The washing machine is dehydrated for too long, if it is manually dehydrated, that is, suddenly pres

Yes, it will hurt the washing machine, but it will start the motor brake, which will affect the life of the motor.

The motors of the washing machine are all brake motors, and the motor itself has a brake device linked to the door. At the time of dehydration, as soon as the signal of the door is opened, the brakes will be activated, and the motor will be locked to prevent it from spinning.

This is the designer considering that the inner cylinder rotates at high speed, and once a foreign object enters the inner cylinder, it will damage the inner cylinder or run out, and the high-speed object will hurt people or objects, or the hand will accidentally reach in, which will harm personal safety. Therefore, no matter how often it is used, the brakes will wear out, and the motor itself will be damaged.

Have you used the brakes? Press pause when throwing water, the washing machine will stop slowly, the process of stopping is the same as the end of the program, there will be no harm.

Spit it out, the automatic washing machine is indeed too long, some even dry for 7-9 minutes in a row, in fact, it is enough to reach the maximum speed of 30 seconds, and this design is also made behind closed doors.

It should be said that there is no big impact, because the rotation of the washing machine is powered by the reducer and the belt to the wave wheel and the inner cylinder, and when you open the upper cover, the power supply of the motor stops, and the brake band of the reducer does not have a braking force to lock. It's the same as when we slow down a moving car, so it doesn't have much of an impact.

At this time, the washing machine will brake sharply through the motor, and the drum will be connected to the motor through the belt, so that the emergency stop will first be bad for the belt and will accelerate the wear, and secondly, the current through the motor during the sudden braking will be very large, and it is not very good.

You won't use a lot of electricity for a few more minutes, so if you're not in a hurry, just follow the default time.

Of course, the team washing machine has a lot of damage: the clutch if it is operated so for a long time, back to the great.

Reduced lifespan. It is recommended that you do not do this.

No, it's the same principle as normal stopping.

z This definitely has an impact on the washing machine 3, the clutch is easy to break!

The impact is not large and can be ignored.

Yes, suddenly pressing the washing machine will suddenly brake sharply, and then you will hear a bang.

After washing the clothes, the sand step of dehydration does not move, what is going on.

Hello dear, I have seen your question, and I am working hard to help you sort out the answer, please wait a minute or two, thank you very much!

The reasons why the washing machine does not automatically jump to dehydration after washing are as follows: 1The washing machine panel door is not closed well or the switch of the top cover is damaged, it may also be that the switch is in poor contact, the washing machine is not allowed to open the top cover because it is a high-speed action when dehydrating, so there is a linkage switch on the top cover, and the cover circuit will be automatically disconnected as soon as the cover is opened.

If it is damaged, it will not move. 2.The drainage system of the washing machine is blocked or the drain valve is broken, the washing liquid in the water cylinder cannot be discharged, or there is too much foam in the water cylinder, the washing liquid in the cylinder is difficult to drain for a while, the water level switch cannot be reset, and the washing machine cannot enter the dehydration program.

3.The drain valve does not pull the clutch conversion apart, and the washing and dewatering of the automatic automatic washing machine is completed by the gear at the bottom of the solenoid valve conversion, and the damage of the solenoid valve will also make the dehydration unable to operate normally. 4.

The washing machine is not placed smoothly, regardless of whether the ground is flat or not, the washing machine should be perpendicular to the horizontal surface. 5.The laundry in the bucket is not evenly arranged, so the laundry should be placed evenly around the bucket before dehydration.

6.If the boom on the bucket is inconsistent or the spring spring is inconsistent, the spring should be adjusted or replaced. 7.

Since the washing machine is placed a little low at the back, put something under the two legs in the back to make it a little higher than the front, and the problem is solved. 8.Poor motor performance and capacitor problems lead to insufficient output power, which can be solved by replacing the capacitor.

9.The tightening screws of the inner barrel of the washing machine are loose, or the bottom bracket of the inner barrel of the washing machine is damaged. If this is the case, in most cases, an empty washing machine can be dehydrated.

10.The washing and dewatering of the fully automatic washing machine is done by converting the gears at the bottom of the solenoid valve, and the damage of the solenoid valve will also make the dewatering unable to operate normally. 11.

It is possible that the rubber belt is loose.

<> the washing machine can be stopped suddenly when it is dehydrated, but this operation will start the motor brake, which will affect the life of the motor.

The motors of the washing machine are all brake motors, and the motor itself has a brake device linked to the door. When dehydrating, as soon as the signal is given that the door is open, the brakes are activated and the locking motor no longer rotates.

This design is to take into account the high-speed rotation of the inner cylinder, once a foreign object enters, it will damage the inner cylinder or after the foreign body escapes, the high-speed object will hurt people or objects, or the hand accidentally reaches in, will harm personal safety.

This behavior is not recommended to be tried often, it is easy to wear out the brakes, and the motor itself can be damaged.

The washing machine stops as soon as it is dehydrated, and the reasons are as follows: 1. Check the water inlet valve of the washing machine and whether it is open. If it is not opened, please close the inlet valve with silver.

Then press and hold the button of the water inlet valve with your hand to let the water flow out; If you still can't solve the problem, you have to contact the maintenance master for on-site maintenance. 2. If it is a fault caused by the blockage of the drain pipe of the washing machine, you need to dredge the sewer pipe. 3. There is also a situation where the washing machine itself fails and the dehydration function fails, which is generally caused by motor damage or short circuit of the line.

It is recommended to contact the manufacturer's after-sales service personnel directly for maintenance!

Hello, dear, there are four main questions to answer for you: 1The capacitance capacity decreases, and the starting distance is insufficient; 2.

Local short circuit of motor coil, distortion of magnetic field; 3.The brakes become tighter or the shock absorber and waterproof place is dry, which increases the load; 4.The lower part of the dehydration bucket has a clump of clothes entangled or the water is not drained.

Or check whether the water is stopped during laundry or the water pressure is too low to cause the water inlet to overtime, whether the drain pipe outlet is too low, and the highest place is required to be 80-100cm above the ground; Check if the rinse or dehydrator knows that the machine stops and the water does not drain, and it is recommended to clean the filter. The user first eliminates whether the anti-wrinkle soaking function is selected, and presses the anti-wrinkle soaking button to dismiss this function.

Summary. 1. Check whether the water is stopped during washing or the water pressure is too low to cause the water inlet to be overtimed, and whether the water outlet of the drainage pipe is too low, and the highest place is required to be 80-100cm above the ground;

Hello, glad to answer for you.

1. Check whether the water is stopped during laundry or the water pressure is too low to cause the water inlet to be overtimed, and whether the water outlet of the water outlet is too low, and the highest place is required to be 80-100cm from the ground;

2. Check whether it is stopped during rinsing or dehydration, and the water cannot be discharged, it is recommended to clean the filter;

3. Whether the user has selected the anti-wrinkle soaking function, press the anti-wrinkle soaking button to release this function.

The washing machine spinning has been stuck at that 2 minutes, there may be many reasons, we can consider from the motor, transmission system, control system, electronic control, etc.

1) Motor: If the motor of the washing machine fails, it will not work normally, that is, it will stay in this state for 2 minutes.

2) Transmission system: The failure of the transmission system may cause the washing machine to not work properly, resulting in the washing machine staying in this state for 2 minutes.

3) Control system: The control system may be faulty, which will affect the number of ants in the washing machine to stay in this state for 2 minutes.

4) Electronic control: There can also be problems with electronic control, so that the washing machine cannot operate normally and stays in the state for 2 minutes.

In short, in order to find out the reason why the dehydration of the washing companion rock coat machine has been staying for 2 minutes, it needs to go through detailed inspection and investigation to find out the specific cause of the failure, so as to carry out effective maintenance.

A semi-automatic washing machine may have a broken timer, just change the timer.