What should I do if I can t print after adding ink to the Canon inkjet printer IP1880

Play a few more cards after the bet and try again later. Every time you add ink, add less, add a few more times don't be afraid of trouble, it's really not good to change the cartridge again, use up and then fill the ink, drill a small hole on the line, be sure not to add too much ink!

If you let it go for a while.

You can just change the cartridge.

Even, there are two, I didn't know one before.

Leave it at home for a while, and then it's like you're in this situation.

It works well with a different cartridge.

Grid of Canon ink, generally speaking, one can be added twice, and the landlord does not have to fill it up each time. After adding ink, clean the printer's printhead in your computer.

1880 belongs to the old model, but the ink cartridge belongs to the new one, that is, the kind with the nozzle on the cartridge, it is generally not easy to clog the nozzle, the maintenance cost is relatively low, the cartridge has a chip on it, do not touch the chip and the nozzle when adding ink.

After adding the ink, it is necessary to use a software to clear the zero, the ink can not be added more at a time, more will leak, and the number of times you add will only have an impact on the ink cartridge, and the printer will only cause more waste ink.

When there is a white line printed or the handwriting is illegible, it is time to replace the printhead.

Each model only has a corresponding cartridge, and there are other different brands of alternative cartridges, ** cheap can be used, but the color effect is not as good as the original.

There are many brands of ink, and they generally follow the price of one penny.

The reason why the Canon printer IP1180 does not enter the ink supply pipe is that the printhead is clogged and the printhead needs to be cleaned again.

Tools Materials: 1 bottle of clearing liquid, 1 cup of purified water, and a few cotton swabs.

Here's how: <>

Summary. Hello, 1, the printer pop-up interface shows that the following cartridges cannot be recognized, then you need to turn off the printer first. 2. When both indicators are off, unplug the power cord of the printer.

3. Then you need to replug the power cord of the printer and press and hold the power button. 4. When the power button is green, press the button below the power button three times in a row. 5. Then press the two keys and let go at the same time, and the printer is in a shutdown state.

6. After a short while, turn on the printer again, the printer boot button will be evergreen, and then the printer can be used normally. 7. After that, you can use the printer to print on the computer.

Hello, 1, the printer pop-up interface shows that the following cartridges cannot be recognized, then you need to turn off the printer first. 2. When both indicators are off, unplug the power cord of the printer. 3. Then you need to replug the power cord of the printer and press and hold the power button.

4. When the power button is green, press the button below the power button three times in a row. 5. Then press the two keys and let go at the same time, and the printer is in a shutdown state. 6. After a short while, turn on the printer again, the printer boot button will be evergreen, and then the printer can be used normally.

7. After that, you can use the printer to print on the computer. Thank you!

This issue occurs because the ink model and printer model are inconsistent, and this issue can be resolved by replacing the ink cartridge. The specific steps are as follows:

1. First of all, after confirming that the printer has no powder, you need to take out the toner cartridge of the printer, as shown in the figure below, and then enter the next step.

2. Secondly, after taking out the toner cartridge, remove the toner cartridge from the photoreceptor drum.

and hold the green button on the left side to perform the detached operation as shown in the image below, and then proceed to the next step.

3. Then, take the newly purchased powder cartridge out of the package, shake it horizontally several times, mainly to shake the inside of the powder as shown in the figure below, and then enter the next step.

4. Then, remove the yellow plastic cover on the front of the new toner cartridge, and then move on to the next step.

5. Then, put the new toner cartridge into the original toner cartridge and press down gently until the green source on the left side of the card.

is locked, as shown in the image below, and proceeds to the next step.

6. Next, install the installed toner cartridge into the printer as a whole. The installation method is the opposite of the removal method, as shown in the figure below, and then proceed to the next step.

7. Finally, after installation, close the front cover, and then turn on the printer to perform the system test. After the test is successfully completed, the green light is lit and the Canon printer can be used normally, as shown in the image below. In this way, the problem is solved.

Canon IP2780 printer shows that the ink cartridge cannot be recognized after changing the ink, what should I doHello dear, Canon IP2780 prompts that the ink cartridge cannot be recognized, you can refer to the following solutions: This problem, generally reinserted a few times can be solved, plug it in for a while and then turn on the test. If it doesn't work, try the following methods!

To adjust the wiring, see if the left and right length is just right, too long or too short, will affect, turn on, let the ink car automatically move out to the middle, unplug the power, and then move the ink car left and right, so as to adjust the appropriate position of the pipeline, this depends on your own hands. In addition, the clip of the card line should not be pasted too low. I can't recognize the cartridge, it should be the red hole of the color, it is drilled too high, and the red outlet should be sealed, and the hole below will not be prompted.

If that doesn't work, try the following; 1.Reinstall the drive. 2.

Remove the cartridge and wipe the chip with an eraser. 3.Is the data cable normal?

1. If the ink cartridge is fine, turn off the printer, and then connect it again, sometimes because of some problems with the system.

2. Or you should pay attention to the position of your printer, if there is a problem with the placement of the printer, it will also cause it to not work.

3. If it doesn't work, turn off the printer, then take out the ink cartridge, and then align it to install it. Not yet, check the driver, reinstall the driver.

4. If none of the above can be solved, it may be that the metal sheet on the cartridge has not been used for a long time, and the contact is poor, so you have to take out the cartridge, and then wipe it clean with an eraser, and you will find that the metal sheet on the cartridge is shiny. If you install it again, there will generally be no problem.

5. If the problem cannot be solved, it is necessary to consider whether the cartridge is damaged, and it is recommended to replace the cartridge.

6. It is recommended to contact professional maintenance personnel for maintenance.

The printer cannot print, and the display status is wrong because the printer is set incorrectly, and the printer can be set again.

1. Right-click [My Computer] and click [Manage].

2. [Services and applications, click [Services].

3. Find the [printspooler] item on the right, right-click and select [Stop].

4. Sun Zhengyin win r open and run, enter [spool] to confirm.

5. Go back to [Service] and start [PrintsPooler].