Mercury router wireless bridging setup issue

As the main router that uses the account virtual dial-up to access the Internet, WDS cannot be enabled, and the secondary router enables WDS to tick, and the bridge password method and password must be the same as the wireless security password method! That is to say, during the bridging process, the router needs to enter the password in 3 places, namely: 1, the wireless security settings of the main router, 2, the bridge security settings of the secondary router, and the wireless security settings of the 3rd secondary router.

The 3 security authentication methods and passwords must be the same! This way the passwords don't get mixed up (which I set up this way), or the secondary router bridge security settings are the same as the wireless security settings of the primary router (it has to be dropped!). ), the wireless security password of the secondary router can be different (I haven't tried it).

In the old 54M routers, there was no "scan" option, but there was a WDS option, so you need to interfill the MAC, but in the bridging mode, the security authentication mode is only Web. The frequency band can be automatic. The primary route is dhcp:

Must be enabled! DHCP cannot be enabled for secondary routes except on a network segment.

Because there are too many connection layers, it is best to use wired connection for multi-layer bridging, and the IP address needs to be set to be different to avoid gateway conflicts, and only one DHCP is left in the network.

It's like the wind takes away only a grain of salt.

Another way of suffering, an adventure, great philosopher. Still, it's okay: on the Neva River.

Be a new woman to yourself, what is a cage?

His tears are nothing, haha.

1. Enter the first router and select the wireless parameters Basic Settings Turn on the bridge function MAC address of AP1: MAC address of the current router MAC address of AP2: MAC address of another router. .

1. Turn off the DHCP server, if the DHCP of the secondary router is enabled, the computer may get the wrong gateway address, resulting in the inability to access the Internet, so you need to close the DHCP server of the secondary router. Setup method: Log in to the management interface of the secondary router, click Advanced Settings >> Network Parameters >> DHCP server, select DHCP server as OFF, and click Save.

2. Modify the LAN port IP, if the management IP address of the primary and secondary router is the same, it will cause IP address conflicts, resulting in the computer being unable to access the Internet, so you need to modify the management IP address of the secondary router. Modification method: Log in to the secondary router management interface, click Advanced Settings >> Network Parameters >> LAN port settings, select LAN port IP address setting to Manual, and modify the IP address of the secondary router (the settings are in the same network segment as the primary router and do not conflict with other computers, such as the main router, the secondary route Verlinker can be modified to, and click Save after the modification is completed.)

3. Confirm that the terminal automatically obtains the IP address and DNS server address, and obtains the IP of the same network segment as the router, and the gateway is the management address of the main router. If you don't know how to set up your computer's IP address, please refer to: How to set your computer's IP address to be automatically obtained.

If the computer has automatically obtained the IP address of the bridge, but the IP address obtained is, please disable the local connection or wireless connection corresponding to the computer before enabling it.

4. Internet access control, please check whether the Internet access control is enabled on the main router to restrict the corresponding computer from surfing the Internet. It is recommended that you change the rules or disable the Internet access control for the time being.

5. ARP binding, the main router sets the IP and MAC address binding to prevent ARP spoofing, and you can turn off the ARP binding and try to surf the Internet.

1. Go to the router background and select the network parameters. Guess.

2. Change the IP address to the IP of the same segment of the target network (if the IP of the target network is, change the IP to the last digit differently).

3. After the change, you need to restart the router, confirm it all the way, and wait for the restart to be successful.

4. After the restart is successful, go to the wireless settings Suiyin Destroyer, basic settings, turn on the WDS selection, and click Save.

5. In the pop-up window, select the wireless network you want to connect to, and click the link.

6. Here you need to modify the channel to the same, if you have a password, you need to select the key type, and then fill in the password in the key field, and click Save.

7. After the restart is successful, if the setting is fine, the WDS status will be displayed as successful.

8. Find the DHCP server, DHCP service, select not to enable, and click Save.

9. Restart the router, and you can surf the Internet when you are done.

The steps are as follows:

1. Connect the purchased Mercury router to the data cable, and then connect the computer to the router just now, and there will be wifi after powering on.

2. Then open the browser on your PC, such as Internet Explorer, and type "Enter" in its address bar.

3. Enter the router interface, select "Advanced Hidden Settings" and click "WDS Wireless Bridge".

4. After completing the above operations, select "Next", and the list will appear to find the wifi you want to connect, and then next.

5. Finally, you need to enter the password, after saving, if you see that the WDS has been connected, it means that it has been successful.

1. Enter the Mercury router management page in the browser and click Advanced Settings at the top.

2. Click on the WDS wireless bridging option under Wireless Settings, and click on the main router to select the one you want to bridge.

3. Enter the wifi name and password of the main router to connect.

This article takes Mercury MW325R wireless router & ASUS Tianxuan FA506IV as an example for Windows 10 system browser version.

The steps of the Mercury router wireless bridging method are:Operating environment: ASUS Tianxuan FA506IV, Windows 10, browser.

1. Enter the Mercury router management page in the browser, and click Advanced Settings above the Return Attack.

2. Click on the WDS wireless bridging option under Wireless Settings.

3. Click to select the primary router you want to bridge.

4. Enter the wifi name and password of the main router.

Introduction to the Mercury Router:Mercury Router is a router Pinzenchang brand, with a powerful leaky sock function, is a CPU processor network dedicated processor, belongs to the WAN port 2, and the processing efficiency is 5,000 online sessions.

Bandwidth aggregation is supported. Two WAN ports provide flexible configuration and application for enterprises, and there is a lot of room for bandwidth growth. Multiple ADSL can replace optical fibers, and aggregation lines can increase bandwidth and replace bandwidth upgrades.

Wireless Bridging Method for Mercury Dust Cavity Router Steps:

1: Click Advanced Settings.

In your browser, go to the Mercury Router Management page and click Advanced Settings at the top.

2: Click WDS Wireless Bridge.

Click on the WDS Wireless Bridge option under Wireless Settings. Blind brother empty.

3: Select the primary router.

Select the primary router you want to bridge.

4: Enter the wifi name and password.

Just enter the wifi name and password of the main router.