How to set a password for a router, how to set a password for a router

Look at the IP behind the router in general.

The password is also behind it, and it's usually admin

Then you can set it up inside the wireless security.

With the upgrade of the network, the router is becoming more and more important, because the router can allow many computers to share the Internet together, which can save a lot of resources, but if you don't set the router password, it is easy to be stolen by others. Method.

The specific operation of setting the password of the router:

Step 1: For the problem of setting a password on the router, first right-click "Online Neighbor" and select "Properties".

Step 2: Right-click "Local Connection" and select "Properties".

Step 3: Left mouse button click "Internet Protocol" and left mouse click "Properties".

Step 4: Click the left mouse button "Use the IP address below" and follow the input address in the figure. DNS can be set according to the local NDS.

Step 5: Click OK with the left mouse button.

Step 6: Double-click IE with the left mouse button.

Step 7: Enter in the address"Account password"Left-click OK.

Step 8: Click the "System Bucket Removal Tool" with the left mouse button and select "Modify Login Password".

Step 9: Enter the original "Account Password" and then enter the new "Account Password", and click "Save" with the left mouse button.

At this point, the router password is complete, everyone come and set the password for your router!

I don't want others to feast on their own. wifi,You should set a password for the router,The following is how to set a password for the router,Welcome to refer to reading!

Tools Raw materialsWireless routers.

Computer. Step MethodMake sure that the Wi-Fi network is connected, which can be seen in the status bar.

You can enter the router settings page.

There will be a login prompt before entering,The normal default is:admin,The password is also set in the wireless router of admin piggy,"Wireless settings"Wireless security settings"。 Some routers will have security settings in them.

Going to the wireless security settings, in addition to the option not to set a password, there are also 3 encryption methods:

WPA-PSK WPA2-PSK - This mode is used by general users, which is relatively secure and can prevent attacks by general network stealing software.

wpa/wpa2wep

1. First connect the WAN interface of the router, and then you need to connect the mobile phone to the WiFi signal of the router, as shown in the figure below.

2. Open the browser in the mobile phone, enter it in the browser, you can open the management page, and then set an "administrator password" according to the page change and prompts, as shown in the figure below.

3. At this time, the router will generally automatically detect the "Internet mode", and only need to set it accordingly according to the detection results. If it is detected that the "Internet access mode" is: broadband dial repentance number to go online, you need to fill in your home's "broadband" and "broadband password" below, as shown in the following figure.

4. After setting the Internet access mode, set the WiFi name and WiFi password of the router, as shown in the figure below.

5. Click OK to complete the setting, some routers may need to click the "Finish" button before liquidation.

How to set a password for a directive router

(1) How to set a password

Router>enable into privileged mode.

router configure terminal into global mode.

Router(config) enable passwordcisco to set privileged passwords.

router(config)#ex

router write memory to save the configuration file.

The password is set at this point, and you can try to see if the password is set successfully.

(2) How to change your password

Restart the router and press CTRL+C to enter the following modes during the reboot.

router1 >confreg ox2142 ignores the configuration file in nvram and skips the original password.

Router2 >reset to reboot the system.

continue with configuration dialog?[yes no]: no Manually configured.

router>enable

router copy startup-config running-config copies the configuration file from nvram to memory.

router(config) enable password 123456 reset the password.

router write memory to save the new configuration file.

router reload reboot the system.

Press CTRL+C during the restart process

router1 >confreg ox2102 reloads the configuration file from NVRAM.

Router2 >reset restarts the system and changes the password successfully.

How to set a password for an interface router.

Right-click on "Net Neighbors" and select "Properties".

Right-click on "Local Connection" and select "Properties".

Left-click on Internet Protocol and left-click on Properties

Left-click on "Use IP address below" and follow the input address in the image. DNS can be set according to the local NDS.

Left-click OK.

Double-click Internet Explorer with the left mouse button

Enter in the address "Enter.""Account password"Left-click OK.

Left-click System Tools and select Modify Login Password

Enter the original "Account Password", and then click "Save" after entering the new "Account Password".

Here is how to modify the "wireless password", after the modification, you can save and restart the route directly in the next step!

Here's how to set it up:

1. Turn on the wireless router, then find the name of the router in the wifi settings of the mobile phone and enter the password;

2. After successful connection, enter the router gateway address in the browser address bar of the mobile phone;

3. Then the interface that needs to enter the login username and password will pop up, this username and password are the bottom label of the router will also be identified, and some default usernames and passwords are admin;

4. Choose broadband dial-up, fixed IP or automatic IP access and other Internet access methods according to your own broadband, if it is dial-up, you also need to enter [Internet access] and [password].

5. Find [PSK Password] in the security settings, generally select WPA-PSK WPA2-PSK encryption method, and enter the connection password of the router; After entering, click the [Save] button at the bottom of the page, this password will be your wifi connection password in the future; Then you need to restart and use a new password to connect to the wifi;

6. You can also set the username and password to log in to the router management page, which can also be saved and restarted after entering.

Here's how to set a password on your router:Tools: Dyson Lead K550, Win11, browser version.

1. First open a browser, enter the IP on the back cover of the router in the browser address location, and then press the enter button.

2. Then the wireless router login interface will be opened, if it is the first time to log in, enter the password behind the wireless router, if it has been set up password Zenqiao, enter the previous password.

3. Then on the interface you enter, click the [Router Settings] on the left side of the He Chun button option.

4. Then on the page that opens, click the [Change Management Password] option.

5. Then enter the original password, new password, confirm password and click OK.

6. Finally, it will prompt that the new password has taken effect, which means that the router has successfully changed the password.