How to configure the interface IP address of the router

I don't understand which interface you want to configure IP,The general configuration is that after you log in to the router,First configure the WAN port,If it's ADSL or the like, select PPPoE,Then enter the post number password on the line,Then see if there is a need to configure the LAN port,By default, it's all configured,You only need to configure the WAN to go online。

61 (that is, the ISP gives you), the E0 port is matched, the address is your intranet gateway, and the address of the PC under the E0 port must be matched with the same network segment, such as, , the mask is matched. When you actually go online, the router converts the address of your private network segment 192 into the public address of 210 before surfing the Internet, because the default private network address cannot access the public network.

Connect the LAN port to the network cable and then connect to the computer.

Then log in to the router.

It's okay to set the native IP of the route, for example.

The default is that you can change it to.

Log in to the router first, (there is an IP address on the router), and then follow the prompts to configure.

In today's era of rapid network development, routers play a pivotal role, and we need to master more and more relevant knowledge, so do you know how to set the IP address of the router LAN port? The following is how to set the IP address of the router LAN port that I have collected and provided for you, I hope it will help you. Welcome to read and learn!

The router LAN port IP is the sameLight catsConflicts

If the router is connected to the Telecom Optical Modem to access the Internet, the IP address of the Telecom Optical Modem is: At this time, if the IP address of the user's router is also :. After typing : in the browser, the setting interface of the telecom optical modem will be opened, instead of the setting interface of the routing device.

The IP address of the router conflicts with the modem

At this time, you need to modify the IP address of the router LAN port, you can change the IP address of the router LAN port to: , so that you can enter the router settings interface normally and set up the router to surf the Internet.

Modify the IP address of the LAN port of the router

Tips: When using the telecom modem, it does not necessarily cause IP conflicts, and it is related to the model and router brand of the modem; Sometimes there is a conflict problem, resulting in the opening of the settings interface of the modem instead of the router settings interface when you enter it in the browser.

How to set the IP address of the router LAN port.

2. The IP address of the router conflicts with the router.

In some specific cases, it is necessary to connect two or more routers to access the Internet, such as pulling a network cable from the landlord or neighbor's house, and adding a wireless router to the company's wired network.

Wait a minute. However, at this time, it is not possible to set up the router in the normal way, because there are multiple routers in the network, resulting in IP address conflicts, so it is necessary to modify the IP address of the LAN port of the Lunabi device.

Two routers are connected to the Internet

Change the IP address of the LAN port of the router

Pay attention to the problem. 1) If the IP address of the original router in the network is, add the IP address of the router.

2) After modifying the IP address of the LAN port, the router only needs to set the dynamic IP address to go online, and the second router can go online.

In the above two cases, it is necessary to modify the IP address of the router LAN port, of course, users can also modify the IP address of the router LAN port according to their own preferences.

The conventional settings include the WAN port setting, that is, the Internet access setting; and LAN settings, i.e., intranet settings.

The WAN settings should be tailored to the way you access the Internet. Common ones include dynamic addresses (usually when connected to a first-level router), static addresses (usually dedicated lines), PPPoE dial-up (for home use), and occasionally other Internet access methods such as VPNs, but they are rarely used. Proper WAN settings are a prerequisite for routers to access the Internet.

The LAN setup is usually to use the private C-class IP at the beginning. Such as or. These are also the two addresses commonly used in the factory status of the router.

Of course, if you don't set it according to this IP mode, it will not affect the networking, for example, many people also use it as the beginning of the LAN setting. In addition, the LAN address of the router does not necessarily have to be 1 at the end, and 1 cannot be used in some specific environments (for example, 1 is already used for the primary router when bridging).

The address setting of the route is roughly the same, of course, in the specific networking environment, there will be some specific requirements for the setting, which cannot be described in detail.

The number of computers connected to the LAN is too large and the router port is not enough, we need to use a switch or use a router to expand the port

Setting: Route A is the primary route, and Route B is the slave route!

First, set the WAN port status of Route A to PPPoE dial-up status, and then fill in the account and password of ADSL dial-up.

Second, set the IP address of the LAN port of Route A to the IP segment of the LAN port to the network segment mask.

Third, set the LAN port IP address of route B to the LAN port IP segment to the network segment mask.

Fourth, set the WAN port status of Route B to static IP and the IP address to Mask gateway.

Fifth, connect the WAN port of Route B and any LAN port of Route A with network cables.

Through this method, the router can be connected to the router to achieve the purpose of expanding the router connection port on the LAN.

Go to the router first, then the port, and then configure.

At least tell me what model of router you have, Cisco routers need no

SH, Huawei basically doesn't need it, Hua 3 depends on the situation, it's all different. And if you configure a normal router and not a Layer 3 switch, the IP address that is not called the LAN port should be called the LAN gateway.

Connect the network cable and router correctly, and pay attention to the WAN port of the home broadband cable.

Use a computer or mobile phone to connect to a wireless routing signal, the new route has no password, and the name is the routing model.

Open the browser and enter the route management address in the address bar, generally, there is also a special letter address, you can take a look at the nameplate on the back of the router.

When you log in for the first time, set the password for the router. If you do not use the default password admin to log in.

Then use the router's setup guide prompt to set it step by step, the broadband account and password are provided by the operator, after the setting is completed, click Save.

Then select WPA2K in the wireless security settings, enter the wireless connection password, and click Save.

Once you have completed the above steps, restart your router and you will be able to use the router.

If you want to change the address of the LAN port, you can select the LAN setting option to set a new address, which is the default.

After logging in to the router, the network parameters, WAN port settings are the network connection settings.

The LAN port setting is to modify the IP address of the private network.

1. Set the IP address of the local computer to be obtained automatically.

2. Open IE browser, enter or in the address bar, and enter the default value in the pop-up username and password box, that is, admin admin.

3. You can set it up after entering the router settings interface.

How do you set it, change the parameters of the LAN port in the LAN port settings in the router, and set the Internet access settings in the WAN port settings.

The first step is to manually set the IP address of the computer, set the IP address to any number between 2-250, that is, it cannot be 1), and the subnet mask is the default gateway.

The second step is to connect to the router (because it has been used by others, restore the router to factory settings first, the method is to dial the power supply first, poke the reset with a toothpick, and then turn on the power and wait for ten seconds, and then release it).

Step 3, enter the routing setting interface (, click on the setting wizard on the left, next, select the first one (ADSL network), next, enter the username and password (pay attention to the case), and then press Done.

Fourth, click on the connection status on the left, and then click on the connection in the middle on the right, wait a while, and see that there is receiving and sending data.

Step 5: Set the IP address of your computer to be obtained automatically.

As for the DNS address, you can get it automatically.