Siemens washing machine shows that the door is opened, and the start button only flashes and does no

There may be several reasons why the start button of the washing machine does not respond, 1. The socket is not in good contact;

2. The door is not closed tightly, and the micro-delay switch is not in good contact;

3. The motor plug-in contact is poor or the motor is broken;

4. Tap the start button (the light will always be on after the start pause button is started), and there is a beep prompt;

5. The faucet is not turned on.

Solution: Socket problem.

Check the power supply motor drum plug and socket to see how the contact is good, if it is not good, you can use sandpaper to polish, or correct the spacing of the contact pieces to ensure contact.

Doors. In the energized state, check whether the micro delay switch is good, if it is good, it should be a contact problem, and the plug-in wire needs to be clamped again.

Poor contact of the motor plug-in wire.

It may be that the motor plug-in is loose, first re-reinforced, to see if the fault exists, no, replace the motor, generally can be handled.

Clicked the start button.

Press the start pause button directly again, and it will basically be in a normal state.

The faucet is not turning on.

You can turn the faucet back on and select the desired program again to start and let the washing machine run normally.

This phenomenon may be due to the fact that the door is not closed tightly, or it is not closed. You can just close the door again until you hear a click. Then when you press the start button, the door lock will click again.

If the fault still can't be solved, then it may be a problem with the door lock, or a problem with the motherboard.

If it's a problem with the door lock. After you press the time, the door can still be opened.

If it is a problem with the motherboard, after pressing the start button, the door will not open, but the machine still does not work. This is that the motherboard is not sending voltage to the door lock, causing the door lock not to work, so the motherboard does not detect that the door lock is closed, so it will not work.

The above two problems require professional theoretical foundation and rich maintenance experience. and specialized tools. If you are not competent, it is recommended to report for after-sales repair.

The washing machine does not work when the door is open, and if there are no other problems, it will continue to work if the door is closed.

1. The door lock is not locked.

2. There is a problem with the door lock or door hook.

1. It will be automatically unlocked one minute after the washing program.

2. Unlock the child lock, press and hold the reservation button to pause for 5 seconds, press and pause for 5 seconds in the E1 column, the lock sign is not lit, and it can be opened after waiting for 30 seconds.

3. Turn the knob to stop for 5 seconds and then turn it to any program, the door lock disappears, the E and X columns stop for 30 seconds and are automatically unlocked, and the M and S columns are directly unlocked.

4. There is a boom in the upper right corner of the bottom sewage outlet that can be forcibly unlocked by pulling it down directly.

Unable to operate normally or chaotic: After shutting down and restarting, it still cannot operate normally, usually because the main control board is broken and cannot run normally according to the program. It is recommended to contact the after-sales service, or professional maintenance personnel to check and repair. FYI.

If there is a problem, report to the brand after-sales technical support for door-to-door maintenance, and it is nonsense to ask here, a waste of time, and can not solve any fault problems.

Summary. The Siemens washing machine shows a key, which is a child lock, to prevent children from playing with the washing machine in danger, it needs to be unlocked, and there are two ways to unlock it:

1. Press the reservation button for more than 5 seconds.

2. Press the Start pause button for more than 5 seconds.

The door of the Siemens washing machine won't open, showing that a key keeps flashing.

Hello, I have seen your question and am sorting out the answer, please wait a while

Siemens laundry machine shows a key, that is a child lock, to prevent children from playing with the washing machine is dangerous, you need to unlock, there are two ways to unlock: 1. Press the appointment button for more than 5 seconds. 2. Press the start stool pause button for more than 5 seconds.

1. Press the reservation button for more than 5 seconds. 2. Press the Start pause button for more than 5 seconds.

Build it by appointment, and then it doesn't flash, and it still can't be opened.

Flash at the beginning.,After pressing, it won't flash.,Can't open it yet.。

This is not yet contacted, to the icon disappears to be considered to remove the child lock, you have to press the icon to disappear, is there water in the tube?

When there is boiling water in the barrel of a Siemens washing machine, the door of the washing machine cannot be opened. Therefore, it is necessary to select Sun Xuan to choose to dehydrate and completely drain the water in the washing machine, and then the unlocking step can be executed.

And so it is with other washes.

If the key unlocking is unsuccessful, if the Yuzu still can't open the washing machine door, it means that the washing machine door is blindly attacked and the lock is damaged or the motherboard grinding virtual brother circuit is faulty, it is recommended to contact the after-sales service for maintenance.

The Siemens washing machine door lock is flashing and won't start.

Hello! Siemens slag regret washing machine door lock flashing, can not start, first check whether there is a buzzing sound, or ticking sound, if there is a may be a loose belt in the beam cluster, there is no clutch problem, you can tighten the belt, adjust the clutch screw. If there is no sound, it may be that the motor or motor capacitor is broken, and the computer board is broken, so it is recommended to replace the electric machine immediately.

The Siemens washing machine door lock is flashing and won't start.

The door lock of the Siemens washing machine is flashing and cannot be started, it may be that the induction system of the washing machine is broken, it is recommended to turn off the power and try again. If it still doesn't work, you can try the following methods: 1. The door lock light is on, and water is also in, but not the drum Check whether the washing machine is heating and whether the belt is off, if not, check whether the electronic module is well plugged in and whether the electronic module is broken; Whether the motor wire strip is plugged in well and whether the motor is broken; Failure of pressure switch and heating pipe.

2.Do not spin dry, first of all, to see whether the micro delay is in poor contact, and secondly, check the position of the lead in the program controller, and whether the belt is worn, loose and broken; Whether the plug-in cable of the module and motor is not in good contact; module or weighing which motor is faulty; capacitive capacitance; The program controller is faulty or the plug-in contact is poor. The state is blocked.

Simon Peizizi drum washing machine.

The door closing sign keeps flashing, the switch button fails, and the reason and solution for not starting can not be started:

1. If there is a buzzing sound, or a ticking sound, it may be a loose belt of the washing machine or a clutch of the washing machine.

There is a problem; Solution: Tighten the belt and adjust the clutch screw.

2. If there is no sound, it is possible that the motor is broken, the motor capacitor is bad or the computer board is broken;

Solution: Replace the motor of the washing machine.

Summary. Hello! Reasons why the key of the Siemens washing machine keeps flashing and how to solve it, the key of the Siemens washing machine keeps flashing for the following reasons:

1. The door lock of the washing machine is not locked. 2. There is a problem with the door lock or door hook. 3. It will be automatically unlocked one minute after the washing program.

4. Unlock the child lock, press and hold the reservation button to pause for 5 seconds, press and pause for 5 seconds in the E1 column, the lock sign is not lit, and it can be opened after waiting for 30 seconds. 5. Turn the knob to stop for 5 seconds and then turn it to any program, the door lock disappears, the E and X columns stop for 30 seconds and are automatically unlocked, and the M and S columns are directly unlocked. 6. There is a boom in the upper right corner of the bottom sewage outlet that can be pulled down directly to force unlocking, and icons such as E1, E2, F2, or keys will appear

This is a fault**, indicating that the electrical appliance is faulty and the approximate location does not work properly. Since the faults of each appliance are different, you can take a look at the manual first. There is generally a fault ** table in it to see if there is such a fault and the corresponding fault prompt.

If you can't find it, or there is no manual, you can contact the after-sales service. If the warranty period has passed, or you have no professional maintenance knowledge and do not have the same accessories, you can ask an electrical repair shop to check and repair. 

Hello! The reasons and solutions for the fact that the key of the Siemens washing machine has been flashing for the following reasons: 1. The door lock of the washing machine is not locked.

2. There is a problem with the door lock or door hook. 3. It will be automatically unlocked one minute after the washing program. 4. Unlock the child lock, press and hold the reservation button to pause for 5 seconds, press and pause for 5 seconds in the E1 column, the lock sign is not lit, and it can be opened after waiting for 30 seconds.

5. Turn the knob to stop for 5 seconds and then turn it to any program, the door lock disappears, the E and X columns stop for 30 seconds and are automatically unlocked, and the old M and S columns are directly unlocked. 6. There is a boom in the upper right corner of the bottom sewage outlet that can be pulled down directly to force the unlocking of E1, E2, F2, or keys and other icons: this is a fault, indicating that the electrical appliance is faulty and the approximate part, can not work normally.

Since the faults of each appliance are different, you can take a look at the manual first. There is generally a fault ** table in it to see if there is such a fault and the corresponding fault is mentioned stupidly. If you can't find it, or there is no manual, you can contact the after-sales service.

If the warranty period has passed, or you have no professional maintenance knowledge and do not have the same accessories, you can ask an electrical repair shop to check and repair. 

Hello! The above are the reasons why the key of the Siemens washing machine keeps flashing and does not work and how to solve it.

Summary. There may be several reasons why the start button of the washing machine does not respond, 1. The socket is not in good contact;

2. The door is not closed tightly, and the micro-delay switch is not in good contact;

3. The motor plug-in contact is poor or the motor is broken;

4. Tap the start button (the light will always be on after the start pause button is started), and there is a beep prompt;

5. The faucet is not turned on.

The Siemens washing machine can't start, and as soon as you press it to start, the indicator light keeps flashing, what is it?

There may be several reasons why the start button of the washing machine does not respond, 1. The socket is not in good contact; 2. The door is not closed tightly, and the micro-delay switch is not in good contact; 3. The motor state is in poor contact with the plug-in wire or the motor is broken; 4. Tap and take the start button (the start pause button will be lit up after the light and sail balance is started), and there is a beep prompt; 5. The faucet is not turned on.

There's no problem, it's just that it doesn't start, and it ticks.

If there is a buzzing sound, or a ticking sound in Qizhou, it may be that the belt of the washing machine is loose or there is a problem with the clutch of the washing machine; Solution: Tighten the belt and adjust the clutch screw.

If it still doesn't work, it is better to call a professional to take a look.