How to use a wired router and a wireless router at the same time, how to set it up

Changed the IP address of the LAN port of your wireless router to 251-253. Then turn off the DHCP of the wireless router. Directly connect the network cable pulled from the line to the LAN port to access the Internet View the original post

1.The wireless router Internet access mode has been changed to automatically get 2Change the LAN port address of the wireless router to a different IP segment from the L1 route 3

Select the wireless option to the wireless router and set the wifi password 4Well, it seems to have worked. View the original post

Change the IP address of the LAN port of your wireless router. If it is different from the LAN port IP with a line. It's okay not to change it. Then turn off the DHCP of the wireless router. Directly connect the network cable to the LAN port to access the Internet View the original post

The router address is set to the same CIDR block. Turn off the LAN port of the DHPC network cable. Will the technician not understand? 2345 should make a low-level problem area (non-technician area) View the original post".

Dynamic IP is OK Wireless router is connected to the LAN port where you have the line by Internet access Dynamic or static IP can be used Don't PPPoe View the original post

Just change the gateways of the two routers to different ones, simply View the original post

The following describes how to set up a wireless router to connect a wireless router to another wireless router

1. How to set up the main router:

1. Plug the network cable (bus) into the WAN port of the wireless router, plug one end of the network cable into any LAN port of the wireless router, and connect the computer network card to turn on the power of the router.

3. Then enter admin, the default account name and password are the same (there is also a prompt for the original data on the back of the router) to confirm.

4. After entering the wireless router setting interface, select the Internet access method according to the setup wizard (different broadband options are also different), and enter the Internet access and password.

5. Save and continue to set the wireless key, (it is recommended to use a combination of numbers and English for the password, and it is best to use the @ symbol in the middle, so as to prevent others from rubbing the net).

6. After saving, you can surf the Internet normally.

7. If it is abnormal, you may wish to click the reset button of the wireless router and set up the router again.

Second, the setting method of the secondary router:

1. Do not connect the secondary router to the main router first.

2. One end of the network cable is connected to any LAN port of the secondary router, and the other end is connected to the computer.

3. Change the LAN port IP of the login interface through the computer browser to avoid conflicts with the IP segment of the main router;

4. WAN port Internet access mode selection: dynamic IP connection, enable DHCP server.

5. Wireless settings and keys, save and exit.

6. Connect a network cable from any LAN port of the main router to the hall belt WAN port of the secondary wireless router, and the computer can access the Internet at this time.

With the rapid development of wireless networks, wireless routers are also an indispensable part of our lives; Many friends have a wired router at home, and they want to connect a wireless router to achieve wifi Internet access, so I will introduce the operation method of connecting a wired router to a wireless router in detail.

How to connect a wired router to a wireless router.

The first type: Route A LAN port connects to Route B WAN port.

1. Wired router settings.

1. Enter the wired router setting interface and set the LAN port lead;

2. WAN port setting, connection type PPPOE, fill in the Internet account and password;

3. DHCP setting, DHCP server is selected to enable, and the address pool is automatically obtained at the start and end, which needs to be in the same section as the gateway.

3. Wireless router settings.

Open the browser and enter the router setting interface, only by setting the wireless router IP in advance can you enter the setting interface, click the WAN port to start setting;

5 Change the LAN IP to refer to any number that is not occupied in the 0 254 zone.

6 Click Storage, restart the router and complete the setting; The main purpose of the WAN port here is to use the wireless router as a secondary router.

The second type: A route LAN port connected to B route LAN port.

1. Wired router settings.

1. Enter the wired router setting interface and set the LAN port lead;

2. WAN port setting, connection type PPPOE, fill in the Internet account and password;

3. DHCP setting, DHCP server is selected to enable, and the address pool is automatically obtained at the start and end, which needs to be in the same section as the gateway.

3. Wireless router settings.

Open the browser input refers to any number that is not occupied in the 0 254 range, such as entering the router setting interface, because only the IP of the wireless router can be accessed in advance, click on the LAN port to start setting;

Click Storage and restart the router. The main purpose of the LAN port here is to use the wireless router as a wireless AP.

The wireless router converts the AP mode.

Of course, there is a faster way to make our wireless router into AP mode, so that after setting, you don't need to set other places, you can make the B router become wireless AP mode, and you can imagine the excitement brought by wireless Internet access. The operation is as follows: end

1.Wireless router 1 is connected to the network (WAN port) connected to Tietong

2.Connect wireless router 1 and wireless router 2 with network cables, and plug both ends into their respective LAN ports, and set the LAN IP of wireless router 1 to (LAN interface), then the IP of wireless router 2 is set as the interface).

3.Both Wireless Router 1 and Wireless Router 2 set their own wireless passwords.

4.The DHCP enabled network segment of wireless router 1 can be set to point to the gateway (, set DNS

5.That's it!

Configuration of Router 1:

2. In the WAN port settings, set the current Internet access mode, in this case PPPoE dial-up.

3. Set the basic information of the wireless, change the default SSID to AP1, enable the bridge function, and enter the wireless MAC address of AP2 in the box below.

Router 4, 1 keeps DHCP enabled.

Configuration of Router 2:

2. In the LAN port settings, change the LAN port IP to :, and then click "Save".

3. The WAN port setting remains the default and unchanged.

4. In the basic settings of "Wireless Parameters", change the SSID to AP2, enable the Bridge function, and fill in the MAC address of AP1 in the box below.

5. In the DHCP service settings, router 2 disables the DHCP service. Then click "Save".

The basic configuration of point-to-point wireless bridging is complete. With the wireless client, you can surf the Internet normally whether you are connected to AP1 or AP2!

If you do not want unauthorized users to access our AP, enable the security settings in the basic configuration of "Wireless Parameters", use only the default WEP encryption type, the key format is ASCII code, and the key type can be 128 bits or 64 bits according to your needs, here you choose 64 bits. Password: loveu

The encryption of AP1 and AP2 should be configured, and the configuration is the same for both sides).

1. Turn on the bridging mode between the two routers.

2. The IP address of the second router device itself should not be the same as the first one, it will conflict, but it must be the same network segment.

3. The channel, SSID, and encryption mode should be configured the same.

4. Enter the MAC address of Router B in Router A, and enter the MAC address above the 4 points of attention in Router A.

If you start from the first LAN port and connect to the second WAN to open it, you can change the IP address of the LAN port in the network parameters of the latter one. For example, the first 3 digits can be changed. Then the WAN selects dynamic and that's it.

Yes, our office is connected to the router (TP-link) with the cat, LAN port, WAN port is automatically obtained, DHCP is opened, the address pool is default, and our dormitory has added a wireless router that is also TP-link, but the model is different. Don't access the first-level router first, take a network cable to access the LAN port of the level-2 router, enter different specifications of the router in the browser, see the label on the back), enter the account password (the default account and password of TP-Link are all admin), enter the settings interface, change the LAN port IP to only be different from the first-level route, the default gateway, save and restart the route and then enter the settings interface, set the WAN to automatically obtain, open DHCP, set the address pool to,, Others are not filled, and the wireless settings are set according to the prompts when entering. Set the computer under your level 2 router to automatically obtain and automatic DNS,Finally, connect a network cable from the LAN port of the first-level router to the WAN port of the 2-level router,Plug in the computer to the LAN port of the level 2,You can use it,If you are wireless,Change the name,Set a password,You can enter (do not change the name,It's useless to set the password,You can enter directly)。

In this way, the users who set up the first-level and second-level routes are not on the same LAN. DHCP automatically assigns IP to LAN computers. Routers produced by different manufacturers, the specific parameters are different, but the principle should be the same, this is my recent successful setup steps, I hope it will be useful to you.

The network cable is connected from the wired LAN port (that is, the port with standard 1234) to the LAN port of the wireless router, and do not connect to the WAN port under normal circumstances.

Not what you say.

But why don't you just use a router with its own wireless capabilities, but a wired plus a wireless?

Can't you just replace the wired one with a wireless router?

If not, then you can directly plug in one of the LAN ports of the wireless router directly from the lead of the line, note that it is not a WAN port. This way, your wireless router is used as a switch. Link to the wireless router, set a login password for the wireless, change the name of the wireless, and you can basically use it.

If you are still available, you can change the management account and password of the wireless router, as well as the IP MAC binding.

Wireless bridging requires a wireless router to have this function.

Wireless Router B (to access the Internet through A Wireless Router A), in the network parameters"Set the LAN port"Set the IP of Wireless Router B to.

At the same time, you need to disable the DHCP server function.

Also in the basic settings of the wireless network, the parameters are the same as those of the wireless router A. The channel is best set to . Encryption should be done in the same way as a wireless router.

The SSID is the SSID number of wireless router A. BSSID is the MAC address of wireless router A, which can be scanned to automatically detect the input.

In this way, the bridging of A and B is easily completed, and the setting method of different brands of products is similar.

When you connect the network cable to the LAN port of the wireless router, it is used as a switch, and it is recommended to change the wireless router and the wired router. Or set the wireless router to dynamically obtain the IP address, note that the two routers must not be set to the same network segment, you can one by one.

There are two types of addresses of routers, WAN port address and LAN port address, LAN port address is the management address, regardless of it.

What you need to do is to set the WAN port address of the wireless router to be in the same network segment as the LAN port of the wired router, plug the line into the WAN port of the wireless router, and set the WAN port to static IP mode. Everything is ok

Link mode: R402 dial-up networking, set the network segment: connect one line from the LAN port to one of the WR-740N, turn on the wireless route, and set the password to complete the link.

Management mode: There is a line that can already query all the MAC and IP addresses that go through it to surf the Internet, which has nothing to do with WR-740N, and its role is only to provide port expansion and wireless network signals.

Wireless LAN port, and then turn off DHCP to try.

There are two ways to cascade routers:

1.Change the connection mode of the second-level router, connect the network cable connected to the LAN port of the first-level router and also connect to the LAN interface of the second-level router, at this time the second-level router is used as a switch, there is no need to set the WAN interface parameters, directly connect the network cable to the computer, just log in to set the wireless part of the parameters can be used, the wireless terminal searches for the wireless signal of the wireless router and enters the encryption key, and can be connected and used after verification;

2.Another way is to use the WAN interface of the second-level router, at this time the router is working in the routing mode, connect the computer with a network cable to log in to the second-level router, set the second-level router WAN interface to dynamic IP mode or static IP mode (the static IP address needs to be set according to the login IP address of the first-level router), and then set the parameters of the wireless part. However, it should be noted that the IP address assigned by the LAN of the second-level router must not be in the same network segment as the first-level router, otherwise there will definitely be conflicts;

3.In general, in the case of cascading multi-level routers, the first-level router needs to be set to the route mode, that is, after logging in, enter the WAN interface settings-PPPoe mode, and enter your broadband account and password.