Regarding my E home router problem, how is my E home connected to a router

If the encryption is set to WPA or WPA2, the encryption will be changed every 1 hour by default. If you set the password to be a little more complicated (a combination of alphanumeric symbols), it is generally unlikely to be rubbed into the net.

1. If you don't need the wireless function in your home, turn it off.

2, If you want to use wireless, you will use wireless A, change the wireless SSID (that is, the infinite name) to Chinese. Then change the encryption to WPA2.

Haha, such an ordinary immortal can't crack it.

At present, it is impossible to rub the Chinese name.

You can replace this built-in wireless router with a ZTE ADSL cat (without routing), and then add a Linksys 54M dual-antenna wireless router (more than 400) on it, wired and wireless can be used.

Find your gateway address, use this address directly in the browser to enter the routing settings page, and you can see whether the wireless network is turned on. Generally, the default gateway is or, you can check the IP of your computer's network card, and you need a username and password when you go in, and the default is generally "admin".

First of all, my e-home is not a route, it is a cat. Secondly, you need to crack it, search up and down the cracking plan, and if you can't figure it out, you can find a master to help you, it's not easy to do it remotely.

This is because the gateway of your router and the optical modem are the same 192 168 1 1.

You'll need to reset your router.

Common setting methods:

1. Turn off the modem or disconnect the modem from the router.

2. Connect the computer to the router, open the browser, and enter the router gateway 192 168 1 1 to connect.

3. After logging in to the router, under normal circumstances, you can set it to the dynamic acquisition mode, and set the wireless name and password.

4. Open the LAN port setting in the advanced settings, modify the gateway of the router from 192 168 1 1 to 192 168 2 1, save it and restart the router.

5. Turn on the optical modem and connect to the router, so that you can surf the Internet normally.

6. It should be noted that the next time you need to log in to the router for settings, you need to enter the new gateway 192 168 2 1 in the browser to log in to the router correctly.

This is because the setting address of the modem is the same as the IP address of the router gateway, disconnect the network cable connected to the modem and the router, set up the router first, and then connect to the modem.

Don't connect the router to the broadband network first, and set up the router separately first.

The steps are as follows; Step 1; Open a computer browser and enter the management interface of the router in the address bar.

Step 2; Select PPPoE and enter the broadband account and password.

Step 3; Set a wireless name and password.

Step 4; Save is complete.

There is a wifi (or wlan switch) behind my e-home wireless cat, and the wireless is turned off by pressing and holding for 5 seconds.

This is the IP of the optical modem.,Unplug the optical modem and then set up the router.,Change the IP address inside.,Don't change it.。

Maybe your broadband isn't set up.

Method 1: Connect to the WAN port of the secondary router.

1.How to connect the network cable.

One end of the network cable is connected to the LAN port of the main router, and the other end is connected to the WAN port of the secondary router.

Note: LAN port and WAN port, how to see? There is a small print above or below the interface on the back of the router.

2.First of all, configure the secondary router, and do not plug in the line of the WAN port first.

Connect the computer to the LAN port of the secondary router, log in to the router, and change the IP address of the secondary router.

Generally, it is set under the network parameters --lan port setting. You must restart it after saving.

If the main router and the secondary router need to be changed.

Note: The primary router and secondary router need to be changed to IP addresses from different CIDR blocks.

After the change, you need to restart, and after the restart, you need to use the changed IP to log in to the secondary router.

3.Reboot and log in to the router again.

Open the WAN port settings.

You can select static IP or dynamic IP for WAN port connection settings.

After selecting the dynamic IP, you don't need to set anything else.

To select a static IP, you must enter an IP address (the IP obtained from the main router and set by yourself, but the IP cannot be within the DHCP allocation range of the main router and the IP occupied by other devices in the network.) )

Subnet masks are.

The gateway is the primary router address.

The DNS server recommends entering the DNS address obtained by the WAN status of the primary router.

4.Connect the network cable from the main router to the WAN port.

At this point, if you need other settings, you can continue to set them on the secondary router, such as turning on the wireless network and setting a wireless password.

Method 2: Connect to the LAN port of the secondary router.

1.How to connect the network cable.

One end of the network cable is connected to the LAN port of the main router, and the other end is connected to the LAN port of the secondary router.

This connection is equivalent to using a router as a switch.

Note: LAN port and WAN port, how to see? There is a small print above or below the interface on the back of the router.

2.You also need to configure the secondary router, and do not plug in the cable of the LAN port first.

The computer is connected to the LAN port of the secondary router, and when you log in to the router, it is best to change the IP address of the secondary router, so that you can log in later.

Note: The secondary router must be changed to the IP address of the CIDR block of the primary router, and the IP address cannot be occupied by the DHCP allocation range of the primary router or other devices in the network.

After the change, you need to restart, and after the restart, you need to use the changed IP to log in to the secondary router.

3.Shut down the DHCP server.

Click Disable and save.

4.Connect the network cable from the main router to the LAN port.

At this point, if you need other settings, you can continue to set them on the secondary router, such as turning on the wireless network and setting a wireless password.

The cat delivered by the e-home does not have a routing function. Internet access can be shared, and both machines need to dial up. Recurring billing. You need to open 2 ports to China Telecom.

Hello! The specific wifi setting method of the e-generation home wireless router is as follows:

1. Connect the power supply of the router, and then plug one end of a network cable into the network port of the computer, and the other end into the LAN port of the router.

2. Open the browser of the computer, enter the IP of the router in the address bar, click the enter key to enter the settings page of the router, the user name is admin, the password is blank, click to log in, and enter the settings home page of the router.

3. After logging in to the homepage, select Manual Settings. Then select Manual Internet Settings, and Home Dial-up users select the PPPoE connection type. In the username and user, enter the username and password given by the ISP provider (Netcom, Great Wall, Telecom, Tietong, Cable, etc.) correctly.

The connection mode selection is always filled in with the mtu value of 1492. The save is done.

4. The wireless router also has a wireless encryption to ensure the user's wireless security. Select the wireless settings on the main page of the router's settings, select an encryption method in the security mode, any one of WEP, WPA, or WPA2, and then enter 8 or more Chinese characters or numbers as the wireless password in the security key, and the router settings will be completed after saving the settings.

5. After the setting is completed, the router will automatically restart, and the external network cable can be used by connecting the external network cable to the WAN port of the router.