How to adjust the gas stove damper, there are two black circles on the left and right sides of the g

I finally figured out how to adjust the damper of the gas stove! It took 2 days to get it done! It's actually quite simple! I started reading a lot on the Internet, but I didn't understand it! The reason is that there is no picture, it is really hard to say, let me try!

First of all, the left and right stove eyes have their own dampers, which should be adjusted separately. The stove doesn't need to be adjusted in eight pieces!

Besides, what the damper looks like, you have to find the right one: turn the stove over, and on the side of the furnace eye, two iron sheets will be exposed, which are attached together, and they are worn on one of the shafts. There are teeth on the arc length of one sheet, and a tooth on the other, and the tooth is stuck in the tooth of the previous sheet.

There are 2 holes on the two iron sheets, which are the damper holes.

The third step is to practice the air control door: break the teeth stuck in the teeth, stagger the two iron sheets in opposite directions and turn an angle, and get stuck in the other tooth, you can find that the holes on the two iron sheets will increase or shrink.

The fourth step is how to adjust and adjust. Turn the stove over and light the fire again. Stagger the damper one tooth and one tooth, and observe the fire while adjusting.

If the fire is red, it means that the oxygen is not enough, the combustion is not sufficient, the energy is wasted, and the pot will be blackened! Therefore, adjust the damper hole in a large direction until the fire turns blue. If the damper is too big, the ratio of gas and air is not right, it will not ignite the fire, or the fire is very small, the stir-fry will not be fragrant, and you should be hungry when you wait for dinner, so you should adjust the damper hole to a small direction, and adjust it to the fire with the sound of "whirring, whirring" is the best.

In short, it's right to tune to the blue fire with a "whew, whew"!

Give it a try! It will be a success!

When the gas stove appears to burst from the fire, yellow fire, no fire in the outer ring, etc., you need to adjust the damper, whether it is a paddle type, or a knob type, as long as it is an external type, adjust it in one direction first, and when the gas stove appears to burst from the fire, yellow fire, no fire in the outer ring, etc., you need to adjust the damper, whether it is a paddle type, or a knob type, as long as it is an external type, adjust it in one direction first

Let the flame make a whirring sound, and don't have a red fire, so that you can achieve the purpose of cooking quickly and saving gas!

The gas stove manual should be written clearly, adjust it according to the manual, or call the seller to adjust it for you.

There is a dripping sound when ignition, which means that the pulse igniter is good, and you can observe whether the position of the spark is aimed at the place where the gas is out. If the battery is not charged, there will be no Didi sound. It takes 30 seconds to let go after ignition, because the heat sensitivity of the stove should not be sensitive, and it needs to reach a certain temperature to be sensitive, and it can be replaced with a new one.

The damper usually doesn't need to be adjusted, the damper is at the head of the stove, open the panel and you will see it.

How to adjust the damper.

When the gas stove is bursting from the fire, yellow flame, no fire in the outer ring, etc., you need to adjust the damper, whether it is a paddle type, or a knob type, as long as it is external, adjust it in one direction first, if the flame has also turned, please continue, if it is worse, adjust it in another direction, you don't have to remember the direction.

If the gas stove appears: burst from the fire, yellow fire red fire, no fire in the outer ring, tempering, etc., you may wish to adjust the damper to try, do not remember to adjust the direction, first adjust it in one direction, if the situation improves, please continue until ideal.

If the situation is worse, try the reverse until it is ideal, whether the damper is ideal or not, with no yellow flame, no fire and strong firepower as the standard.

The small circle in the middle of the gas stove refers to the small fire eye on the gas stove, if you find that this small fire eye is faulty, you can try the following repair methods:

1.Disassemble and clean: First of all, you need to close the gas valve, then disassemble the gas stove, remove the faulty small fire eye, clean its surface, and then reinstall it to open the valve for trial.

2.Replace the fire eye pin: If the cleaning is ineffective, then the small fire eye pin of the gas stove needs to be replaced. You can remove the faulty eyebolt and go to a nearby repair shop or market to buy a new one that fits it and install it back.

3.Check the igniter: If the problem is not with the small fire eye lit by hand, but on the igniter, then you can check whether the battery of the igniter is dead and needs to be replaced, or clean the electrodes of the igniter to ensure that the electrodes are in good condition.

In short, repairing the small circle in the middle of the gas stove needs to be operated carefully, and should be carried out with the gas valve closed, if you are not sure about the operation steps, you can consult a professional maintenance personnel. At the same time, pay attention to the use of safe materials and tools for maintenance to ensure your own safety.