After the computer failed to reinstall the system, the system could not be imported with a ghost dis

The computer can't afford to bring the W7, try to change the XP.

This prompt is that the hard disk detection failed:

1) SATA wire is not of good quality or is not well plugged in.

Solution: Change the SATA cable or plug the SATA cable into another SATA slot on the motherboard.

2) The hard drive is faulty and may need to be replaced.

3) The BIOS setting is wrong, go to the BIOS to find the BOOT option, and check whether the hard disk is blocked.

4) Try to set the hard disk to boot (whether it is set incorrectly).

After the U disk ghost system, the problem of failure to boot is more common, generally because the main partition is not set as the active partition when partitioning.

U disk can do ghost, then U disk should also have a DOS toolkit. You can use the dos fdisk command to partition the hard disk, or you can set the primary partition to active.

The specific steps are:

Start the computer with a USB flash drive boot and select DOS.

Under DOS, enter fdisk

After the software runs, select 2 to activate the hard disk partition.

Select 1 to activate the first partition, which is the primary partition of the ghost system.

Confirm the exit. Unplug the USB flash drive and restart the system to enter the new system.

If you have PE, you can go to PE and use a partitioning tool such as partitionmagic to set the active partition. In short, the ghost system needs to set up an active partition to boot.

For example, in the figure below, the red circle is the active partition of the two main partitions, both of which have systems and can be booted.

The system must be installed on the primary partition, not the logical partition.

1. It is recommended to choose a 30G-40G main partition to install Win7 system.

2、Use ghost to install win7 and enter the partition in PE。

3、Then select the partition where the win7 system is installed, right-click and select "Activate current partition" and then restart it.

I'm also in this problem.,Reinstalled it 6 times and it's the same.,The last time is to pull out the USB flash drive and then restart the system computer.,Suddenly, it's OK.。 I don't know if it's a problem, because I didn't try it again after installing the system.

Boot file is missing. and no access to the system. A startup disk is required to boot up the computer.

Use DiskGen to rewrite an MBR to your hard drive.

Have you copied the win7 image to the D drive?? That's definitely not going to work, because the D drive is a logical partition, and you can't boot the system without setting it to active.

,You should turn off SATA in BIOS,Probably press F12 when booting up (look at the text displayed below when a screen appears when the computer is turned on),Turn off SATA and then that's it。

Small fire door-to-door manual ghost installation system.

With low cost and stable data storage performance, optical disc is widely used in computer installation, and now there are still many people who use optical disc to reinstall the system, especially the ghost system disc, the ghost system does not need to be activated, and the installation is easy to install, most of the installation discs are ghost discs, so how to use ghost discs to reinstall the system? Let's follow along with the step-by-step tutorial to learn the ghost disc reinstallation system.

1. Reload and prepare1. Configure a computer with a *** optical drive.

2. Ghost system CD: How to make an XP system installation CD.

4. Boot settings: How to set up boot from CD.

2. The steps to reinstall the ghost disc are as follows1. Insert the ghost disc on the computer, press F12, F11, ESC and select *** option during the restart process, and press Enter;

2. Enter the disc installation interface, select Wuqing installation system to the first partition of the hard disk;

3. Go to this interface and perform the ghost system decompression operation;

4. After the reed is decompressed, it will automatically restart and start to reinstall the ghost system;

5. Finally, reboot into the ghost system desktop, and the reinstallation is complete.

That's it for the tutorial of the ghost disc reinstallation system,Just choose to boot from the disc when you boot up,You can easily complete the ghost system reinstallation,I hope it will help you。

Your glitch occurs when the ghost is almost finished, and this situation is usually a ghost problem.

There's also a way you go into dos, format c:

Without parameters, let him pass slowly. Ghost should be fine.

Most of the time it is caused by unstable memory.

Your computer is not constantly getting errors of what memory 00000x000 etc.