How to set up a dlink router to enable two computers to access the Internet at the same time

1。The router cable should be correctly arranged2. First, set the host IP to the IP and the default IP address to see how it is on the router 3.

Look at the IP on the route, open this IP login, admin account, password, are the same, Next, select ADSL, virtual dialing, next, enter your Internet account and password, Next, Complete4. Then change all the local IPs of the computer to Auto 5. If you can only surf the Internet and can't open a web page, just start in the run, type cmd, press enter, and then type ipconfig all to see the two columns of DNS, write those two addresses to your computer's local DNS, and it's OK

Very first check to the mac run cmd and then enter ipconfig all you can see the following physical address is your mac write it down and wait for it to be useful Connect the router and the computer to enter the management interface of the router ( Select network parameters - win port settings Enter the Internet access and password Select the special wave number mode Save In the selection WAC clone Enter the mac you just wrote down in the MAC address Save The router will restart by itself OK Get it and give points.

If two computers go online at the same time, your router settings, generally the router has an IP address on it, generally: or if it is set, the other computer still can't access the Internet, check whether the IP addresses of the two machines are wrong, see if you have selected automatic acquisition, you must automatically obtain the IP Set the automatic IP as follows: Turn on the 'Internet Neighbor--- Local Connection--- right-click the properties--- the following --- protocol --- properties--- select the automatic IP"-- Both computers must be the same!

to be able to access the Internet.

Look at the manual, how to set it up will give you tips! Generally, there is a disc in the router you buy now, and you can use the disk to drive it!

Just find a router to offload.

Categories: Computer, Networking, >> Hardware.

Problem description: I have a D-Link here. There is no instruction manual and outer box. On the back is written:

d-link ether broadband routermodel no.The DL-707P wants to use it to split ADSL between two computers. But I don't know how to set it up.

I would like to tell you how to set it up and how to do it, because there is no manual. The more detailed, the better. Thank you.

Analysis: The first method:

Go buy a network card (30 yuan) a network cable, install it on the main machine, and connect the two computers.

Host settings: ADSL is shared with local connection 1, and the local connection IP is set to:

The gateway is empty. Local connection 2 is set to get automatically.

The other computer is set to get it automatically.

The second method:

Buy a router (about 200), ADSL access route, and then distribute the route to two computers, both are set to get automatically, the setting of the route needs you to follow the manual, and the method of entry is entered in IE:

For admin, so is the password.

You can access the Internet in the form of dual hosts**, but you must turn on the other host to access the Internet.

The host adopts dual network cards, one port is connected to the external network, and the other port is connected to another machine. The host acts as a server.

Method: 1. Hardware installation.

1.When you first set up your home network, disconnect all your devices, including computers, monitors, modems, and routers.

2.Connect the network cable to the network card of each landslide computer in the LAN, while the other end of the network cable is connected to the LAN port in the rear panel of the router.

Tip: The TL-R410 router has a total of 4 ports available to clients, and computers in this LAN can access these ports at will, and there is no order requirement. In addition, there is an uplink port for cascading, generally do not plug into this port.

3.Connect the network cable of the cell broadband to the WAN port on the back of the router.

4.Plug in the power port on the back of the router.

After all the hardware is installed and confirmed, turn on the power and start the computer.

2. Configure a broadband router.

1.Before configuring a broadband router, be sure to learn about the relevant parameters from the technician, because the broadband router provides three Internet configuration modes, namely static IP, dynamic IP and PPPoE mode. If you are using cell broadband, select Static IP for code starter and set the following parameters:

Static IP address, subnet mask, gateway, preferred DNS server and alternate DNS server, in the case of ADSL, you need to select the PPPoE method, and remember your username and password.

For details, please refer to the following article.

baohs/article/pc/technology/2006/06/dp_22902_2

DLINK wireless router to set up multiple computers to access the Internet: Set up router dialing.

How to set up the router].

Home Network Environment Cabling]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- computer 1 and computer 2.

2. No modem: network cable --- router WAN port; The LAN port of the router --- computer 1 and computer 2.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the Internet user name and password according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Before connecting to a wireless router, you must connect a regular router.

The first time you set up a network cable to connect a computer, open the settings page (usually then enter;

Enter the corresponding account and password, generally the newly bought are admin;

Enter the operation interface and open the setup wizard on the left;

Click Next, enter the Internet mode setting, if your home is dial-up, then use PPPoE (dynamic IP can be used by plugging in the network directly on the computer, there is a DHCP server on the upper layer, the static IP is generally a private line or something, it may also be a cell bandwidth, etc., there is no DHCP server on the upper layer, or if you want to fix the IP, I choose PPPoE because I dial up);

If you choose PPPOE dial-up Internet access, you need to fill in the Internet account and password; Then the next step is to enter the wireless settings, channel, mode, security options, SSID, etc., generally SSID is a name, you can fill in as you like, and then the mode mostly uses 11BGNFor wireless security options, we need to choose WPA-PSK WPA2-PSK, which is so safe, so as not to let people hack and rub the network lightly;

The next step is complete.

If you can go online directly through the router, it should be wireless has not been set up, the computer opens the browser, the address bar is entered, the username admin, the password is not, after logging in, click advanced - advanced wireless, modify the wireless mode to G B mode, cancel the short security gap. Then go to the installation - wireless installation - manual wireless Internet installation, change the wireless network name SSID (in English or numbers), modify the wireless channel to 11, turn off WMM, and use WPA WPA2 enhanced encryption. After saving, use the computer to search for wireless signals, enter the password to connect, and try again, noting that the computer must also have a wireless network card to access the Internet wirelessly.

The router manual is there, you just need to install the manual step by step, it's actually very simple.

It's a long story to set up the problem. Why don't you buy another switch?

In fact, the simplest is: ** line to the cat, the cat to the router win port, any one of the other lin ports of the router (there are 7) to the switch, and the switch to each computer. When you connect like this, you form a small local area network.

Then use any computer to enter most of this address in IE, you can also read the router's manual), enter the username and password in the pop-up dialog box to enter the router, put your broadband account in the router, the password into pppp0 dial-up, and then customize a gateway address in the LAN settings after successful connection, for example, and then exit, put your computer manual IP, any one, the mesh is, and the following DNS is also. Other computers are manually assigned IPs. In this way, those who have IP can access the Internet, and those who do not have IP can not access the Internet temporarily, and there are many ways to control it, and I am just the simplest here.

The equipment provided by telecom can only be used at home, so the hardware is limited to only 2 computers, and other subsequent connections are prohibited from accessing the Internet.

1. You must connect the cable out of the cat to the WAN port of the router, that is, the Internet port, and then set the account and password of PPOE dialing in the router and save it, let the router help you dial, and then turn on the router DHCP service;

2. If the cat still limits the number of machines, then you can use the router MAC address cloning method to copy the MAC address of one of the computers to deceive the router, so that other computers can access the Internet, the router's own IP is still the default, and the IP address and DNS of other computers are automatically obtained;

3. Your router or cat is too old to judge the direct connection or crossover line, try to connect the router WAN port or you call the Internet port between the cat and the crossover line.

The 2 ** wires that came out of the separator have been connected correctly! Now your most important question is: the cat has another wire (that is, the network cable) out of the inter hole to connect to the router, not any hole, this is very important!

Next, go to the router to set it, the default username and password is admin, and set your organization's broadband account and password to the router. The connection between the router and the switch is what you are. Finally, your unit's computer no longer needs a broadband connection, and you can directly access the Internet.

Definitely 10 units are easy to use. It may be easy to set the IP and DNS of some computers to be obtained automatically. I'm a computer fixer, and there's no mistake.

The solution actually starts with the hole you said you couldn't connect.

The line out of the cat is connected to the routing Internet port (commonly known as the WAN port), and then other lines are connected to the computer, if there are too many computers, a line is routed out of a switch to continue to divide the line.

Then the point is that you can't dial through the computer, you have to log in to the router, configure the PPPOE dial-up of the WAN port according to the manual, and then configure the automatic connection, and it's OK.

If your dial-up requires a special client or special authentication must be connected by a computer, then sorry, this solution can only be invalidated.

It seems that the route is blocked, so only two can get on.

Router B is connected to the pre-router A as a secondary router, and the LAN port of router A separates a network cable to connect to router B, which can be achieved in two ways:

1: Connect to the WAN port of B, and the two routers are cascaded.

DHCP is enabled on Router A, dynamic IP address is set to Router B, and the LAN gateway of Router B is not on the same network segment as A to avoid IP conflicts. For example, if the gateway IP of A is A, then change the LAN port gateway of B to at least one of the first three digits that is different from that of A.

The wireless settings of the router are set according to the manual. After the settings are complete, the LAN port of Route A is connected to the WAN port of Route B.

2: The LAN port of A is connected to the LAN port of B, and the B router is used as a switch

Connect to the LAN port of Router B, disable the DHCP function of the LAN port of Router B, enable the LAN port setting of network parameters, and change the IP address of the LAN port so that Router B and Router A are on the same network segment. For example, the LAN port IP of router A is changed to B, as long as it does not conflict with other IP addresses that have been used. The WAN port parameters do not need to be set, and the wireless settings of the router are set according to the manual.

After the setting is complete, the LAN port of route A is connected to the LAN port of route B, and route B is equivalent to the expansion port of route A, which plays the role of a switch, and the computer can be connected to the LAN port of route B.