Mercedes Benz new E231 maintenance light reset

Mercedes-Benz E200 maintenance light zeroing can be achieved by only operating the multi-function steering wheel, and the specific operation steps are as follows:

1. Press and hold the select key on the left side of the steering wheel, then quickly press the lower block key.

2. Enter the instrument setting interface at this time.

3. Select the English option below.

4. Choose a complete set of maintenance.

5. Select and confirm the whole set of maintenance.

6. Select the oil grade.

Notes:1. It can only be operated after maintenance.

2. If you don't do maintenance, the engine will be damaged.

1. First of all, start the Mercedes-Benz E280 vehicle, and call up the total mileage page of the vehicle through the adjustment button on the Mercedes-Benz E280 steering wheel.

2. Next, press and hold the button on the far right side of the Mercedes-Benz E280 steering wheel as shown in the figure below, and hold it for three seconds after the Mercedes-Benz E280 instrument will appear in the selection menu.

3. Next, select the ASSYST Plus option on the Mercedes-Benz E280 dashboard through the select button of the Mercedes-Benz E280 directional infiltration travel disk.

4. At this time, press the confirmation button on the Mercedes-Benz E280 steering wheel.

5. Finally, restart the Mercedes-Benz E280 to make the Mercedes-Benz E280 maintenance light zero.

I don't know which model your car is... I say two ways ... If you can understand, you will be 0 for the common Mercedes Benz car....

I'm just saying it with an e-boy... I'll start with the ...... with chassis number 211...... when the first square is openedThen press the up and down buttons to make the dashboard in the default interface, which is the interface that displays temperature and mileage, note that this is a very important ......If there is a prompt on your car about how many kilometers have passed for maintenance, you must press the enter key to make the interface in the default interface, and then quickly press the mileage zero button three times (some cars have the r button, you can choose to press the r button.) Then the voltage information will be ......Just press the system key, like that one, press the "+" and "-" keys and select "confirmation" (if not, select the third option) ......Press the system key again to confirm the ......Go in and choose complete service" (choose the first option without that word......).As long as you remember to choose 3 at the beginning (some cars choose 4, but you just need to remember to choose maintenance confirmation), the second time you choose 1 is right.

Then the system key determines the ......Wait for about 30 seconds to turn off and then turn on When you can explain here how many kilometers ...... your car has been maintained if it has been maintainedThe instrument display may not be 10,000 kilometers, which can only be changed by computer. The method of 212 is the same as the meeting steps ...... 211Press and hold the OK key and the ** key at the same time as the ** key to the right...At this time, the meter shows "assyst plus"; Just select this and press OK to confirm.

Then select "service performed" (or "service done") for some cars that are in Chinese, (in the same way) and press "OK OK." Sometimes the dashboard says that the maintenance cannot be completed, you don't care about it, just press confirm. The back is the same as the front, so I won't talk about ......I don't understand my number 290403667 anymore. . .

I also have this information in QQ space.

Press the reset button on the left side of the instrument panel and the maintenance record will be reset to zero. After each maintenance is completed, the maintenance personnel will reset the maintenance prompts. It is not recommended that you reset it to zero on your own unless necessary.

1. Manual maintenance of the reset method of the lamp: press down and keep the zero button "A", at the same time press the brake, the ignition switch is twisted to "on", do not start the car, the character "INSP" will flash or the display screen flashes, continue to keep the zero button "A" until "...appears on the display, release the zero button "A", release the brake, the ignition switch is twisted back to the "off" state, and the zero work is over;

2. The method of resetting the maintenance light of the on-board computer: in the driving computer, the stool is set to open the setting menu, find the oil life option, and clear it after clicking on it to automatically reset;

3. Repair shop maintenance lamp reset method: use the car detector to connect the driving computer to reset the maintenance lamp.

The following is the method of resetting the Mercedes-Benz S350 maintenance light:

1. Turn off the ignition switch and press and hold the button on the right side of the dashboard. Turn on the ignition with the "Service" sign on the display, press and hold the button on the left side of the dashboard until the next maintenance mileage is displayed before releasing it;

2. You can use the car computer detector to zero, or you can reset it manually;

3. The specific zeroing method is as follows: put the ignition switch in the first gear. At the same time, press down and hold the "OK" button (S110S6) and the ** "Answer End" button on the right side of the multi-function steering wheel for about 5 seconds, at this time the instrument displays "VehicleDataRollerTest, AssystPlus, Workshop.

1. First click the one-key start button of the vehicle to start the vehicle engine, otherwise the maintenance light cannot be reset.

2. After that, click the Hunger Blade icon button on the right side of the multi-function steering wheel to adjust the display.

3. After that, the central display will display the maintenance interval date.

4. After that, click the CNCL button on the left side of the multi-function steering wheel.

5. After observing the vehicle dashboard, you can see that the maintenance lights have been changed and reset.