Where are the four points of reversing into storage, and how can the first point of reversing into s

There are four points for reversing and warehousing, and there is no problem if you learn to reverse and enter the warehouse!

When the lower edge of the left rearview mirror coincides with the starting point induction line (usually the yellow dotted line), it is killed to the right. However, it is important to remember that the yellow line itself also has a width, and the timing of this overlap should be grasped well, following the principle of sooner rather than later.

Reversing into the garage if in the right to kill, the direction of the early hit, through the right rearview mirror to observe the body and the corner of less than 30cm of the margin, at this time, the direction can go back half a circle, stabilize the speed, if the body and the corner distance is still less than 30cm and then slightly back to the direction, has been maintaining a 30cm margin can.

How-to tips

1. Control the driving speed and idle with 1 gear or reverse gear throughout the whole process, and drive at what speed you start.

2. Carefully observe the process of reversing after controlling the steering timing, grasp the key points of steering, and turn in a timely manner.

3. When controlling the driving route test, the driving route of the car mainly depends on the speed and speed of rotating the steering wheel.

1. Adjust the position of the car first, keep the body in the test zone, stop when the shoulder is about the same level as the control line on the ground, and then reverse gear.

2. Look at the left rearview mirror when reversing, when the lower edge can almost overlap the control line, immediately kill the direction to the right.

3. Look at the margin between the body and the corner of the library at any time, you need to keep it at 30 cm all the time, if not 30 cm, pay attention to adjustment.

4. When the body is put into storage, and when it is parallel to the sideline, adjust the direction back to the right, and look at the rearview mirror at any time, which side the distance is wide.

5. Look at the body when the car is out of the warehouseIf it is not correct, it should be transferred, and the rearview mirror should be checked at any time so as not to accidentally press the line.

6. When the left is reversed, the observation point is similar to that of the right reversed. Also, when the lower part of the car's left mirror almost overlaps the control line on the ground, you have to stop the car.

Operational essentials. 1) Pour into the garage from the starting point.

After the driver gets into the car, first adjust the seat and rearview mirror, and fasten the seat belt, then put the car in reverse gear, release the parking brake lever, the car starts and reverses at idle speed, and the driver observes the garage through the right rear window.

When you see that the black edge of the right rear window is aligned with the right line of the garage, turn the steering wheel to the right at a constant speed to the limit.

After the car is in the garage, the driver looks back at the left side mirror, and when he sees the entire left side line of the garage appearing, he immediately returns to the steering wheel.

Stop immediately when you see the left door handle level with the garage bottom line from the left side mirror.

2) Drive from the garage to the return point.

When the car is driven out of the garage in 1st gear, when you see the hood approaching the road edge (Figure 4-6), turn the steering wheel to the left and stop straight behind.

3) Reverse into the garage from the return point.

The car is in reverse gear, keeping the steering wheel left turn limit position unchanged and reversing backwards.

The driver observes the left side mirror and corrects the direction so that the rear of the car is reversed into the garage.

After the car is put into the garage, the driver pays attention to the right side mirror, and when he sees the whole garage right side line appears, he immediately returns to the steering wheel.

The driver then turns his gaze to the left side mirror and stops as soon as he sees the left door handle at the level of the garage bottom line.

4) Drive from the garage to the starting point.

When the car drives out of the garage in 1st gear, when you see the hood approaching the roadside, turn the steering wheel to the right and stop straight behind.

The above content reference: Encyclopedia - reversing storage.

The lower edge of the left rearview mirror is pressed parallel to the left rearview mirror when the steering wheel is killed on the right, if this point hits the early back can be repaired, if the fight is completed directly into a hand.

1. First of all. The car should learn to align with the line, and when the car is coming, the left front of the car should be in front of the middle of the second and third dotted lines, and drive smoothly until the parallel is right. The wheel should be pressed over the yellow induction line. Stop the car.

2. Hang the reverse gear, start reversing, when the lower edge of the left reflector touches the direction of the induction line, it will be killed to the right and reverse.

3. From the right side of the mirror, observe the distance between the body and the corner of the library, learn to repair the direction, more than 30 cm continue to die, less than 30 cm, to the left back direction, as for how much to go back to see how much to put the wheel into the warehouse.

4. When the body is parallel to the sideline, the direction is back to the right and continues to reverse.

5. Finally, stop, look at the induction line from the lower edge of the left reflector, and overlap the parking. The end of the right inverted library.

Reversing warehousing skills are detailed**:

1. Judge whether the left and right distance of the target parking space is sufficient, and after confirmation, slightly close to the parking space and control the distance between the sides of the car on the left and right.

2. The position you sit in is exactly in the middle of the next parking space.

3. Then reverse backwards, change the steering angle appropriately when reversing, and control the distance from the vehicle in position.

4. After crossing the boundary line of the parking space behind the left rear of the rear of the car, slow down the reversing speed and look at the right rearview mirror.

5. When there is a gap with the vehicle on the right, adjust the steering angle appropriately, adjust the distance between the left and right vehicles, and try to make the distance between the left side slightly larger than the right side, so as to provide convenience for the opening door.

Right storage: the first point, the lower edge of the left rearview mirror is pressed parallel to the left rearview mirror when the steering wheel is killed on the right, because the author is relatively short, so it is necessary to kill the right when it has not been pressed to the library line (if this point can be repaired after the early rearview, if the fight is completed directly into the front).

The second point, when the most convex part of the body and the right corner of the garage in the right rearview mirror are two finger widths, the steering wheel turns back to the left, and here it is emphasized that the next circle is not more or less (if the first point is late, there is no need to return here).

The third point, in the right rearview mirror, points to the middle of the front door handle of the car, and then to the right. (Later proficiency can not look at the door handle, according to the position of the rear wheels into the warehouse, this has an advantage, you can flexibly choose whether to continue to repair or the right to die, to ensure that the rear wheel into the garage and then look at the left rearview mirror).

Fourth, from the left rearview mirror, you can see that the steering wheel in the left rear corner immediately returns to the right.

The fifth point, that is, the parking point, is still to stop when looking at the lower edge of the left rearview mirror and the fast pressure parallel to the left rearview mirror. Here, the same as the first point, the shorter one has to stop when it has not yet pressed the reservoir line.

Right out of the library: when the left rear wheel out of the library line, to the right to kill, look at the window line and the library line parallel to the normal, at this time to see the front should be large and small, this is because the body itself is arc, it looks oblique in fact stopped right.

The left library can be the same as the right library step in the opposite direction, the following is an introduction to the left library that my coach taught at the time, the advantage of this left library is simple, the disadvantage is that there is a dead spot when the library is reversed. (What is a dead spot?) It is to be repaired early, and it may be pressed late)

The first point. When the source, such as the lower edge of the left rearview mirror, coincides with the starting point induction line (usually the yellow dotted line), it is killed to the right. But it should be remembered that the yellow line itself also has a width, and the timing of this overlap must be grasped well, following the principle of hail Lu Qining sooner rather than later.

The second point. If the interval is less than 30cm, you can adjust the direction of a circle or half a circle, and wait until the corner line of the library reaches the lower edge of the rearview mirror, and then hit the direction to the right; If the interval is greater than 30cm, the steering wheel does not need to move, and it is OK to reverse to 30cm.

The third point. When the lower line of the left rearview mirror coincides with the left exit line, you can stop. These points can be prepared in advance, because you can also make adjustments in advance, and it will be more difficult to adjust after the point.

The fifth point. After completing the reversing into the warehouse, start to go out of the warehouse, keep the direction back to the right, go straight forward, when the vehicle engine cover covers the front roadside line quickly to the left to kill the direction, because of the personal experience of Sun Gao difference, this point may be different, you can try a few more times, to find the most suitable position for yourself.

The sixth point. After leaving the warehouse, observe the left rearview mirror, when the left side of the induction line appears on the lower edge of the left rearview mirror, stop the station, the direction to keep the left to kill the state do not move, and then start the left rearview.

There are four main points when reversing into storage:

The first is that the stiffeners of the car (Poussin) are aligned with the ground wire (coach marking);

The second is to look at the ground point on the left side of the body when reversing into the garage, which is about 1 4 in the test area (this point will be marked by the coach);

The third is that after warehousing, the body (shoulder) is aligned with the point on the ground on the left side, that is, the warehousing state;

The fourth is to turn left out of the warehouse. Look at the front of the car to align with the chamfer of the ground and steps in front of you, and turn left.

The above four points are combined with the actual situation!

Driving into the reservoir area action decomposition:

Hear the voice broadcast reversing into the warehouse, hang in 1st gear, and go up to the right for 1 lap of the direction; Look at the left rearview mirror into the line, and hit 2 circles to the left; The car is turning back to the right for 1 turn; The wheels cross the stop line to stop.

Breakdown of the right inverted library action:

Hang into reverse gear, position 1 is facing the stop line, and immediately circle to the right; The distance between the right rear wheel and the storage position triangle is equal to 30cm, and it is 1 circle to the left, and more than 30cm is full to the right; The body is parallel to the library edge line back to the positive direction; The left mirror is parked vertically along the horizontal line facing the reservoir area.

Left outbound action decomposition:

Hook into 1st gear, front hood to the edge of the road, circle to the left; The body is positive, the steering wheel is circled, and the front wheels cross the stop line to stop (as shown in the figure above No. 2).

Left inverted library action decomposition:

Hang into the reverse gear, point 1 to the stop line, immediately to the left circle; The left rear wheel and the triangular distance of the storage position is equal to 30cm, 1 circle to the right, more than 30cm to the left full; The body is parallel to the library edge line back to the positive direction; The person on the left side of the mirror is parked along the horizontal line facing the reservoir area.

The so-called point is the point where you use a certain point as your visual reference in the process of reversing into the warehouse and perform a specific action.

In fact, whether it is a right or left dump, the most important points are two: that is, the point where you kill the steering wheel to the right (left) when the vault is reversed; When the warehousing is about to be completed, it is used as a reference point for the correction direction.

1. The first point: the point that kills the steering wheel.

When the left rearview mirror coincides with the starting line (which is usually told by the instructor), the steering wheel is immediately killed.

2. The second point: the reference point for correcting the direction.

1) When the body is about to be poured into the garage and the rear compartment of the car is close to the garage line, observe the horizontal distance of about 30 cm between the wheels and the parking space from the rearview mirror, and correct it if it is too wide or too narrow.

2) When the vehicle is in storage, look at the left rearview mirror and the edge of the library, when the lower edge of the left rearview mirror coincides with the edge of the library, when the edge of the left rearview mirror is just stuck and can not see the edge of the library, step on the clutch and brakes, stop, reverse into the warehouse is completed.

The main skill of reversing into the warehouse is to find a point, there are signs to do next to the library, generally with the left shoulder of the body to the point on the direction, and one of the most important is to repair the direction, the general direction back early or back late to repair the direction of the mold base here is particularly important.

The direction is a little later when the direction is late, if you are late, you have to go back to the direction early, the direction of repair is easy to make yourself dizzy at the beginning, I don't know where to play, slowly become proficient, but there is a premise that you must be slow, semi-linkage must be controlled, not fast and slow, to put it bluntly, the second section is to test your semi-linkage, and your own understanding is also very important.

The so-called point is the point where a certain point is used as your visual reference to perform a specific action in the process of reversing into the warehouse. In fact, whether it is right or left, there are two most important points: the point of killing the steering wheel to the right (left) when reversing; When the put-away is nearing completion, it is used as a reference point for the correction direction.

1.Point 1: Kill the point of the steering wheel.

When the left rearview mirror coincides with the starting line (usually the coach will tell you), the steering wheel is immediately killed.

1) When the body is about to be poured into the garage and the trunk of the car is close to the garage line, observe the horizontal distance between the wheels and both sides of the parking space from the rearview mirror by 30cm, and correct it if it is too wide or too narrow.

2) After the vehicle is in storage, look at the left rearview mirror and the edge of the garage door. When the lower edge of the left rearview mirror overlaps the edge of the garage door, and when the edge of the garage door is just not visible on the lower edge of the left rearview mirror, press the clutch and brakes, stop the car, and reverse into the garage.

The main trick of reversing into the warehouse is to find a point. There is a sign next to the warehouse. Generally, the left shoulder of the body is aimed at the direction of the point. The other most important thing is to determine the direction. Fixed orientation is especially important when the general direction returns early or late.

When you hit the direction early, put it in the warehouse, and return to the direction later. If you're late, you'll have to get back to that direction early. It's easy to get dizzy when you first set the direction.

I don't know how to hit **, I need to master it slowly. However, there is a premise that you must slow down and control the semi-linkage. To put it bluntly, the second year is a semi-linkage test for you, and your comprehension skills are particularly important.

Millions of car purchase subsidies.