What should I do if my Zenith repair watch is magnetized?

1. If you are sure that it has been magnetized, it is recommended to take it directly to a professional watch repair center (shop) for demagnetization. Because self-demagnetization is usually not very clean, or has a certain impact on the watch, and demagnetization is usually free, so why not do it to ensure safety? Reminder:

The watch must be kept away from magnetic fields, such as televisions, mobile phone earpieces, ** earpieces, razors, refrigerator doors, magnetic necklaces and other things with magnetic fields, in fact, as long as the distance between these things is more than 5-10cm, the watch is safe.

2. There are many anti-magnetic watches, but the so-called anti-magnetic watches are not all parts of the watch are anti-magnetic, but only the main parts, such as balances, hairsprings, springs and other parts made of anti-magnetic materials. Although it is an anti-magnetic watch, it can only serve a preventive role, so you should avoid placing the watch next to electrical appliances or magnetic objects that generate magnetic fields.

3. Both magnets and DC magnetic fields can magnetize "hard magnetic" materials such as steel. There are many steel materials in mechanical watches, such as large and small steel wheels, escape wheels, shaft tenons of gears, bearings, screws and hairsprings, and when the hairspring is magnetized, the watch will stop immediately. Magnetized watches may not see any problems in the short term, but as time goes by, it will become slower and slower.

4. The watch should avoid being close to the magnetic field, such as placing it next to the electrical appliances (such as stereos, refrigerators, computers, etc.) or magnetic objects (such as magnets, mobile phones) that generate magnetic fields.

1.The demagnetization of a watch theoretically places the watch in a strong alternating magnetic field, and the intensity also decays gradually. Usually, a large hollow coil is used, an alternating current is applied, the watch is placed in the hollow coil, and then slowly withdrawn, which is equivalent to gradually reducing the strength of the magnetic field.

This action has to be repeated many times, and each time the watch must be changed by 90 degrees, because the demagnetization effect is best when the magnetic field lines of the demagnetized magnetic field and the magnetic field lines of the demagnetized watch are in the same direction, and when they are at an angle of 90 degrees, they are invalid. Therefore, it is necessary to demagnetize the watch in all directions before it can be cleaned.

2.The professional demagnetization equipment uses a C-type silicon steel core with two sets of coils to discharge with a large capacitor to produce an alternating magnetic field with attenuation. The watch is placed in the groove of the demagnetizer, press the button, the neon lamp flashes to complete the demagnetization instantly, of course, the watch also needs to change several directions and repeat the demagnetization process.

3.To demagnetize the watch in a simple way, it is to find a transformer (the power should be sufficient) or something, and it is also to gradually move the watch closer to their core, and then gradually leave; Change the angle or the direction of the watch and repeat this action constantly, but this method does not guarantee that the watch will be demagnetized. Demagnetization should also be a necessary procedure for watch maintenance, and the accuracy of the watch should be corrected after it is completely demagnetized.

Magnetic field is everywhere, it is impossible to prevent it, and the watch that has always been very accurate in the time has suddenly appeared in the situation of time error, and the first thing to guess is whether the watch is magnetic. There are many steel materials in mechanical watches, such as large and small steel wheels, escape wheels, shaft tenons of gears, bearings, screws and hairsprings, so watches are very susceptible to magnetization. Once the mechanical watch is magnetized, the first situation that affects it is that the watch is not accurate, there is an error, and in the serious case, the watch stops.

Moreover, in the development of today's social life, more and more electronic products appear around us. Therefore, the magnetic field is present around us, and there is only a difference in the strength of the magnetic field. Various types of permanent magnets are also widely used in electrical appliances, typically speakers and motors, and both magnets and DC magnetic fields can magnetize "hard magnetic" materials such as steel.

There is also the magnetic buckle on the leather bag, and the watch and credit card are the most afraid of being stained with magnetism. Mechanical watch magnetization is generally fast (serious will stop), if the hairspring is stuck together, the watch will go faster, about 2 hours or so faster. Steel parts are most susceptible to magnetization, including escape wheels and pallet forks.

The simple way to tell is to use a sensitive point compass and lay it flat. Then the watch is quickly and repeatedly skimmed over the top of the compass at close range, and this action also needs to change the watch in a few more directions, and then repeat. As long as the needle of the compass moves, it means that the watch has been magnetized.

The principle of the demagnetizer is that it can produce an alternating magnetic field, and if the watch is placed in this magnetic field, it will be demagnetized, and if it is a constant magnetic field, it will be magnetized. Demagnetizers can be bought or made by themselves, and generally professional watch stores have demagnetization services. Moreover, in your daily life, you must be careful not to place your watch near or near electrical appliances that generate magnetic fields (such as stereos, refrigerators, computers, etc.), or magnetic objects (such as magnets, mobile phones).

There is a special mechanical watch demagnetizer for mechanical watch magnetization, and there is no need to open the back cover of the watch, and the demagnetizer can be turned on the watch a few times to eliminate magnetization. You can go to an experienced and professional watch repairer** to deal with it.

The watch should avoid being close to the magnetic field, such as placing it next to electrical appliances (such as stereos, refrigerators, computers, etc.) that generate magnetic fields, magnetic objects (such as magnets, mobile phones), and women use handbags to open and close magnetic buckles, and men use mobile phone covers to turn on and off magnetic buckles, which may make the watch magnetic, causing the watch to run inaccurately or temporarily stop.

Magnetization of the watch: Many things with magnetic fields are often together with the watch, which leads to the phenomenon of magnetization of the watch, causing the watch to be inaccurate. After being magnetized, the watch may stop, slow, or fast.

After the watch is magnetized, its magnetism will not recede by itself, in which case it can only be demagnetized. Therefore, you can only go to a professional watch repair center for demagnetization so that it can return to normal.

Watches often appear next to these electrical appliances (mobile phones, televisions, computers), and when magnetized, they can affect the timing of the watch at least or stop it directly. Although you can degauss according to the method on the Internet, it is easy to have unclean degaussing, which affects the operation of the movement. The need for degaussing is actually very simple, it is recommended that you go to a professional maintenance network to use the demagnetization machine, which can be perfectly solved in a minute or two.

The watch is in excessive contact with objects with magnetic fields, which leads to the phenomenon of magnetism on the watch, causing the watch to run inaccurately. After being magnetized, the watch may stop, slow, or fast. If the symptoms are mild, the daily error is tens of seconds.

In severe cases, the daily error is several points. After the watch is magnetized, its magnetism will not recede on its own, and it needs to be demagnetized to restore it to normal.

If there is a problem with the watch, I recommend going directly to the watch after-sales center. After-sales is not only more professional technicians, but also the instruments are imported, more precise, and **also very transparent, will not be messy**. When not to go to a regular after-sales center.

Otherwise, if you are trapped, you can only blame yourself.

If there is no warranty, take it to the after-sales service to do degaussing, and then test the time. If it is out of warranty, it will be taken to a repair center with certain qualifications. Remember not to believe in home remedies, and be sure to go to a repair center for regular repairs.

If the watch is magnetized, you can take it to the customer service center or the watch repairer, and test it on the meter to know the problem.

1.With a finished watch demagnetizer, about a few tens of yuan a piece (the inside is a coil, with an iron core in the middle, connected to 50Hz alternating current, generating alternating magnetic field demagnetization), can also be self-made;

2.Put the watch on a non-magnetic iron plate for a few days, the magnetism will be conducted to the iron plate, of course, the larger the volume of the iron plate, the greater the magnetic capacity, and the better the effect;

3.Slowly pass the watch through a non-magnetic ring, which will be left on the ring;

4.The most common and safest way, if it is too troublesome or feel that you can't get the magnet clean, then you can go to the watch shop or warranty point to find a watch repairer to repair.

After the watch is magnetized, its magnetism will not recede on its own, and it needs to be demagnetized to return to normalAnti-magnetic watches are only the main parts, such as the balance wheel, hairspring, mainspring and other parts made of anti-magnetic materialsAlthough it is an anti-magnetic watch, it can only play a preventive role, and it is not completely unscrupulous against magnetic fields.

Therefore, you can only go to a professional watch repair center for demagnetization in order to restore Zenith time.

ZENITH repairs watches are located in Room 04-05, 11th Floor, South Block, Hong Kong Plaza, No. 283 Huaihai Middle Road, Huangpu District, Shanghai.

It is recommended that you send it to a professional large-scale clock point for inspection and maintenance.

Once the magnetism on the watch is all of a sudden, it goes very fast, even 1-2 hours a day.

When wearing mechanical watches, pay attention to keep away from magnetic fields, such as stereos, televisions, mobile phones and other electrical appliances.

Magnetization is a common phenomenon nowadays, and the solution is not difficult, just go to the watch for repair and demagnetization, or bring your own demagnetizer, it only takes 30 seconds to demagnetize the watch, and there is no impact on the performance of the watch.

Hello, the watch will cause the problem of inaccurate time after being magnetized, although the quartz watch will not be magnetized, but there will be a phenomenon of stopping in a strong magnetic field. Therefore, when using the watch in daily life, it must be kept away from the magnetic field, away from TV, radio, induction cooker, etc., which will be magnetized due to long-term contact.

Many friends may be very confused, how can you tell that the watch is magnetic? There are many reasons why the watch is inaccurate or does not go, and the magnetic field in our daily life is everywhere, in order to accurately judge whether the watch is magnetized, you can use a flexible compass, put the compass flat on the table, hold the watch and shake it back and forth above the compass, if the needle of the compass moves, it means that it is magnetized.

There are two ways to degauss:

Methods of degaussing.

First, it is a professional demagnetization of the watch shop.

Methods of degaussing.

2. If you are far away from the watch repair shop, you can also demagnetize yourself, the specific method is: find a piece of iron that is hollow in the middle and is not affected by magnetization, stand firmly on the table, and then the magnetism on the watch can be "sucked" by the iron block to restore the watch to normal. It is to use a magnetized iron can, the two ends are connected, and the magnetized love watch can be demagnetized by moving back and forth in the iron can for 5-6 minutes.

The post-processing of the watch is very simple, take it to the customer service center. You don't need to open the cover, you can directly use the degauss device to demagnetize, and the watch can return to normal in 2 seconds. If you want to degauss yourself, you can also try the following two methods.

1. Find an unmagnetized iron ring, put the watch in the ring, wear it slowly, and after a few minutes, the watch will be demagnetized and restored.

2. The effective part of the induction cooker plate is generally round, and the coil is below, if you do not put a large enough steel object, it will generally automatically protect from starting, we had better find a steel water cup (represented by a red circle) filled with water, or other steel containers, in short, do not cover the center of the induction cooker, and it is enough to make the induction cooker start. Then start the induction cooker, it is best to use the maximum power, the watch or tool to be demagnetized, from the far left side of the stove close to the surface of the induction cooker, through the center point of the induction cooker to the right far away, so repeat several times, pay attention to enter from one direction, can play a good degaussing effect.

The center of Zenith's watch repair is located in Room 1507, South Tower, Guangzhou World ** Center Building, No. 371-375 Huanshi East Road, Yuexiu District, Guangzhou, and the reason for this is to protect the dial from further damage, because the value of the dial is often greater than that of the watch glass, especially for those expensive watches. I've seen cases where the watch is still moving because the glass is broken, and the hands scratch the dial and date because the glass is still moving, and the glass and dial have to be replaced together, which increases the cost of repair. Of course, it is best not to have this situation, the glass replacement of a famous watch is about more than 1,000 yuan, and if it is a special-shaped, it will be more expensive.

Hello, glad to answer for you.

For Zenith mechanical watches, after a certain period of use, the lubricating oil in the watch movement will gradually dry up, the friction between the gear bearings will increase, and the wear will increase, and at the same time, there will be a little iron filings between the parts that will be rubbed down, combined with the tiny dust that enters the movement, and adhere to the dry viscous lubricating oil, which will further aggravate the wear and tear of the gears and bearings, and it is easy to cause damage to the Zenith watch movement if it is not cleaned and maintained for a long time.

Generally, mechanical watches are best taken to the watch store every two or three years to clean and maintain, and watches that are not worn very frequently can also be extended to five or six years of maintenance.