What happened this morning when I found out that the Leooer gas water heater had an E1 failure?

If the water heater shows this one, it should be that there is a problem with its system, so there will be this situation, so you must first turn off all the power and check it again.

The reason why the gas water heater shows E1 is that the water heater loses power or cannot be ignited in the middle of the time, which is generally caused by too much scale in the water heater, and the scale needs to be cleaned regularly to avoid this problem from happening again.

If the water heater fails, it may be that you use too much hot water, and then it can't be supplied, so this kind of failure will occur.

If there is an E1 fault in your natural gas water heater, you had better find after-sales customer service to solve the problem for you.

If you find a fault in the gas water heater this morning, you may have to ask a repairer to help you get it, or it may be the reason for the plumbing, anyway, you can also read the manual There are some explanations in this regard.

This is not a lack of water, it should be no gas, you look at the instructions in the back, there is a very detailed introduction above, it should be no gas.

You found out that your Leooer gas water heater had an E1 failure this morning, what happened? In this case, I will find you a professional repairman, let him help you repair this thing, and also eliminate potential safety hazards.

Someone has found out, comforting Angel This tone is out of the heart, the fault is mainly caused by the home subsidy or the gas water appliance, this kind of stock.

I think that if there is a fault in this, you must take off the order, except because it is very dangerous.

E1 is an ignition failure, if it is good and bad, it should be considered that it is caused by scale or the failure of the induction needle.

The gas water heater is water-gas linkage, that is, only when the water flow rate reaches a certain requirement, the ignition switch can be opened, so as to achieve ignition heating. However, after the water heater is used for a period of time, there will be scale in it, which will cause the hot water outlet to become smaller, and then drive the water inlet to become smaller, and the water flow will be unstable. In this case, you can buy a water heater electric circulation cleaner online to clean up the scale.

There is also a situation where there is too much dust on the induction needle, and after the water heater is ignited, the induction needle cannot sense it, and it will automatically turn off the fire. In this case, close the gas valve, open the lid of the water heater, find the induction needle in the combustion chamber, and polish it smooth with sandpaper.

What happened this morning when I found out that gas water heater was malfunctioning? There must be a problem with that line, so hurry up and repair it.

Is there not enough air pressure when you run out of gas?

Gas water heatersThe reasons and solutions for E1 are shown as follows:

1. If the temperature is too high, turn down the set temperature of the water heater.

2. If the wind pressure switch fails, replace the wind pressure switch.

3. The temperature probe is damaged, and the component is replaced.

4. If the motherboard is faulty, you need to contact the maintenance personnel for maintenance.

Precautions for the use of gas water heaters1. Purchase water heaters according to the gas source. The choice of gas water heater for a home depends on the current gas source used in the home. The main gas sources are artificial gas and liquefied petroleum gas.

There are several kinds of natural gas, all kinds of gas can not be used, and it is necessary to pay attention to identification when purchasing.

2. It must be installed by professionals. The installation of gas water heaters must be approved by the gas company, and professional installers must install and obtain a use permit. When purchasing a water heater, we should pay attention to comparing the manufacturer's after-sales service.

Whether there is a local maintenance point or special maintenance department.

The above content reference: Encyclopedia - Gas Water Heater.

Resolution. 1) Adjust the LPG pressure reducing valve, or replace the pressure reducing valve.

2) Confirm and adjust the secondary pressure of the small fire.

3) The gas valve can be disassembled and cleaned, if the rubber film in the gas valve body is deformed, a new gas valve body needs to be replaced.

4) Replace the fan.

5) The resistance of the solenoid valve coil should be about 100W.

6) Check whether the proportional valve voltage is about 10V for small fire, about 15V for medium fire, and about 20V for large fire.

7) Replace the pulse igniter.

Cause of the failure. 1) The gas pressure of liquefied gas is too high or too low; The pressure after the liquefied gas pressure reducing valve should be adjusted to about 2800pa. In winter, the temperature is low, the vaporization rate of liquefied gas is slow, and the gas supply is insufficient.

2) The rated gas pressure of natural gas should be 2000pa, and it is not easy to ignite when the pressure is small.

3) When the liquefied gas cylinder is used, it is inverted, and the residual liquid is poured into the gas valve of the water heater, resulting in abnormal operation of the gas valve.

4) The fan works abnormally, and the fan does not rotate.

5) The solenoid valve is not opened, and the coil is broken.

6) The proportional valve coil is damaged.

7) Pulse damage.

E1 in the water heater indicates that the ignition has failed or has stalled halfway. The water heater cannot catch fire, which may be caused by the damage of water, gas, electricity and other components, or it may be caused by the blockage of the hot water pipeline caused by the scaling of the waterway

If the flame sensor needle is too high or too low, that is, it is not in the position of the highest temperature capacity of the flame in the fire, or the fault of the flame needle will cause the water heater to fail to ignite and E1 failure will occur. The sensor needle needs to be adjusted and replaced.

If there is too much scale in the water heater pipe, resulting in a large back pressure on the flow of the water channel, it will also cause the water heater to not catch fire, this is because the gas water heater is controlled by water consumption, and there is a minimum water flow requirement, if the requirements are not met, the water heater will not be able to release gas and open the igniter, and it will not be able to use, and the water heater needs to be descaled.

Maintenance Method:

1. Clean the inner tank regularly, because of the trace impurities and minerals contained in the water, after long-term use, it will slowly precipitate, if it is not cleaned, it will affect the water quality and the service life of the whole machine;

2. The user of the electric water heater regularly asks professionals to check the equipment every year to check the safety performance and possible potential hidden dangers to eliminate, 3. If it is idle for a long time, the power supply should be turned off and the water storage of the inner tank should be emptied;

4. In order to ensure the normal use of the water heater, the safety valve needs to be maintained no less than once a month to ensure the normal pressure relief of the safety valve.

Hello friends, 1. If the gas water heater E10 does not work, it means that the ignition has failed or the ignition has been turned off halfway. 2. There are many reasons why the gas water heater is not good to ignite, and the damage of any component of water, gas and electricity will cause the water heater to fail to ignite. But now the quality of water heater components is generally improved, not so easy to break, in fact, in many cases, the reason for the fire is because of the scaling of the waterway caused by the blockage of the hot water pipeline, resulting in the back pressure of the waterway flow is larger, to a certain extent.

3. The water-gas linkage device of the hot water pants filial piety device will think that the delay is that the hot water faucet has been closed and the gas channel is closed, and there is no gas, of course, it cannot be ignited. If the hot water tap is fully turned on recently, the hot water pressure is smaller, and the possibility is greater. Now that the igniter is working properly, it is even more certain.

Hello, dear, I am happy to answer for you, according to the inquiry, what is the fault of the water heater E10. Normally, if the water heater shows E10, it means that the point has failed or that it has failed halfway. 1. Gas heating:

The battery of the water apparatus is broken and not energized, resulting in the appearance of e10 without ignition; 2. The solenoid valve of the water heater is broken; 3. It may be that the water diaphragm of the water-gas linkage valve is aging; 4. The control element of the ignition is partially broken and cannot work normally. Solution: 1. First check whether the ignition indicator is on or not, and the ignition indicates that the ignition is normal.

2. If the solenoid valve of the gas water heater is broken and cannot be ignited, it is necessary to ask professional maintenance personnel to check the solenoid valve, and it should be replaced in time if it is seriously damaged and endangers safety. 3. The water diaphragm of the water-gas linkage valve of the water heater can not be ignited when it is aged, the water diaphragm is an important component of the work, and the water heater is used for a long time, and it will be aged if you do not pay attention to timely inspection and maintenance, so it is necessary to replace the water diaphragm in time. 4. If the control element of the ignition is broken, replace the new component in time.