How to disassemble and repair the leakage at the rotating valve of the water heater?

1. Water valve leakage caused by rupture of water diaphragm. First of all, the water valve of the water heater should be disassembled, after dismantling, you can see that there is a water diaphragm made of plastic, this water diaphragm is used to push the water pressure, if it is broken, there will be water leakage of the water heater water valve, if it is because of this, you only need to buy the same type of water diaphragm, and then replace it. 2. The water valve pipe interface is damaged.

If the water valve leaks due to the damage of the water valve pipe interface, first close the main valve of the water inlet, then unscrew the hose fitting, remove the old connection, replace it with a new one, and then tighten it.

1. The water heater valve generally has two main functions, which are to control the inlet pipe of the water heater and control the pressure of the inner tank of the water heater. Controlling the water heater's inlet pipe can prevent the water from flowing in and wasting water when the water heater is being repaired or cleaned, resulting in a waste of water resources, and also facilitates the cleaning work. To control the pressure of the inner tank of the water heater, you can adjust the pressure in the inner tank of the water heater in time when you use the water heater in daily use, so as to avoid damage to the inner tank caused by excessive pressure.

2. If the water heater is not used for a long time, it is recommended to close the water valve of the water heater while turning off the power of the water heater, and drain the water in the water heater tank, which can avoid rust on the inner tank of the water heater to a certain extent, which will affect the service life of the water heater.

Maintenance method: 1. If there is a leak in the water heater valve or the connecting place, the water pipe interface should be loose and not tightened, or the raw material belt should be used again.

Wrapping and then gluing with adhesive can only be very effective for the water valve and joint where the water heater water pipe leaks. 2. In fact, the reason for the leakage of most water pipes is that the fittings or parts inside are permanent, resulting in looseness, and they are glued with raw material tape, or adhesive or glue. If you find that the water heater water pipe is leaking, it is because the connection between the water pipe joint and the water tank pipe is leaking, then the main reason is that the raw material belt is not wrapped well, causing water leakage.

3. One of the causes of water pipe leakage in the water heater is the connection between the water pipe and the joint. If this is the case, first of all, see what kind of water pipe it is, and if it is a plastic pipe, see whether the joint is tightened and sealed.

whether it is damaged, whether the screws are falling off, etc.; If it is a stainless steel hose, then it may be that the water pipe joint is loose or damaged; If it is a hot melt pipe, it is the water heater water pipe leakage caused by the hot melt not meeting the standard during installation. Here, warm reminder, when buying water heater water pipes, try to buy some water pipes, it is best to choose to install stainless steel hoses or plastic water pipes, whether the location of the installation workers to install the water pipes is accurate, this is very important, it is best to find a special manufacturer to install, or please a special installer. 4. In order to accurately find the location of the water heater water pipe leakage, it is necessary to understand the water heater pipes, not only the pipes of the water heater outlet, but also the water tank pipes, interfaces, etc.

If the water heater water pipe leaks from the water tank pipe and the connection place of the water tank, the usual way is either welding, or silicone sealing, if welding, the water tank needs to be reinstalled, if it is a silicone seal, just change the sealing ring.

Treat according to the leakage:

1. If the inlet valve is leaking, it may be that the joint is not treated, first turn off the inlet valve, drain the water in the water heater, remove the inlet pipe, if there is a crack, you can replace the new pipe fittings, and re-wind the raw meal belt to solve the problem.

2. If the water heater is safe and does not heat and leak, it may be that the safety valve is damaged, and the safety valve is replaced and the water is still leaking, and it may be necessary to install a pressure reducing valve.

Precautions for the use of electric water heaters:

1. First of all, when installing the water heater, a special ground wire should be used to make it safer and avoid leakage. In addition, when using the electric water heater for the first time, it needs to be filled with water to be heated by electricity, and do not boil it empty.

2. In order to ensure the safety of use, the power supply and socket should be regularly overhauled, and the problem should be repaired in time to avoid dangerous accidents. It is recommended that when the water heater is not in use, it is best to unplug it and turn it on in advance before use, which is power-saving and safe.

3. Pay attention to the setting temperature of the water heater, after all, people have different requirements for water temperature in different seasons. However, in summer, the temperature is high, and only warm water is needed for daily use. Therefore, the water temperature can be set at about 40 degrees Celsius to avoid excessive heating of the water heater and more electricity consumption.

The valve of the water heater is broken, and you can replace it yourself.

The technical term for an electric water heater outlet valve is a mixing valve. Generally, the mixing valve has two water inlets and one water outlet, and the water inlet.

One is the hot water inlet.

One is the cold water inlet, and the water outlet is the outlet for shower water.

Disassembling the mixing valve is actually very simple, and the steps are as follows:

1. Turn off the main cold water valve and the power supply of the water heater, 2. Open the mixing valve until there is no water flowing out.

3. Start to disassemble, pay attention to the high temperature of the hot water inlet, and be careful to avoid scalding.

After replacing the new valve, it is easier to install, how to disassemble and install, but also pay attention to the main water valve must be opened before powering on the water heater, and open the mixing valve until there is water flowing out of the hot water, you can close the mixing valve, and finally power on. Can.

Kiss! Hello, happy to answer your <>

How to repair the leakage of the pro-rotary valve: replace the new valve If there is a water leak in the connection position between the rotary valve and the pipeline, you can wrap a few more turns of self-adhesive tape around the connection position. Pay attention to the counterclockwise direction when winding, so that the valve is tightened more and more.

If the rotary valve itself is leaking, the valve should be opened and a sealing ring or O-ring should be added to the inside. If the treatment does not work, it is recommended to replace the valve with a new one. Here's how to deal with it:

If there is a water leak in the connection between the rotary valve and the pipe, you can wrap a few more turns of self-adhesive tape around the connection position. Pay attention to the counterclockwise direction when winding, so that the valve is tightened more and more. If the rotary valve itself is leaking, the valve should be opened and a sealing ring or O-ring should be added to the inside.

If you want to deal with an invalid wheel, it is recommended to replace it with a new valve. Hope mine can help you <>

Do you have any other questions?