Logitech s mouse is used for a long time, will the click become a double click?

The click key often used by the mouse will cause a continuous click phenomenon after a long time, because of the poor contact of the contact, although the switch contact is in a closed space, but it is not closed, or some dust and impurities cause poor contact. A click becomes a double-click. The solution can be to open the mouse to expose the key with anhydrous alcohol.

Drop 1-2 drops to the on-off key, then click the on-off key many times to clean the internal contacts, which can be repeatedly cleaned 2-3 times, and can return to normal after air drying. Try it, it should work.

Really so-so.

Logitech was really good 5 years ago, but now after it has become bigger, it is more and more water in terms of product quality and after-sales service, I have used two Logitech mice, the first one was bought in 2006, and it has been used for 6 years, and there is a problem of mouse click becoming a double click, I know how to solve it, and kind-hearted netizens said that it would be good to change a micro motion or remove the micro motion and polish the copper sheet by yourself, and then it took me more than 1 hour to repair it, and I still use it, but as the resolution of the screen is getting bigger and bigger, The dpi of the mouse mark is not enough, so I bought a new Logitech mouse, and the result was only used for 9 months, and the same problem occurred, because the warranty period was not over, I took it to Logitech's after-sales maintenance, and the maintenance staff tore off the foot sticker in person, revealing the screws, and didn't say anything, and got it inside after a few minutes, saying that I had dismantled the mouse, and said that the screws had traces of being screwed, and the this group of dead after-sales sales, I will come to you to repair it after I have dismantled it, don't you want to earn a maintenance fee, and then go home and repair it in the same way. It's just that I feel that the material of the Logitech mouse is much worse than before, and the copper sheet is obviously thinner than before, from this point it can be seen that Logitech is not as good as before, in fact, there are many good mice now, not only Logitech, it is recommended that you compare and compare online!

Bloody lesson, 2 years ago to buy a g700s, 2 years left click automatic double click, contact after-sales, only one plan to replace g603, 603 used half a year, the roller rolled back by itself. Contact the after-sales service to say that according to the 700s warranty, in order to exceed the warranty period. It cannot be repaired or after-sales.

Can only be thrown. Be cautious yourself. It's all more than 600 mice, not as good as more than 200.

Logitech is too rubbish now, if you don't believe it, you can search the Internet yourself, 603's rollback, take the defective product to make up for me, take it.

How long has it been my G1 for more than a year 3 hours a day CS a day just now.

Logitech. The left Jian click of the photoelectric mouse to double-click the buried change, which is caused by the wrong setting, and the solution is as follows:

1. First, go back to the system desktop and click [Start].

2. Then find [Control Panel.]

Click. <>

3. On the control panel page, see [View Regret Method] and select [Big Icon].

4. See the [Mouse] option and click it.

5. In the mouse properties, set as shown in the figure below, don't set the double click too fast, otherwise the mouse click will become a double bend before the scatter.

Click OK.

Logitech Optoelectronics Mouse left Jian click to double-click, which is caused by a setting error, and the solution is as follows:

1. First, go back to the system desktop and click [Start].

2. Then find [Control Panel] and click it.

3. On the Control Panel page, see [View Method] and select [Big Icon].

4. See the [Mouse] option and click it.

5. In the mouse properties, set as shown in the figure below, don't set the double-click too fast, otherwise the mouse click will become a double-click, click OK.

Because of the loss of internal parts caused by long-term pressing of the left button, if you have strong hands-on ability, you can replace the parts of the left mouse button that you don't want, but it is best to replace the new mouse.

First of all, the mouse is disassembled, and the mouse screws are generally hidden inside the foot pad and the trademark;

After taking the mouse apart, you will clearly see the internal parts of the mouse;

At this time, hold your right thumb and index finger into an O-shape, and flick it hard against the left button;

Then try to see if there is still a problem with the left button, and if not, play it again at a different angle to improve the success rate. I succeeded in this method at the first time.

Mechanical failures should be rare, and even if they are, the possibility of repair is rare! It may be poisoned, use anti-virus software to kill the virus. Or maybe there's something wrong with your mouse settings! It is recommended to check it out again!

Don't disassemble it yourself, as long as yours is boxed**, you can go to the after-sales service for free and change a new problem, it should be a key.

The main reason is that these high-end mice have low micro-motion debounce settings to improve click feedback, which has little to do with the quality of micro-motion.

The relationship between the origin and quality of the mouse.

1. Origin determines quality.

It should be clarified that "the brand does not determine the final quality, the origin is the final determinant of quality". The "quality" mentioned here is only the material and service life of the micro-movement, and does not include the hardness parameters. At present, the quality of micro-motion can be distinguished according to the place of origin, mainly divided into Chinese mainland, Taiwan Province of China, Japan and South Korea.

As we all know, many brands have built low-end product production lines for mass shipments in Chinese mainland, and the same is true for micro motion manufacturers. It is undeniable that the micro-motion models produced in the mainland are of the most ordinary quality, the micro-modes produced in Japan are of the best quality, and Taiwan Province and South Korea are in the middle.

2 Big names are ashamed to use cheap components, Yu Fengxun.

Here to talk about the most common D2FC-F-7 on the market, this micro motion is omron specially designed for the mouse model, produced in Chinese mainland, it has brought glory to Microsoft's IE mouse, but also it let go to decline, as the so-called "success also omron, defeat also omron"!

Because Omron itself is an industrial micro switch manufacturer, in fact, the D2FC-F-7N simply cannot meet the standards of industrial products, but for the mouse and users, its key travel, feel, rebound strength, speed and other aspects can be said to be very suitable, and it is these achievements that make Microsoft.

However, due to its own quality problems, after a long period of use, there are many symptoms such as double clicks and key collapse. The D2FC-F-7N's vertical contact switch is an ordinary metal sheet, and the housing and base are ordinary plastic ......Therefore, the cost is very low, and the market price is only yuan.

When in 2015, after the problem, Microsoft Guoji Qingxuan switched to Nissan's original Panasonic micro-motion in IE, but Logitech still ignored the quality problems of a large number of feedback for many years, until 2021, or stubbornly continued to purchase this defective model micro-motion in large quantities, and continued to be used in many mice, including the MX Revolution flagship model, and used such a few inferior micro-motions worth a few cents in high-end mice priced at a few hundred yuan, This really makes users angry.