My Samsung washing machine can t get water because the water inlet valve is broken

If the washing machine appears not to get water:

1.Check that the inlet faucet is open.

3.Check if the operation method is correct.

1).Check whether you select the reservation function, and cancel the appointment when the power is off and re-energized.

2).If you do not press the [Start Pause] button, the correct operation method: [Power] [Start Pause].

Note: Water enters after the machine idling and weighing, it is recommended to wait for about one minute).

4.It is recommended to clean the inlet valve filter. Turn off the faucet, unscrew the water inlet pipe connected to the top of the washing machine to the left and remove it, use needle-nose pliers or tweezers to gently take out the water inlet filter from the washing machine inlet valve connection, remove the dirt on it with a brush, rinse it with water, install it back in place, and reconnect the water inlet pipe.

5.The weather is too cold and there is no heating equipment that may cause the faucet or inlet pipe to freeze, you can:

1).Unplug the washing machine.

2).Wrap the faucet in a hot towel and rinse the faucet with hot water.

3).Remove the inlet pipe and immerse it in hot water, and wait for the ice from the faucet or inlet pipe to melt before trying the machine.

6.Turn on the faucet to check if the water flow is small, it is recommended to screw the faucet to the maximum, or contact the property in the community to check the water pressure.

7.Check that the inlet pipe is not bent, which will cause insufficient water inlet.

If the washing machine still cannot enter the water after the above operation inspection, you can apply for repair through the Samsung official website, and the engineer will come to deal with it for you.

After-sales ** maintenance.

1. The inlet valve is damaged.

If it is due to damage to the inlet valve, the treatment method is as follows:

1) Check whether the filter screen of the inlet valve is blocked and whether the inlet valve is damaged, when the two are confirmed to be in good condition, you can use the AC voltage block of the multimeter to measure the voltage of 220V at both ends of the solenoid valve, which proves that the fault is in the solenoid valve itself.

2) Measure the resistance of the solenoid valve coil with an electric barrier, the normal value is that the measured resistance value is infinity, which means that the magnetic inlet valve coil is burned out and the inlet valve needs to be replaced.

2. The water level pressure switch is damaged.

If it is because the water level pressure switch is damaged, the treatment method is as follows:

1) It may also be that the water inlet of the washing machine has reached the rated water level, and the water inlet solenoid valve still does not stop the water intake, in this case, it is generally caused by the damage of the water level pressure switch, which can be judged by blowing air and pressurizing method.

2) Remove the water level switch first, blow air to the pressure switch through the return pipe, and measure the resistance between the two lugs of the water level switch with a multimeter, and the resistance should tend to zero when blowing; When not blowing, the resistance value should be greater than 10k.

3) After inspection, the measured resistance value is always very large and the action sound of the contact in the water level switch cannot be heard, indicating that the pressure switch is faulty and the water level pressure switch needs to be replaced.

3. The water pressure is too low.

If it is because the water pressure is too low, the treatment method is as follows:

When the washing machine does not get water, there is a high probability that the water pressure is a problem. If the water pressure is too low, it may not be possible to allow water to flow into the washing machine, so that the washing machine will not enter the water, and the water pressure needs to be adjusted later.

4. Washing machine failure.

If it is due to the failure of the washing machine, the solution is as follows:

If the above problems are not repaired well, it means that the washing machine is faulty, and it is best to find after-sales service or make an appointment with a professional master to repair it.

There are generally three reasons why Samsung automatic washing machines do not enter water:

One is that the filter screen of the inlet valve is blocked.

The second is that the water inlet solenoid valve is faulty or the plug-in line is not in good contact.

The third is that the water inlet relay on the control board is broken.

1. The filter screen of the inlet valve of the automatic washing machine is blocked;

2. The water inlet relay on the control panel in the washing machine is damaged;

3. The water inlet solenoid valve is faulty or the contact between the internal plug-in lines is poor;

If this brand of washing machine cannot get water, first check whether there is a problem with the water inlet solenoid valve of the washing machine, or whether the water inlet, water pipes and faucets are blocked.

If the water does not enter, it may be that the water inlet valve of the washing machine is faulty, check whether the solenoid valve is in poor contact. Or the water valve filter is damaged or blocked, it is recommended to dredge or replace it. It may also be that the water inlet relay on the control board is burned out and it is recommended to replace it.

The reason for not entering the water may be because the pressure of the water inlet is not enough, because it needs to suck the outside water into the washing machine through pressure, so you can check it or find a maintenance person to deal with the water inlet.

The reason why the Samsung washing machine does not enter the water should be the problem of the water pipe, otherwise there is a little problem with the washing machine, it is best to ask a professional master to come to see it.

The water inlet is blocked, or the water inlet relay is damaged.

1. Check that the drain valve of the washing machine is open.

2. There are foreign objects or more washing slag blockage inside the drain valve, and the drain valve needs to be disassembled for cleaning.

3. Because the washing machine has not been uniformly designed, the parts and components of the washing machine produced by each factory are different. According to the model and brand of the washing machine, you can contact the after-sales service department of Samsung washing machine to repair and inspect the drainage system and drain valve of the washing machine, and clean up the foreign matter or washing residue in the drain valve to eliminate the fault.

The drum washing machine does not enter the water after it is energized, so check as follows: 1. Check whether the faucet is open and whether there is water, 2. Check whether there is water in the drum that has not been drained, 3. Check whether the program switch is set in the washing program, 4. Check whether the glass door of the washing machine is closed, 5. Check whether the water inlet valve is working properly, 6. Check whether the water level switch is working properly.

This may be a malfunction of the inlet valve, as it should. Disassemble the position of the inlet valve to see if there is a blockage? If there is a foreign object in the inside, it will not enter the water in the future, so it is enough to remove the contents of the inside.

1. Check whether the faucet has been turned on.

2. Check whether the water pressure is too low.

3. Check whether the water inlet is blocked by debris, it is recommended to check the water inlet and clean the water inlet filter.

4. After removing the water inlet pipe joint of the washing machine at the machine end, turn on the faucet to check whether the water is normal.

5. Check whether the inlet valve is abnormal.

Reason: 1. It may be because the lid of the Sanyo washing machine is not properly covered and the lid of the Sanyo washing machine is not used correctly. 2. If the inlet valve is faulty, check the solenoid valve to see if there is a problem.

Suggested Treatment:

1. In daily life, Sanyo washing machine is already a household appliance at home, but many careless people always think that there is a problem with Sanyo washing machine, in fact, it is because when the lid of Sanyo washing machine is closed, the lid is not closed tightly, so that Sanyo washing machine does not enter the water, this is not a problem of Sanyo washing machine, but because Sanyo washing machine is not used normally, so it is usually necessary to pay more attention to the cover of Sanyo washing machine, Don't be anxious to think that the Sanyo washing machine is broken because you are in a hurry and did not close the lid of the Sanyo washing machine, and the Sanyo washing machine is not flooded.

2. Sometimes there may be a problem with the water inlet valve, if so, you should ask a professional maintenance personnel to check it as soon as possible, if it is really a problem with the water inlet valve, then let the professional maintenance personnel see how to repair it to make the Sanyo washing machine use normally.

1. You can check whether the power is on, or whether the faucet is turned on, and rule out that the automatic washing machine does not enter the water due to negligence.

2. The filter screen of the inlet valve is blocked.

Solution: Wash the filter, reinstall it, and start the washing machine again.

3. The water inlet solenoid valve is faulty or the plug-in line is not in good contact.

Solution: Contact after-sales, replace the water inlet valve, and repair the plug-in line.

4. The water inlet relay on the control board is broken.

Solution: Contact after-sales for repair.

The solution to a broken water inlet valve in a washing machine is as follows:

1. Check whether the power is turned on, turn on and operate normally, if the washing machine has not started to work, then turn on the power supply to make it work normally;

2. If the door lock indicator light is not on, check whether the washing machine door has been closed, if it is not closed, reopen and close it again before use;

3. If the washing machine door has been closed, press the door handle lock and the door lock light will be on, it means that the question is in the micro delay, and the micro delay needs to be reinstalled, and the position of the door lock should be adjusted;

4. There is dirt blocking the filter screen of the washing machine's water inlet valve, resulting in the inability to enter the water, so you need to remove the filter screen and clean it before reinstalling it;

5. Open the upper cover and check that the inlet valve coil is.

The solution to a broken water inlet valve in a washing machine is as follows:

1. Check whether the power is turned on, turn on and operate normally, if the washing machine has not started to work, turn on the power to make it work normally;

2. If the door lock indicator light is not on, check whether the washing machine door has been closed, if it is not closed, reopen and close it again before use;

3. If the door of the washing machine has been closed, press the door handle to lock it, and the door lock light will be on, which means that the problem lies in the micro-delay, and the micro-delay needs to be reinstalled, and the position of the door lock should be adjusted;

4. There is dirt blocking the filter screen of the water inlet valve of the washing machine, resulting in the inability to enter the water, so the filter screen needs to be removed and cleaned before reinstallation;

5. Open the upper cover and check that the inlet valve coil is.