How to install the switch socket in the bedside lattice? 5

Normally, the situation that is often seen in life is basically the socket on the top or side of the bedside table, because in this way, the charging equipment can be placed on the bedside table when in use. However, it was found that some netizens on the Internet think that the socket should be set on the back of the bedside table, and they think that the socket appears on the top of the bedside table, which not only affects the appearance, but is also particularly easy to be touched when in use, so they think it is best to put it underneath.

I dare not agree with such a statement. Because after all, the socket is to protrude from the wall to a certain thickness, if placed under the bedside table, not only waste a certain amount of space, but also move the bedside table every time you use it, which is not only impractical but also a waste of limited space area. Therefore, it is advisable to set it above the bedside table and at a certain distance from the bed.

The installation of the socket next to the bedside table needs to take into account the height of the bedside table and the usage habits of the occupants. In real life, the bedside table is generally shorter than the height of the bed, and the height is mostly more than 70cm, so the height of the socket should be at least 75cm.

In addition, the installation of the bedside table socket should also pay attention to these two points, first of all, first determine the location and size of the bedroom bed, and then determine the socket location, otherwise it will be embarrassing if the socket position is just blocked by the headboard. Secondly, the height of the socket, according to the ergonomics and the experience of actual life, the height of the socket is slightly higher than the height of the bedside table, which is the most convenient and reasonable to use. Finally, the number of sockets, if there are not a lot of electrical equipment in the bedroom, it is recommended to install one on each side of the bedside table.

Take a picture of the actual situation to have the right guidance.

The household bedside socket is surface-mounted or concealed, and the concealed installation should be pre-embedded 86-type junction box.

Surface-mounted is installed with an ordinary top-wire box.

The wiring is very simple, connect the live wire to the socket L hole, and connect the neutral wire to the socket N hole. One hole is left with a grounding wire.

Is it a three-control switch? Or a normal socket?

The switch is installed with reference to **. Two dual-control switches and one intermediate switch are required.

Installation Method:

1. Use the ink cartridge to play the line before opening the line groove on the wall and the ground to facilitate positioning. The pipe surface and the wall surface should be left with a powder layer of about 15mm;

2. When the power line pipe is buried, it should be considered to keep a distance of more than 500mm from the weak current pipeline, and the parallel distance between the wire pipe and the hot water pipe and the gas pipe should not be less than 300mm.

3. Reduce the turning of the wall line pipe as much as possible, and avoid the installation position of wall mirrors, furniture and other objects to prevent damage by electric hammer and nails.

4. Power sockets and a socket should be set on both sides of the head of the bed, and more than three power sockets should be set up near the computer desk and on the background wall of the TV cabinet in the living room, and the corresponding TV, **, multi**, broadband network and other sockets should be set up.

5. All in-wall wires are buried with PVC flame retardant pipes of more than 16, and the wires occupy <40% of the pipe diameter, and special interface devices are used for connection with the bottom of the box.

9. When using the conduit, the power conduit should be made a reasonable turning radius when passing out from the ground, special attention must be paid to the use of casing and glue connection under the ground, before the ground is not closed, the PVC pipe sleeve must be protected, and no rupture damage is allowed; When laying floor tiles, the PVC casing should be completely covered with cement mortar.

(1) Master bedroom Switches: 1 (master bedroom ceiling light) Sockets: 6 (two bedside lights, air conditioning, **, TV, floor lamp) (2) Secondary bedroom (children's room) Switches:

1 (second bedroom ceiling light) Sockets: 4 (air conditioner, **, desk lamp socket, spare socket) (3) Study switch: 1 (study ceiling light) socket:

6 (network port, air conditioner, **, study desk lamp, computer, spare socket) (4) Living room switch: 1 (living room top light) Socket: 6 (TV, water dispenser, air conditioner, **, floor lamp, spare socket) (5) Bathroom switch:

2 (bathroom ceiling light, exhaust fan or bath bomb) Sockets: 4 (washing machine, hair dryer, electric water heater,**) (6) Kitchen (kitchen, dining room in one) Switches: 2 (kitchen ceiling light, dining room ceiling light) Sockets:

7 (refrigerator, range hood, kitchen treasure, microwave oven, shabu-shabu socket on the dining table, at least two spare sockets on the countertop) (7) Balcony: Switch: 1 (balcony top light) Socket:

1 (spare socket) Friends can make appropriate adjustments according to their own needs.

Hello, I can solve it for you! You need to have 2 dual-control switches and 1 multi-control switch! The wiring diagram is as follows:

1. Clean the bottom box of the switch and socket.

The switch socket is installed after the carpenter, painter, etc., and the bottom box that has been left for a long time will inevitably accumulate a lot of dust. Clean the switch socket bottom box during installation, especially clean the dust and impurities in the box, and wipe the residual dust in the box with a damp cloth. Doing so prevents special impurities from affecting the use of the circuit.

2. Power cord treatment.

Leave the wire thrown out of the box for repair, and then cut out the core, taking care not to touch the core. Coil the wire clockwise on the binding post corresponding to the switch or socket, and then tighten the indenter, requiring that the core is not exposed.

3. Three-wire wiring method of socket.

The live wire is connected to one of the two holes of the switch, and then the insulated wire is connected from the other hole to the L hole of the three holes of the socket below. The neutral wire is directly connected to the N hole in the 3 holes of the socket. The ground wire is directly connected to the E hole in the 3 holes of the socket.

If the neutral wire is misconnected with the ground wire, the electrical appliance will trip when it is used.

Fourth, the switch and socket are fixed and installed.

First, the wire thrown out of the box is threaded through the outlet hole of the plastic table, and then the plastic table is tightly attached to the wall and fixed to the box with screws. After fixing, the wires are threaded out of the wire holes of the switch socket according to their respective positions, and the wires are pressed firmly according to the wiring requirements.

Finally, attach the switch or socket to the plastic table, align it and fix it firmly with screws, and cover it with a decorative plate.

Two socket installation methods.

When wiring switches and sockets, only one wire can be connected to each pile head, and the wire splicing head cannot be spliced on the terminal pile head. Because if two wires are spliced on the pile head (the switch and socket pile head are generally very small, and the original design is only connected to one wire), the loosening will affect the normal use of the latter switch or socket, and the wiring pile head is easy to heat, and the light one burns out the switch and socket, and the heavy one causes a fire.

The installation position of the switch is generally from the ground, 15-20cm from the edge of the door frame. The switch behind the door should not be installed due to the inconvenience of opening. The switch within a unit should be opened and closed in the same direction.

The socket is generally 30cm above the ground. The height of the toilet and kitchen sockets is determined separately. Splash-proof sockets should be installed in the bathroom, sockets should not be installed on the three sides above the bathtub, and sockets should not be installed above the faucet.

Sockets cannot be installed within 15 cm of the gas meter circumference. (The gas appliance and electrical equipment are set in a dislocation setting, and the horizontal clear distance shall not be less than 50cm).

When installing a single-phase three-prong socket, facing the socket, the upper eye should be connected to the ground wire, the left eye of the lower two eyes should be connected to the zero wire, and the right eye should be connected to the phase wire. When installing the two-eye socket, the left eye is connected to the zero wire, and the right eye is connected to the phase wire, and it cannot be connected wrongly. Otherwise, if there is electricity in the shell of the electrical appliance, or if there is electricity in the shell when the appliance is started, an electric shock accident will occur.

Household appliances generally avoid using two-eye power sockets. Desk fans, floor fans, washing machines, refrigerators, etc. all use single-phase three-prong sockets. Ordinary switches shall not be used for the installation of bath bombs and electric heaters, and switches that match the current of the equipment shall be used.

Due to the large current of household air conditioners, it will affect other electrical appliances in use when starting, so the air conditioning socket should be set up separately from the user's distribution box. The installation height of the socket should avoid the position where the air conditioner introduces the refrigeration pipe (that is, the position of the reserved hole on the wall), and the socket should be installed about 10cm above the position of the reserved hole.

Answer: Bull switch socket installation, prepare the switch socket (that is, the socket with switch), the red wire live wire is connected to L, the yellow wire is connected to the ground wire L1, and the blue wire is connected to the neutral wire L2; The specific steps are as follows:

1. Prepare the switch socket (that is, the socket with the switch). 2. The red wire is connected to L, the yellow wire is connected to L1, and the blue wire is connected to L2.

3. The live wire jumper on the switch jumps to the L on the socket.

4. The L2 on the socket is connected to the control line of the lamp.

5. The zero line of the lamp line comes out to connect to the electric switch.

You take a look at the pro.

3. Installation of switches and sockets: Concealed installation: According to the wiring requirements, connect the wires thrown out of the box with the panel of the switches and sockets, push the switches or sockets into the box to align the box eyes, and fix them firmly with machine screws.

When fixing, make the panel upright and flush with the wall. If there is a decorative cap on the panel mounting hole, it should be installed together.

Surface-mounted: first throw out the wire from the box through the outlet hole of the plastic table, and then the plastic table is tightly attached to the wall and fixed on the box or wooden brick with screws. After the plastic table is fixed, the phase wire and ground (zero) wire thrown out are threaded out of the wire hole of the switch and socket according to their respective positions, and the wire is pressed firmly according to the wiring requirements.

Then attach the switch or socket to the plastic table, align it, and fix it firmly with wooden screws. Finally, put the cover plate of the switch and socket on the plate.