The 54M wireless network is getting the network address

Someone else's mac is bound,Hit,Password admin,Try to enter the route no,If you can enter, modify the routing settings,The best way is to reset the landlord's route,Add your mac,You can get on。

Connected, but can't get online? That's the connection wireless password error.

The landlord has three wires, and it is best to set the channels for each wireless, such as: the first wireless is set to 1, the second is 6, and the third is 11.

The acceptable signal bandwidth is determined by the signal source, i.e. not because you have a big pipe, but because the opening of the pond pipe is so big. In addition, there are two situations where you have not been able to get the address: 1 Your router does not have DHCP turned on 2 You connect to a wireless router with a password, but you entered the password incorrectly when you connected.

1. Make sure that the wireless router has DHCP enabled, if DHCP is not enabled, the wireless connection cannot automatically obtain IP, and the wireless network card of M, if the connected wireless router is 54M, the maximum rate can only reach 54M.

Here's how to configure your router correctly:

After logging in, click on item 2 of the tree list on the left (depending on the router) "Setup Wizard", select your Internet access method, if it is home broadband, select item 2 PPPoE (ADSL virtual dialing), and then fill in your broadband account password point to save, and then the router prompts you to restart, wait for restart;

Select the encryption method of WPA-PSK WPA2-PSK, then set the wireless password and click Next, and the router is set up.

Select item 1 "Running Status" in the tree on the left, drop down to see the running status, if you can see the IP address (the above two settings can be used to observe the network connection status in this way), subnet, gateway, DNS and other items have numbers instead of blanks, you can be sure that the network has been connected;

Hello, since you are a telecom dial-up Internet access, please go to the router setup interface - setup wizard - select PPPoe virtual dialing option - enter the correct broadband account number and password - save and restart the router.

If the landlord dials up the Internet, then it can't be set to dynamic IP, it has to be set to PPPOE mode, and then set the dial-up account and password to the router.

Finally, find the MAC address clone on the left side of the router, clone the MAC of the router's WAN into the MAC of your computer, and prevent the telecom equipment from filtering the router and causing the router to be unable to access the network, which is very important and must be done.

If you use a wireless router to connect the cat, see if the interface is connected, and connect the LAN interface. Set it to wireless routing mode to try it.

This usually has to be poked with a needle or something, and held for a few seconds.

Second, the wireless basic setting belt will be changed to the maximum transmission of 300m to 54m. If the width of 4m or less can be changed to 11m. This increases the effective transmission of the signal.

Generally, the current home router only needs to set your Internet account and password, the default settings do not need to be changed, after you log in to the route (that is, you said the IP is or select the wizard mode in it, you can set it step by step.

If you haven't set up a network on your computer before, don't care about it, if you have set an IP address, you have to see if it's in the same network segment as the route, for example, if the route is your computer, it should be any number below 255 except for the last digit of the route).

Go to the Router Management page. On the left, select the IP bandwidth control option and click Enter.

Select IP bandwidth control, select line type, and add uplink and downlink network speeds. Save.

The conversion relationship of bandwidth is as follows: 1 Mbit/s = 1024 kbps; When selecting the broadband line type and filling in the bandwidth size, please select and fill in according to the actual situation, if you are not sure, please consult your broadband provider such as China Telecom, Netcom, etc.

If you don't want to restrict an IP, such as your own computer IP, you don't want to restrict it. But I want to limit the speed of other IPs.

Then according to the DHCP address pool, the start address is the end pool. Tick Enable Address Pools on Add New Entries to end the pool.

The minimum uplink and downlink are 0. Uplink max and downside max are added proportionally. Such as half of the total bandwidth.

In this way, half of the total bandwidth is occupied, and a total of 19 IPs share the other half of the total bandwidth.

In the IP bandwidth control, select Enable IP bandwidth control (tick), select your broadband type and bandwidth according to your bandwidth**, fill in the IP address you want to control, select your control mode (guarantee the minimum bandwidth or limit the maximum bandwidth), tick in the enable column, and fill in the bandwidth value you need to save.

It depends on whether this feature is available in your router.

In the router's broadband settings.

Now these things still need to be driven by hunger? It's all automatically installed by the computer.,If it can't be used,It's estimated that it's a setting problem to change this book.,The same can be automatically installed and sprinkled,Now almost all the numbers of the Fuyan code equipment will give you a drive CD,But the silver,For the current model,That's unnecessary,That's only for,The old products in the past,The current machine can be automatically and safely driven。 Why don't you try it yourself?

There are many things that you need to try yourself to understand more deeply.

1: The computer connected by wired connection is connected to the LAN port of the router, the network cable from the external network is connected to the WAN port of the router, and the wireless connection is connected to the router through the wireless function after the router is set.

3: If the username and password are correct, the browser will display the administrator mode screen, and a setup wizard page will pop up as shown below (if it does not pop up automatically, you can click the setup wizard menu on the left side of the administrator mode screen to activate it).

If it's not a monthly subscription, you'll have to think about it; After entering the account password; In the future, after your computer is turned on, it will automatically dial up to access the Internet. This means that you don't have to manually connect to broadband every time. If you don't want to automatically dial up the Internet, you can leave it out here;

5: Set a password for your wireless router to prevent others from stealing your network resources.

6: Wireless status: Turn the wireless function of the router on or off.

SSID: Set any string to identify your wireless network.

Frequency band bandwidth: Set the channel width occupied during wireless data transmission, the options are: 20m, 40m and automatic.

Maximum Send Rate: Set the maximum send rate for your router's wireless network.

Turn off wireless security: Turn off wireless security, which means that your router's wireless network is not encrypted.

WPA-PSK WPA2-PSK: The encryption method of your router's wireless network, if you select this option, enter the password you want to set in the PSK password, the password is 64 hexadecimal characters or 8-63 ASCII code characters.

Don't modify wireless security settings: Select this option to keep the last set parameter in the wireless security options. If you've never changed your wireless security settings, selecting this option will turn off wireless security at factory defaults.

If you change the wireless settings, the setup wizard will pop up as shown in the figure below, and click Restart to make the wireless settings take effect.

This situation is usually caused by the router not setting the Internet access parameters. You can exclude 1 by the following methods: check the line, whether the network cable of the cat is connected to the WAN port of the wireless router, whether the corresponding WAN light of the wireless router is flashing, and the flashing is connected.

2: Confirm the Internet ID and password, and carefully distinguish the case between the case. 3：