What CNC cutting machine equipment do you need to open a panel furniture factory

The equipment required for the open panel furniture factory is as follows.

A three-row drill (10,000), an edge banding machine (10,000), a sliding table saw (45 degrees: 10,000), a gong machine (10,000). Total 10,000.

A CNC cutting machine: 80,000, an edge banding machine (50,000, at this time the edge banding machine is worse than the above function), a three-row drill (10,000), total: 10,000 (this combination is a little more exceeding, and the cutting is better).

There are also some options, that is, depending on your focus, just like the edge banding machine, the cheap 4 50,000, the more expensive tens of thousands, hundreds of thousands, hundreds of thousands, hundreds of thousands, the cutting is also from more than 10,000 sliding table saws, tens of thousands of reciprocating saws, more than 100,000 computer panel saws, hundreds of thousands of computer panel saws (after feeding or vertical and horizontal saws, etc.), drilling machines also have tens of thousands of row drills, to more than 100,000, more than 200,000 CNC drills, these all depend on your choice. For more information, please pay attention to Shunde Akun.

Cutting machine, side hole drill, blister machine.

You can search for panel furniture cutting machine manufacturers, consult and ask, some cutting machines are equipped with side hole drilling, this function can not be purchased. So you have to ask the manufacturer to see the configuration, some of the Xingcan CNC cutting machines have the function of punching side holes, just use the cutting machine and blister machine OK.

Panel furniture production line infrared side punching machine.

5-70,000, the same lead cutting machine ** can not exceed the engraving machine!

Custom furniture CNC cutting machine model configuration is more, it is difficult to define a custom furniture cutting machine, if the funds are limited, you can consider the high configuration of the four-process cutting machine, this model configuration of the cutting machine is fully functional, cost-effective, the current four-process cutting machine is more professional in the industry like Runchi four-process cutting machine, compared with peers or more advantageous.

Plate cutting 70000-350000 The most important thing to look at is the budget.

By model. There are two-process CNC cutting machines with row drilling, three-process CNC cutting machines, four-process CNC cutting machines, and woodworking machining centers Each product is divided into high and low configuration, so it is not the same, and it can be customized.

See what you do in this way, mainly do cabinets, wardrobes with a large amount of double-spindle drill bags, generally with four processes, to do door knife magazine, and to do door cabinet knife magazine plus drill bag. The configuration depends on what kind of configuration you need, and the ** of them is also different. As far as the current market is concerned, Hebei Kuike's machine is the most cost-effective.

With the development of the panel furniture industry, furniture factories have used CNC equipment to replace the traditional way of producing furniture, but due to the lack of understanding of CNC equipment, many furniture factories often fall into the misunderstanding of "low-price sales" of some cutting machine manufacturers, and often this low-price sales will make many bosses confused.

In fact, there is a way to distinguish the blind spot of the low price of the cutting machine:

1.First of all, for a cutting machine, each knife means that the equipment can complete an operation process alone, and each more knife also means an additional set of operating systems, the more complex the equipment, the more expensive it is.

2.The bed also has a great influence in the post-processing process, and the heavy-duty cutting machine body can keep the center of gravity of the cutting machine downward, and if the bed frame is not thick enough, the processed products are also unqualified. Then there are problems such as whether the sheet metal welding parts of the bed are leaked welding, open welding, etc., what material the bed is, etc., all of which should be inquired.

3.In this is the operating system used in the cutting machine, for some furniture factories with strict processing will generally use the new generation system, Baoyuan system, Weihong system, but the market value of such an operating system is about 1-20,000 yuan, but for some manufacturers who do not have high processing requirements, it is also possible to choose an ordinary system, which is cost-effective, and it is easier to accept. If the salesman of the cutting machine manufacturer tells you that the system is very high-end but relatively cheap, then there is no doubt that it may be pirated, and there is no after-sales service for the use of pirated software.

4.The control system is quite like a human brain, the brain is smart enough, and the limbs must be developed. The spindle is different from the engraving machine that needs to choose high power, generally, 6kw, 9kw, 12kw; For high-power spindles, an average of 1000-2000 should be added to each spindle; Water pump or wind pump, 11kw to add about 5000; Rack mold, slider 25, 30 start, each slider at least 200, rack more than 1000 meters; In order to meet the high speed and high precision, it is better to choose imported to improve work efficiency, and the market price is about 3000; The reducer is better used to control the speed of the equipment, and the high-precision gear train can effectively increase the torque, and the equipment is in the state of non-stop start-stop, if the reducer is not good, it will affect the life of the servo motor, and it is time-consuming and laborious to replace it again.

5.The conventional size of the market furniture model is 1200mm*2400mm, so now the cutting machine manufacturer 1325 series cutting machine table size is 1300mm*2500mm, if the sample size is larger, then the cutting machine table will be larger, the commonly used enlarged size is 2000mm*2500mm, 2500mm*2500mm, generally about 5000 expensive.

Finally, when I went to the manufacturer to inspect, I used equipment to try to cut the plate on the spot, measure whether the diagonal and opposite sides of the board were of equal length, and measure the hole distance with vernier calipers.

After so many years of cutting machine after-sales, Qingdao Lianwang Weiye's panel furniture equipment is good in terms of accuracy and service life.

What is the configuration of the electric sweeper used to clean the community or park without wasting resources?

The traditional equipment for the production of panel furniture includes sliding table saws, edge banding machines, and row drills, but now many of these traditional equipment have been replaced by CNC equipment. Such as: electronic cutting saw for mass production, customized production of CNC cutting machine, CNC row drilling, etc.

1. Non-hole process CNC cutting machine.

2. In-line automatic tool changing cutting machine.

3. Four-process cutting machine.

4. Non-porous process with row drill bag cutting machine.

5. CNC machining center for sub-mother saw.

6. Four-process cutting machine.

7. In-line automatic tool changer cutting machine.

8. Non-porous process with row drill bag cutting machine.

9. CNC wooden door keyhole machine.

10. Lead screw CNC cutting machine.

To open a panel furniture factory, you need to make cabinet equipment and door panel equipment. Such as, edge banding machine, cutting machine, etc.

First of all, panel furniture is divided into cabinets, door panels, these two can depend on their own situation, not much money to do only one kind of rest can be outsourced, can also be done.

The cabinet is mainly used for cutting, punching three-in-one holes, edge sealing, and assembly. The old version of the home has a sliding table saw cutting, row drill punching, edge banding machine edge banding. In the new version, use the cutting machine to directly cut the material and punch the front hole; After the edge banding machine is used for automatic edge banding, the side hole machine makes the side hole and wooden pin hole of the three-in-one hole.

In general, a cutting machine, an edge banding machine, and a side hole machine are required. In this way, when the cutting machine has just started, it is good to use the standard of four processes.

The door panel is relatively simple, mainly for modeling, cutting and polishing, laminating, and hinge holes. Generally, the cutting machine is used for modeling and cutting. At present, the cutting machine can also be cut, as long as the board is not too messy and hairless, the step of polishing can be omitted, directly laminated, and then the hinge hole is played with a hinge machine.

Some door panels need to be printed with UV color printing machines to do some floral decorations or something. In general, you need a cutting machine, a laminating machine, a UV color printing machine (not a must), a polishing machine (a cheap manual one, and a good plate is not needed), and a hinge machine.

To do furniture customization, why choose a CNC cutting machine?

I'll answer that question.

First of all, the CNC cutting machine is a woodworking machinery and equipment, which is mainly used for wood panel processing.

Second, the function of the CNC cutting machine is cutting, punching, and slotting, which can complete the processing effect required in furniture customization.

Third, the fully automatic control system, high processing precision, fast efficiency, improve production capacity.