-
Anonymous users2024-02-05Connect the network cable from the cat with the WAN port on the router, and connect the computer with the network cable to the user terminal on the router. After connecting, enter it in the browser, and you can open the router interface. The username and password are generally admin, and you can enter your broadband username and password after entering, and the router will be turned up at the most.
-
Anonymous users2024-02-04The router is tplink! That's easy! You're right, too.,Just connect your own interface to the other 4!
Then open your computer IE browser and enter it to configure the router! In fact, you only need to enter the username and password of the telecom in the WAN port configuration, and your own companion is OK.
-
Anonymous users2024-02-03**The cable is connected to the cat, the network cable on the cat is connected to the main port on the switch, and the computer can be connected to other ports.
This problem may be a problem with the network cable, see if one of the 4 lights behind the cat is flashing (normal), the switch light is flashing, and if the network cable behind the computer is connected, a red light is on and a yellow light is flashing.
-
Anonymous users2024-02-02That's only possible, that is, there is a problem with your network cable, the general computer is connected to the router, as long as the router is powered on, the computer will not appear x, you check your network cable.
-
Anonymous users2024-02-01See if the LAN light of your computer's corresponding router is on, if it doesn't, it may be a problem with your network cable or your network card or router.
-
Anonymous users2024-01-31The land rover is not powered on??? If it is bad, it will be displayed on the mouth of the land rover
-
Anonymous users2024-01-30Connect the router to the computer, go to the router web page, and set the router IP.
-
Anonymous users2024-01-29With a switch is cheap and you don't have to set it up because there are already routes.
The router needs to be set up.
-
Anonymous users2024-01-281. Connection: **The "LINE" interface of the cat is connected to the "LAN" interface of the cat, the "LAN" interface of the cat is connected to the "WAN" interface of the router with a network cable, and the LAN 1, LAN 2, LAN 3 and LAN 4 interfaces of the router are connected to each host.
2. Set the IP and DNS acquisition method to automatic. Right-click the Local Connection property Network Internet Protocol property, and the upper and lower points will be automatically obtained.
3. Check the IP address at the bottom of the router like ", enter the IP address you see in the browser address bar, log in to the router settings interface, fill in the username and password of the login interface "admin", and then follow the Chinese prompts to enter the account and password.
4.The signal of a wireless network can be affected by a variety of factors, so it is normal for the speed to change
And there won't, e-mail me.
-
Anonymous users2024-01-27Use the cat to connect the WAN port of your wireless route,Wired Internet computer connection 1-4 port which,Then use the wired computer to log in to the management interface of the route to set up,Enter this is generally the default gateway in the address bar of the IE browser,If it doesn't work, you have to trouble a little bit,Enter cmd in the start - run - ipconfig,Look at the address of gatway (that) The username and password are generally admin,If not, you can read the manualOnce inside, you can set up wireless Internet access.
-
Anonymous users2024-01-26The cat is connected to the WAN port of the wireless router.
Then enter the route settings and it's OK.。。
-
Anonymous users2024-01-25Did you just buy a router? The service is missing, the general boss will set it up for you, call ** ask the boss, this is the most practical! Hehe......I am a corporate network engineer in my business.
There are two situations, first: your computer is poisoned by ARP, as soon as you start the Internet virus, trick other computers into sending data packets to your machine, and your computer throws away these packets, their computer will not be able to get on, use 360 to kill the virus. >>>More
From the LAN port of the main router, a network cable comes out and connects to the LAN port of the wireless router, log in to the wireless router, turn off the DHCP service of the wireless router, and set the IP address of the LAN of the wireless router, which should be different from the LAN IP of the main router.
If you want to let 10 machines access the Internet, you can set up a fixed 10 IP in the router to access the WAN port, you can access the Internet, and the other 20 machines can access each other as long as they are in the same IP segment as the first 10 machines. The features you mentioned can be perfectly fine. There will be technical support for how to set up the route you procure. >>>More
As the main router that uses the account virtual dial-up to access the Internet, WDS cannot be enabled, and the secondary router enables WDS to tick, and the bridge password method and password must be the same as the wireless security password method! That is to say, during the bridging process, the router needs to enter the password in 3 places, namely: 1, the wireless security settings of the main router, 2, the bridge security settings of the secondary router, and the wireless security settings of the 3rd secondary router. >>>More
Turn off the DHCP in the DLINK router, and then change his IP, don't be the same as the Tengda router, and set up each computer to automatically get the IP!