There are several ways to search the table for the big pot lid, how to search the table for the smal

Generally automatic. There are also added parameters.

1. Adjust the receiver of the small pot lid to about 10 degrees south-west.

<>3. Connect the other side to the set-top box.

<>5. Press the search button of the set-top box.

Lou Yi is not right, the landlord wants to use ** one on CCTV 1 to tune as long as the signal quality is adjusted to the highest. It must be the quality and not the signal strength. It is better to split the satellite channel in the satellite 6b. Taido.

You can use the remote control of the Sakura receiver to press the signal button, and you will have these signals.

I'm fascinated by the cauldron. I helped people transfer 1,000 large and young pots in our village, charging 15-30 yuan each. I also help netizens online.

But people ask every day. I can't find them, and then I can't go to every one. I'm posting.

You QQ me.

After that, there will be a crash, and the remote control will fail and cannot be exited. Note! It's not a dead end.

Solution:Unplug the signal cable,Automatic search will be completed,Due to no signal search,After the search, it is displayed that 0 sets of TVs are found,But at this time, the remote control can be used but the receiver is still in a state of no program。 Then connect the signal line, enter the Laidan, and manually search the four groups of ** devices.

Method 2: Factory reset.

I tried it today, and the upgrade program did enter the receiver, but if the upgrade program was started, only the serial number changed from to , and the upgrade bar did not change at all. Then it automatically enters the automatic search, and after 39%, the progress bar does not move. But the frequency is increasing all the time.

You interrupt and exit. Not a single show was left behind. Uninterrupted rollouts, the frequency is increasing all the time.

It's like a dead machine. The solution is to go to the settings, go back to the factory state, and the password is 9999 or 0000Then enter the manual search, there is no program at the first frequency, there is a program when you enter the frequency 2 search, there are programs at the frequency of three or four, and there are 54 programs at the three frequency points of Huai Gai 2, 3, and 4.

It's the same as before.

The lid of the cauldron must be equipped with a set-top box, which can only take dozens to 100 units.

If there is no set-top box, the cauldron lid is only equivalent to the antenna of the TV.

The set-top box is available where you buy the lid of the cauldron.

1. Adjust the receiver of the small pot lid to about 10 degrees south-west.

<>3. Connect the other side to the set-top box.

<>5. Press the search button of the set-top box.

1. Adjust the receiver of the small pot lid to about 10 degrees south-west.

<>3. Connect the other side to the set-top box.

<>5. Press the search button of the set-top box.

The possible reason why the small pot lid only searched for 39 sets:

The parameters of the Zhongxing-9 satellite have been modified, and some programs have been encrypted and transmitted, resulting in the set-top box programs not being able to be watched.

How to install the Household Pass:

1. Assemble the antenna and install the high-frequency head: install and connect the antenna and the high-frequency head according to the manual.

2. Cable: Connect the cable on the set-top box with the cable on the TV.

3. Adjust the antenna elevation angle and azimuth angle

Elevation angle: If the scale on the antenna has been corrected, the queried angle is used;

Azimuth: due south to west.

The north is about south-west, and the elevation angle is degrees.

The south is about 75 degrees west, and the elevation angle is degrees.

4. Press the "Menu" button of the set-top box remote control to enter the next menu of system settings, find the program search, select automatic search, click OK, and wait for the search to complete to watch TV programs normally.

5. If it is a third-generation Zhongxing 9 machine, it also needs to be located to open the card before it can be used.

Set parameters: 1. Press the "Menu" button on the remote control to enter the "Main Menu" interface and select "System Settings";

2. Enter the password "9999";

3. Select "Installation and Signal Detection" in the "System Settings" interface (selected by default), and press the "Confirm" button of the remote control twice. Stand behind the satellite dish and let the front of the satellite dish slowly rotate from due south to the direction of the satellite (it is recommended to turn slower than the speed of the second hand of the watch). In the process of rotation, you should always keep an eye on the change of "signal strength" and "signal quality" in the debugging interface of the satellite receiver on the TV, and stop when the signal turns green, indicating that the satellite has been preliminarily identified and the satellite signal has been locked;

4. Network connection settings. IP settings: , port settings: 4567 or 04567;

5. The area code is set to the first six digits of the local ID number;

6. Turn off the power of the set-top box, insert the mobile ** card and smart card, and then turn it on;

7. Select "Base Station Information" in the system settings and press Confirm;

Yours is with automatic upgrades, and now there are 39 things that are upgraded and upgraded in my family.

It's upgraded again. It used to be 46, but now there are only 39.

Follow the steps below

1. Turn on the power of the set-top box.

2. Press the "Menu" button of the remote control of the set-top box.

3. Enter the "System Settings" menu, as shown below