What to do if the glue of 502 dripped onto the fingernails

Wipe it with oil or hand cream, use insulating oil, pour some insulating oil from the transformer on the table, 502 glue will quickly become soft and can be rubbed off quickly. 502 glue is a kind of resin glue, as long as an organic solvent that dissolves the resin, such as acetone. However, acetone is toxic if inhaled, so pay attention to how to use it, and you can stuff the adhesive part into the bottle.

It is said that if you put it in the refrigerator and freeze it, the glue will also fall off, you can try it first Stick 502 glue on a small area, just soak it in hot water, if you stain a large area with 502 glue, apply acetone, and wait about 5 10 minutes to remove it. 502 glue is a kind of resin glue, as long as you use an organic solvent that dissolves the resin, such as acetone. However, acetone is toxic if inhaled, so pay attention to how to use it, and you can stuff the adhesive part into the bottle.

It is said that if you put it in the refrigerator and freeze it, the glue will also fall off, you can try it first Stick 502 glue on a small area, just soak it in hot water, if you stain a large area with 502 glue, apply acetone, and wait about 5 10 minutes to remove it. 502 glue is a kind of resin glue, as long as you use an organic solvent that dissolves the resin, such as acetone. However, acetone is toxic if inhaled, so pay attention to how to use it, and you can stuff the adhesive part into the bottle.

It is said that if you put it in the refrigerator and freeze it, the glue will also fall off, you can try it first Stick 502 glue on a small area, just soak it in hot water, if you stain a large area with 502 glue, apply acetone, and wait about 5 10 minutes to remove it. Use banana water to drop on the glue stains, and at the same time use an old toothbrush to stir constantly, until the glue stains become soft and take off, then rinse with water, brush repeatedly, and brush until clean. Put an absorbent cloth on the back of the garment with glue marks, then apply some white vinegar to the glue marks, and finally scrub it clean with cotton dipped in water.

Acetone, gasoline, sesame oil, etc., poured some insulating oil from the transformer on the hand, and the 502 glue quickly softened and finally rubbed off. It can be removed by using toilet cleaner, which sounds dirty, but I think the effect is better. After using it, be sure to wash your hands Ha I do nail art, and I often come into contact with these things, so if you get on your hands, you can wipe them with nail polish remover.

Because false nails are usually glued with 502, nail cleaning blisters are usually used first when removing nails, which can make 502 melt.

Squeeze the fingerprint at right angles, it will fall off and it doesn't hurt, I used it when I made the model, it works!

<> "What should I do if my hand is stuck with 502 glue."

1. Use the hardness of glue:

502 glue is very hard after drying, this feature is an advantage and a disadvantage, the advantage is that it can be a good glue to harder objects, but some of the greater flexibility often has no long-term effect, that is to say, the adhesive is very good at the beginning, and the glue will be opened after a period of time. Take advantage of this feature, when your two fingers are glued together, rub the glue between the two fingers vigorously, the method of kneading is actually very casual, mainly to make the glue loose. After rubbing for a while, try to see if you can separate the two fingers, if not, continue to rub and the problem can be solved within half an hour.

2. Blister:

This method is relatively simple, that is, when the glue has just dripped on your hand and has not dried, quickly put your finger into the cold water, soak it for a few minutes, you can see that the glue has become a solid, and you can easily buckle the glue off your hand. If the glue is already dry on your hands, then you will have no effect if you use water again, so the timing must be good.

3. Natural shedding method:

If your hand is stuck to a piece of paper or other small things, don't worry, if this does not hinder your daily life, you let the glue stay in your hand for a day, generally within two days will be scattered and shouted that it can automatically fall off, this method is to wait, don't be anxious.

4. Dissolution method:

In fact, there is no 502 that can be completely dissolved, and it can only be softened slightly, for example, the insulating oil can play a softening role, and it can be quickly rubbed off after softening. Some people say that acetone is highly toxic, so don't use it lightly. If you don't have insulating oil, you can use gasoline, but if you can't do it, you can only try it with cooking oil (I haven't tested it, I don't know if it works).

5. Use insulating oil

Use the cover to pour some insulating oil from the transformer, and then apply it to the glue part, and the cured 502 glue will soon become soft, and then it can be rubbed off.

Ways to prevent 502 from sticking to your hands:

1. If you often use 502 in your work, in order to prevent the glue from sticking to your hands, apply flour or foundation and other powdery particles on your hands in advance, or simply rub some soil on the ground, and the glue dripping on your hands can only stick to the powdery substances on your hands, and your hands have nothing to do. The best thing to do is to apply some hand cream to your hands beforehand.

2. Wear cotton gloves: gloves can prevent glue from dripping onto your hands, but not all gloves can play a protective role, if the gloves are rubber, plastic trembling, the glue will melt the gloves and release heat, which may burn your hands. So use cotton gloves for gloves.

3. Moisten your fingers: There is also a relatively simple way to sprinkle some water on your hands, and the glue will quickly become solid when it encounters water, and it will not be able to touch your ** at all, and you will not be able to stick to your hands.

Soak in hot soapy water and then pick off.

To remove the 502 glue from the nails, you need to prepare: a bottle of wind oil essence.

1. First, apply an appropriate amount of 502 glue to the nail as shown in the figure below.

You can use hot water to soak first, which can play a good softening effect. You can also use gasoline to scrub, which can effectively remove 502 glue, do not use blindly, and use it vigorously by hand.

1. Go with the flow and wait for it to fall on its own. 502 glue sticks to ** for a whole day at most, and usually he will run off with sweat. Although some agents can remove 502 glue, it is not clear whether they are harmful to the human body.

In fact, the hard pick can also be removed, but there is a great probability that the trembling grandson will be damaged before dispersion**.

2. Wipe it with laundry detergent, shower gel or soap that can be bought in the supermarket.

3. Do some protection before each use, and apply some hand cream with a lot of oil on your hands. It can effectively solve the problem of glue sticking to your hands.

4. Cover the glue with banana water, and repeat the brush while rinsing, wait until the glue on the ** falls off by itself, and then rinse it with water. White vinegar also works wonders for removing gum, apply some white vinegar to the sticky place, wipe it repeatedly with water-soaked cotton, and then rinse, it doesn't take long to get better.

5. Use insulating oil, cover the oil in the sticky place, this side will quickly become soft, at this time quickly wipe hard, the glue can be easily removed.

6. Cover the original place where the glue is to be removed with a new layer of glue. The glue of the place will be soft again. Then seize the opportunity to immediately rinse with water, and the glue will wash off.

7. If the area of the glue to be removed is very small. Soak it in warm mosquito repellent toilet water and you're good to go. If the area is a bit large, it is recommended to soak it for a while.

The hand is stuck with 52 glue, and the solution is as follows:1. You can immediately rub it with soapy water or diluted sodium bicarbonate solution, and if it sticks between your fingers, you can try to separate it after rubbing.

2. If it just sticks to your hands, you can immediately rinse it with cold water to solidify the colloid, and then try to pick it off.

3. Dissolving method, you can use a cotton swab dipped in some gasoline to rub, which has the effect of removal.

502 glue has a strong stickiness. If the hands are sticky, you can soak them in warm water, and they can generally be eliminated, and then liquor, nail polish remover, and gasoline also have a certain effect. Good luck!

I believe everyone is familiar with 502 glue, it has a particularly strong stickiness, and because 502 glue is fast, it is easy to stick wrong or stick to the hand, etc., accidentally 502 glue sticks to both hands, or accidentally drip on the ** will immediately dry and hard, causing us to become panicked, and even at a loss. So let's introduce some methods to teach you how to deal with your hands if they are stuck with 502 glue.

Method 1:

When you encounter the problem of 502 glue sticking to your hands, don't pull it hard, which is not only useless but also damages. If you encounter this problem, you can drip some toilet water or wind oil essence on the place where your fingers are sticking, and then rub the two fingers together with each other. This movement must be slow.

After rubbing for about a minute, the 502 glue will automatically melt and dissolve, which is a particularly simple and practical method.

Method 2:

In this case, we can first prepare a little warm water, about a small bowl of water. Then soak your fingers in warm water for a while until the 502 glue on your fingers is soft, then sprinkle a little salt on the surface of your fingers. Finally, gently rub the 502 glue and it will fall off.

Method 3:

When using 502 glue, if you want to prevent the glue sticking to your hands, you can first squeeze some hand cream into the palm of your hand, and then rub your hands against each other. This will allow the hand cream to form an oily protective film on the hands. After the protective film is formed, when 502 glue is used again, even if the glue drops on the **, it will not stick together, which is very effective and effective.

The above is the specific solution to deal with the hand being held by 502 glue, I believe you can learn it soon.