boot up, bring up the main interface of "One-click Restore Wizard", click on the restore system or press F5 on it, and the computer will automatically start again to restore the system disk.

Isn't it the same as the one-click restore function of the brand machine?

3. Software settings.

Above we introduced the use of "One-click Restore Wizard" backup and restore system, in fact, the software has more powerful functions. On the main interface of the software, click the "Settings Advanced Settings" menu, you can open the advanced settings window (as shown in Figure 3), here we can set a permanent restore point, so that even if the C drive is formatted, we can easily restore the system, and at the same time, we can also back up CMOS settings, screen settings and go to DOS and other operations. In addition, in order to back up the security of the system, the software has a user permission setting function, which allows you to set the administrator password and user password, so that multiple people can operate the computer to ensure the security of the system.

If you don't want to use the one-click restore wizard, you can also easily uninstall it, click the "Uninstall the wizard" button on the advanced settings window, you can completely delete the one-click restore wizard, and you can also double-click the installation file, on the installation interface, click the "toolbox" button, and you can easily uninstall the "one-click restore wizard" in the toolbox window.

Landlord, do you set F11 to one-click backup and restore?

If so, it's because F11 one-click backup and restore re-splits the last partition of your hard drive into a hidden partition for backup.

One-click restore installation is installed in a hidden partition in your last disk, which is invisible in the disk. If you don't delete the original hidden partition, even if your last disk is 1000GB, you can't install it anymore.

The F11 one-click backup you use may not be good on the function. I've used a version before that you can increase it if you don't have enough backup space. It can be set in F11 and press ESC Advanced. If you don't have one, there's a way to do it.

The operation method to delete this partition is as follows: "My Computer (right click) - Management - Disk Management" At this time, you can see your hard disk partition on the right side of the window that opens, and there is a partition (IMB format) behind the last partition, this is it, use the "Right Click - Delete" method, you can delete the image of the previous backup. Just uninstall and reinstall this one-click restore, and it will give you enough space to back up the C drive.

There are other ways to solve the problem, but also depending on the specific situation, (there is also a possibility that your hard disk has bad sectors to cause one-click restore damage, now there are many machines that can't even install the one-click restore wizard, only some new machines may be easier to use.) Some brand machines, even if they are new, still need to be defragmented when installing one-click restore).

If you have any questions, you can continue to ask me, and if my reply is helpful to you, please click "Set as Adopt" below the reply, thank you!

Choose the path where you want to store your backups and set it up again.

The path to store the backup is set from the new settings.

Win7 system hard disk partition is only allowed to build 4 partitions, of which there are two types of partitions: 1) main partition drive (that is, the main partition), this type is generally used for system boot disk, windows installation disk and program installation, etc., and the main partition can generally not be divided; 2) Logical drive, this type can be used to create several logical partitions, generally used for document storage;

In the number of partitions above: c and d belong to the logical partitions in the logical drive, and the others should belong to the primary partition, so that there are obviously more than 4 partitions; Therefore, this disk can not be redistributed, and there is the above error prompt!

Try the following:

1. Use "Delete Volume" for this unallocated disk;

2. The logical drive uses "Extended Volume" to extend the deleted to the logical drive;

3. Create an unallocated disk as a logical partition in the logical drive;

If the above method is invalid, you can only delete all and re-divide, but before deleting the note, save the data to a third-party disk, and pre-select the plan before partitioning, such as the number of partitions is greater than 4, after setting the three main partitions, set the last one as a logical drive, and then divide the logical drive into several logical partitions.

In addition, it is not recommended to use a third-party partition tool to build a win7 system partition, especially if you have used a win7 partition, it is best not to use a third-party partition tool to operate, due to the particularity of the win7 partition, the third-party partition tool will often report the win7 partition error, a improper operation may cause irreplaceable physical damage to the hard disk!

It's been a hard fight, so let's take it!

1. You should delete the penultimate one, which is the E partition (you need to back up the data in E), then right-click the extended partition, select "Extended Volume", increase the size of the extended partition, and include the E block into the extended partition.

2. Right-click on the last "Free Space" in the extended partition and select "New Volume" to recreate the E partition. At this point, the new e is already a logical partition. This frees up a place for the primary partition.

3. Right-click on the previous "Unallocated Space" and select "New Volume", and you should be able to create a primary partition.

Your last disk is running out of space. It is recommended to format the last disk and re-expand the archive partition and back it up.

Backup method. Hit F11 to enter the red progress bar without stopping, and immediately click ESC to enter the backup adjustment Point F1 Enter the re-backup option (if the size of the C drive is about the same as the original, you can directly click on the backup) Advanced OK Multi-partition backup and restore [F7] Fill in the [1] hard disk, [1] partition (in the case of a hard disk) Then click the delete backup file below, the computer screen is black, and then the deletion is successful The right partition can be expanded to expand the size of the C disk file (1 of the file size of the C disk 2) OK (f4) Backup (f1) to start the backup. The last backup is gone.

It may be that there is not enough space in the partition.

Because there are already 4 primary partitions.

The MBR partition table supports up to 4 primary partitions, so you can't separate the fifth partition. There is a black bar above the unassigned option. It is the free space that is divided into the C drive.

Since it's the space that has been split by the C drive, we can put it back there. The method is to move the mouse over the C inventory and right-click - Expand the volume.

After clicking on it, the Expand Volume Wizard appears, click Next - Next - Done.

A computer's hard disk is the most important storage device for a computer. Hard disks consist of one or more discs made of aluminum or glass.

These discs are covered with ferromagnetic material. The vast majority of hard drives are fixed hard disks that are permanently sealed and fixed in the hard drive.

From the creation of the first hard disk RAMAC to the hard disk with a single disk capacity, the hard disk has gone through the following generations:

In 1956, IBM's IBM 350 RAMAC, the prototype of the modern hard drive, was the size of two refrigerators, but its storage capacity was only 5MB.

In 1973, the IBM 3340 was introduced, and he had the nickname "Winchester", which was due to the caliber and ammunition of his two 30MB storage units, which were the caliber and ammunition of the famous "Winchester Raffle". At this point, the basic architecture of the hard disk was established.

In the second picture, where the next step is not to create a new partition? Then right-click on the partition in front of it, then select the extended volume, and try to expand it on the D drive, if it still doesn't work, use DiskGenius or Aomei Partition Assistant to create or merge partitions.

The OEM partition is a dedicated partition for brand computers, and it cannot be managed under Windows, but can only be handled by Diskgen or other partition software.

ps:However, it should be noted when dealing with it,The system boot area of some brand computers will also be placed in this place,So if you delete or modify it directly,It may cause the system to fail to start,It is recommended that if you want to free up this part of the space,It is best to reinstall the system after partitioning modification,The most thorough is to repartition and reinstall the system。

It should have been partitioned before, so it can't be partitioned anymore, this can't be helped.

Here's how to do partitioning:

1.First, make the U disk into a boot disk, and then start from the U disk and directly enter the PE.

4.Reboot, boot from the USB flash drive, and enter the PE interface, as shown below:

7.Then click Quick Partition, select the number of partitions you want, OK, everything is OKAfter rebooting, you can install the system.

5Then open the iTunes operation again and see if it still says that there is not enough disk space.

End to change iTunes settings.

In addition, we can change the location of iTunes files, click on the menu icon in the upper left corner of iTunes and click on the Preferences option, as shown in the image.

Then, in the Set storage location for your new iTunes window, select a different drive than the C drive, just don't let it be on the C drive.

It is best to format the C drive with PE first. Otherwise, the situation will continue to occur.

There may be hidden partitions, if you have installed win7 or restore wizard and other software, there are hidden partitions.

Find a ghost disk,Format the C disk after entering,There is no problem,If you have not enough space for the C disk,If there is no very important information, format it all,Repartition,Win7,C disk put 30G,So there is no problem with reinstallation,After formatting or partitioning,It is recommended that you use the installation disk to do the system,There should be no problem,Please know!

If there is a problem you can hi me.

Win7 backups do take up a lot of space, but backups don't seem to make much sense.