Windows doesn t start properly. When I reinstalled the system, the result showed that the hard disk

Reload. Reinstall the display shows that the hard disk cannot be found, it may be your SATA hard disk, first boot the computer and press F8 to change the BIOS (F2 for notebooks), and change the hard disk to compatibility mode.

Then find an installed version.,Or install a ghost disk with a sata driver.,There's a lot of this tutorial.,Don't say much.。

Turn on the computer, press del to enter the CMOS settings, and select "Integrated Peripherals-Onchip IDE Device-Onchip Serial ATA Setting", which is the relevant settings of SATA hard disk, which has three options: "SATA mode", "on-chip serial ata" and "serial ata port0 1 mode". The default value of SATA Mode is IDE, that is, SATA RAID is not enabled, and only when SATA Mode is set to IDE, On-chip Serial ATA and Serial ATA Port0 1 Mode can be selected. "On-chip Serial Ata" is the mode in which the SATA controller is selected

1. disabledDisable SATA device, default value. When using SATA hard drives, this option should be enabled; 2. Auto, which automatically detects the presence of SATA devices by BIOS; 3. Conbined mode, SATA hard disk is reflected to IDE1 or IDE2 port, simulated as IDE settings, at this time, you need to select a location in "Serial ATA Port0 1 Mode" to enable SATA device; 4. Enhanced Mode, allow all connected IDE and SATA devices, support up to 6 ATA devices, and set a SATA device as the main SATA device in "Serial ATA Port0 1 Mode"; 5. SATA only, only SATA devices can be used.

Check whether the motherboard capacitor has a burst or drum, my computer had a similar failure a few days ago, and the motherboard capacitor burst out of the computer and turned on the computer to display a very sorry. We have inconvenienced you ... Aren't there several modes in the back?。。 Prompt.

It is recommended to open the coffin for autopsy, equipment problems.

Reinstall the system to see if it is not good, it may be a failure of the memory or hard disk.

Win11 is the latest operating system launched by Microsoft. Many netizens are very curious about win11 and want to reinstall and use it, but some netizens have encountered problems with leakage in installation. If win11 installation can not find the driver?

Installation requires the installation of drivers. If there is no driver to choose from, it may be because we do not have the corresponding processor driver installed. The specific solutions are as follows:

Method 1: 1First of all, we reboot the computer, use the hotkey to enter the BIOS settings when booting up, and then press quotf7 quot; Or click Advanced Mode in the bottom right corner.

2.Then, under the "Advanced" tab, find the quotvmd settings menu quot.

3.Select quotEnable VMD Controller and change it to Enabled quot below.

4.Once the installation is complete, press the keyboard quotf10 quot; Then select the OK to save and restart your computer.

4.Finally, when installing Win11, insert the USB flash drive and select the load drive.

Heart of Kings 2 click to play

If you have any questions, please do not hesitate to ask, we will do our best to assist you!

One word missing, it's the hard drive.

Enter the BIOS and change the hard disk mode to AHCI mode.

The hard disk cannot be found in the computer system, and the hard disk replacement is repaired.

Has the system been installed, if it is finished, after taking out the disc, don't forget to change the first boot to a hard disk in the CMOS settings.

When the system is reinstalled, the system prompts that the disk cannot be found, which proves that the system does not recognize the disk

1) Check the condition of the hard disk cable after shutting down, whether the SATA cable and the hard disk power cable are connected firmly, and plug and unplug them again, 2) Reboot the BIOS to confirm whether the hard disk can be detected, 3) If the BIOS cannot detect the hard disk, it means that the hard disk has been damaged and needs to be replaced.

4) If the BIOS can detect the hard disk, mount the hard disk to another computer, enter the system's disk manager, initialize it, repartition it, and use it after formatting.

If the partition of the entire hard disk is deleted, you will not find the hard disk, and the partition that is not formatted after the partition can not be found. Unless your hard drive is replaced.

In addition, the older SATA interface hard disk must first install the hard disk driver during the installation process, or the hard disk cannot be found.

It is recommended to install your hard drive on another computer and try it. It is best to configure a relatively new computer to see if it can be recognized, or to check the hard disk if the hard disk is good. It is recommended to ask for advice on how to install the system on SATA port hard disks.

You should check if your hard drive is not connected.

Check the terminal blocks of the hard drive, and then you have merged the hard drive, and you have to repartition it.

Is there a key or something like that?

1: Try to install a new system under DOS, that is, start the installer with the installation CD, format the partition where the original system is located and then install it directly under Windows, there will be compatibility problems

2: Check whether the cable between your hard disk and the motherboard is broken or loose, the old IDE interface hard disk cable is most likely to have this failure and see if the hard disk jumper is set wrong, especially under the dual hard disk, pay attention to this problem

3: If there is only one hard disk, you can use PM software to check whether the partition table of the hard disk is wrong, if there is a repair, you can install the program to confirm the other hard disk

1. Turn on the computer, press F10 continuously to enter the BOIS page, you will see the following screen, in this page, change the AHCI mode to IDE mode.

2. Enter the diskgenius software, you will see the following screen, click on the quick partition above.

3. Go back to the DiskGenius window, click on the hard disk menu above, and select the corresponding option as shown in the figure below.

4. After clicking, you will see the following screen, click to select hard disk.

5. After clicking, you will see the following screen, click the Start Detection, Try Repair button to repair the hard disk.

6. That's it.

not detected means that the hard disk was not found.

You go to the boot option to see if there is a hard disk inside the first boot.

Please describe the problem in detail, and it is recommended to upload ** description.

1) The first reason: that is, the hard disk mode is different, resulting in the use of U disk reinstallation does not recognize the hard disk, because most of the hard disks of the computer are serial port hard disks, and the ordinary XP installation disk and the Ghost version of the installation CD, they do not integrate SATA control driver (or some are also integrated, but do not match the actual SATA control driver), resulting in incompatibility, and can not identify the hard disk, resulting in the inability to install the operating system or blue screen normally, so it is necessary to change the mode of the hard disk, change the AHCI to IDE mode, and the hard disk can be recognized and the system can be installed normally.

Hope it helps.

Ask how to switch.

It is necessary to partition the disk when reinstalling the system.

Hello, set the Legacy boot priority in the BIOS and see if it works.

If it doesn't work, enter PE in UEFI boot mode, use DiskGenius to partition NVMe solid-state select GUID mode, and then reinstall the system to see if it can work.

It may be that you forgot to partition when you did the system, you can re-divide the area before doing the system, remember to set the main partition, or there will be you this consequence, you are the partition chaos, you can click on my computer, right-click in the disk management to see if there are other disks, do not move the C disk, reset the other disks to divide the storage, if not, you can only re-partition the system, hope to adopt.

The hard drive cable is not in good contact or the hard drive is damaged, or the new hard drive is not partitioned.

Maybe your PE doesn't support SATA

You can go to the BIOS and change it to IDE compatibility mode first.

Server or desktop? How many hard drives? What system do you want to install, cloud repair network system troubleshooting.