How do I move an air conditioner? How to move the air conditioner?

1.The refrigerant** needs to be collected, no matter what time the air conditioner is moved, the refrigerant in the air conditioner needs to be collected into the outdoor unit before the air conditioner is disassembled. The specific method is as follows, first turn on the air condition, adjust the refrigeration condition, run for about 10 minutes, use a wrench to unscrew the cap on the interface between the liquid pipe and the gas pipe of the outdoor unit, and quickly close the shut-off valve of the high-pressure pipe (thin).

After a while, you can see the condensation outside the pipe, so you should quickly watch the low-pressure pipe (thick) cut-off valve, turn off the air conditioner, unplug the power supply, and tighten the safety cap, so that the refrigerant is completed. For the case of moving the machine in winter, it is also necessary to cover the temperature sensor probe of the indoor unit with a warm towel. 2.

To remove the indoor unit, the indoor unit of the air conditioner needs to be detected next, use a wrench to unscrew the connecting lock nut of the indoor unit, and use a sealed sodium to screw the silk pattern of the connecting joint of the indoor unit. The control line needs to be removed using a cross, pay attention to the order of dismantling, and install it in reverse order. The internal hanging board is very strong, and it takes a little effort to make it.

3.Dismantle the outdoor unit, the outdoor unit must be safely dismantled, because most of you are at high altitude, use tools such as wrenches to dismantle, and the unloading should be paid attention to stability, without vibration or bumps. For the takeover, it needs to be protected, so that dust can not get in.

Installation, to the new environment, you need to install the air conditioner, the order is first the indoor unit, then the outdoor unit, then the thick and thin pipes are connected, the thin pipe gate is opened with the inner corner, and finally the power is connected.

Do you know how to move an air conditioner? The relocation of the air conditioner to collect fluoride is the key, and the great god teaches you how to collect fluoride.

How do I move an air conditioner? Air conditioner relocation method and steps

Air Tanzi Shifter is a professional air-conditioning technology work, seemingly simple air-conditioning relocation work, in the hands of different air-conditioning personnel have different operating results. So do you know how to move the air conditioner in hail? Let's take a look at the methods and steps for moving the air conditioner.

1. How to move the air conditioner?

1. Preliminary preparation:The relocation personnel came to disassemble the machine and brought a complete set of tools and safety equipment.

2. **Refrigerant:First of all, the machine is cooled, and the small valve is closed after the external machine is running, and the large valve is closed after the valve frost melts away, and the machine is shut down immediately. Pull off the power supply and tighten the safety cap so that the refrigerant in the air conditioner moves the machine to collect into the outdoor unit.

3. Dismantle the indoor unitWhen disassembling the indoor unit, condensate should be prevented from flowing into the circuit board;

4. Disassemble the outdoor unitWhen disassembling the outdoor unit, pay attention to balance while disassembling to avoid vibration and shaking, and finally wrap it in plastic for easy handling.

5. Installation:When the air conditioner is reinstalled, attention should be paid to the installation location and convection. Finally, use detergent to detect leaks, observe whether there are bubbles coming out of each joint, and after verifying that the system is indeed leaking, tighten the valve safety cap.

2. Precautions for air conditioner relocation:

1. Test whether the functions of the air conditioner are working normally before moving.

2. ** Refrigerant, remove the indoor and outdoor connection lines. It is best to mark both ends of the connecting wire, so that there will be no failure caused by the wrong connection of the connecting cable during installation.

3. In the process of handling and installing the external machine, it cannot be turned over, the inclination angle is too large, and the stop valve lift should not be grasped by hand.

4. Whether the terminal block or other wiring places are loose to prevent ignition or other hidden dangers, whether the wire is aging, if there is aging, it must be replaced.

5. The old air conditioner should not be restarted within 3 minutes after it is shut down, otherwise it is easy to burn out the compressor. The new air conditioner has a circuit that prevents the unit from being restarted within 3 minutes, and even if the unit is restarted within 3 minutes, the compressor will not work.

Follow the steps below and stay safe! The relocation installation and treatment are not necessary for vacuuming and ammonia.

1. Disassembly: 1: Turn on the air conditioner and refrigerate the mode. (so that you can collect R22).

2: Open the lid of the two copper pipes connected to the outer machine, and the inside is made of imperial hexagon.

3: First lock the small copper pipe with the hexagon inside, wait for about 1 minute for the small air conditioner (wait for about 2 minutes for the larger air conditioner), touch the temperature difference of the high and low pipe (thick copper pipe) by hand to see if it is close, when the temperature difference of the high and low pipe is close, close the high and low valve and stop the machine.

4: After confirmation, pull out the power supply, loosen the copper pipe with a wrench, and remove the power cord of the external machine.

Note that after dismantling, the interface should be sealed to prevent dust and other impurities.

2. Installation: 1To connect the air conditioner well, the main thing is to tighten the connecting pipes of the internal and external units, and pay attention to the connection to prevent refrigerant leakage.

2.Use the hexagon switch to hit the automatic air conditioner to work normally, open the high-pressure valve (thin pipe valve), and use the hexagon to resist the fluoride port thimble (the fluoride port is on the low pressure), (so that the gas inside can be felt with your hands, and the gas cooler than the air can be closed when the gas comes out, about 10 seconds, not too long, so as not to run too much.) This allows the air inside the line to escape.

3.Then open the valves of high and low pressure, and connect the power cord of the internal and external units.

Note: The connecting pipe is copper, and it cannot be coiled into a dead bend, otherwise it will affect the flow of refrigerant, resulting in the inability to cool and heat.