What does it mean when you go online and say that you are terminated by a remote computer

It's already logged in by someone else. Remote access is limited to one machine. If someone else visits, yours has to be terminated.

It should be that the remote computer is busy and unresponsive... Generally, it's good to try again after a while...

A computer connection terminated by a remote computer means that it has been disconnected from the other computer.

Workaround: Follow these steps:

1. Double-click the network from the control panel.

2. Click Services, click Routing & Remote Access, and then click Properties.

3. Click Port or if you want to enable to receive calls, click Configure, and then select the port that will receive calls for the RAS server.

4. Click OK, and then you will be prompted when you restart your computer.

1. There is an error in the operating system, and a prompt is being given, and the connection is being terminated by the remote computer in the process of verifying the username and password (error 629). Check Enable logging to view diagnostics.

2. Generally speaking, this is an error in the username and password, and it is terminated by the remote computer (network server).

3. If you use a router and you also set up autodialing, such an error will also occur, it is recommended to restart the router first, and press the reset key of the router if it is not possible.

4. If you also need automatic dialing, you need to enter the correct username and password. The steps are: Network Parameters WAN Port Settings WAN Port Connection Type Click on the drop-down menu Click PPPOE at this time the interface will change, there are Internet access, Internet password and other settings.

5. Finally, fill in the username and password correctly, and you can call the troubleshooting wizard, which is very effective. Run Enter (click OK to open the wizard): name

Broadband Error 629: The connection is terminated by the remote computer, which means that the port cannot be connected by the remote computer, and it is necessary to check whether the computer's equipment is running properly and whether the network configuration is intact. There are several reasons for this:

Second, if the broadband connector is problematic, you can try to dial out the broadband connector to clean it up and plug it back in correctly.

3. If you have a problem with the computer, you can try to turn off the computer and restart it, and then try to connect to the network.

Fourth, the problem of the router, check whether the router indicator is normal, the router is broken, this situation rarely happens, you can turn off the router and then restart it to try whether the network is normal.

5. If the network operator is overhauling the broadband in the area or is repairing the problem, in this case, you can call the operator's customer service ** to understand the situation and wait for the maintenance to be completed or repaired.

Broadband is terminated by a remote computer, and it may be that someone has maliciously hacked into your PC or trojanized your machine. Remedy: Stop telnet remote login, close port 23, cancel hard disk partition sharing, sweep and kill Trojans and patch them in time, change the password of the administrator account (especially administrator) to make it not empty and complicated, and deactivate the guest account.

Error Causes: 1. The Routing and Remote Access service is not configured to receive calls as a RAS server.

2. Network broadband is shut down in arrears.

Solution: 1. Double-click the network from the control panel.

2. Click Services, click Routing & Remote Access, and then click Properties.

3. Click Port or if you want to enable you to receive calls, click Configure, and then select the port to receive calls for the RAS server.

4. Click OK, and then the system prompts when you restart the computer.

5. Reconnect; Or reopen the control panel network connection and recreate the local connection.

1) If it is a problem with the broadband itself, first directly connect the broadband network cable to test, if it is a broadband problem, contact the broadband customer service to solve it.

2) If it's a problem with the router, if it can be used originally, it can't be used for the time being, my own practice is to disconnect the power of the router and plug it in, and I'll take a look. In there is a factory reset, it can be used from the new settings (this is under the premise of the correct physical connection, sometimes caused by the router's slow or failed IP address search, not that the router is broken).

If it can't be solved all the time, it is recommended to call the customer service of the router, they have **** guidance, I encounter a problem that I can't solve by myself, it is very useful to consult the advice they gave, and they will give the correct advice for your settings or operations.

3) If you turn off the wireless switch, turn it on, if it is a wireless connection with software, it is normal for the software to be difficult to use and often have problems, there is no better way, use a router. In addition, it is caused by the network card driver is not or is not suitable, and whether there is a problem with the network cable interface or network cable.

4) If it is caused by a system problem, it is recommended to restore the system or reinstall it.

If the remote computer terminates the connection, the connection will be lost, including all previous requests (the last successful remote connection is not counted). The remote connection needs to be completed with the permission of the remote computer, so if the remote computer terminates the connection, the connection must be restarted and cannot be continued. You can try reconnecting to the remote computer.

Causes: Unrecoverable Line Error, Noisy Line, Disconnected by System Administrator, Grip Strap Not Properly Negotiating with the Modem on the Remote Access Server at the Selected Speed.

If the redial error persists, slow down the connected modem and try redialing. You can simply try connecting to a different server to determine if the issue is related to the specific remote access server being called. Similarly, you can try connecting to the original server through another cable.