If I want to connect to a wireless router, what kind of router should I use and how do I connect it?

Nowadays, the household is generally tp-link, about 100 yuan, and the connection method is also simple.

1.Web page and cat connection.

2.The line that came out of the cat used to be connected to the computer, and now there is a route, and it is about to be connected to the route, usually the rightmost port (you observe the routing interface for specific conditions, some are next to each other, only the left and right one is some distance from the interface on the edge).

3. Open the browser, enter enter enter in the address bar and enter the routing setting interface.

4. Click on the left"Setup Wizard"Follow it step by step, it's very simple, it's to ask you to add a broadband account and password, and there is an option to choose PPOE

5.After the setup wizard is completed, click on the wireless parameters on the left side, and then simply set it according to the wireless setting part of the manual.

At this point, you will be able to search for wireless signals in this book.

I hope mine is helpful to you, and if you don't understand, you can continue to ask.

Any wireless router can be used.,Save a little bit on the *** buy a circuit board wireless router.,It's good to waste more than a hundred dollars to buy a netgear networkgear.,It's pretty good.。

When connecting, the incoming network cable on your dial-up modem is plugged into the WAN port, and the network cable port connected to the computer on the dial-up modem is plugged into the LAN port, and then turn on IE, enter, see the manual for the username and password, and set up PPPoE dial-up. The wireless password security settings are also in the manual.

There are a lot of people who use tp-link now, and it's not bad.

There is a wizard in the settings, but it should be noted that when filling in the user name, you must use a number calculator (found on the Internet) to calculate the real PPPOE that is connected to you, otherwise you will not be able to log in!

Remember to encrypt wirelessly and change your router's admin username and password!

Open the browser, enter enter enter in the address bar, and enter the route setting interface.

Click on the left"Setup Wizard"Follow it step by step, it's very simple, it's to ask you to add a broadband account and password, there is an option to choose the setting wizard after completion, and then click on the wireless parameters on the left, and then set it up simply according to the wireless setting part of the manual.

At this point, you will be able to search for wireless signals in this book.

TP-link, add a cheaper. Just configure it according to the manual.

It's all like this, and it's okay to go to Tao for a router of about 80 yuan.

I'm doing the same thing I did now. Specifically, let's talk about the settings:

1.First, do not connect to the external port, connect the wireless router to the desktop (the wireless router LAN port is connected to the desktop), enter it in the browser, and log in to your wireless router.

2.Change the IP address of the wireless router on the LAN port to avoid conflict with the IP address of your downstairs neighbor router.

3.Set the WAN port IP to Static, IP

Submask, the IP of the original inbound line of the gateway to the Internet normally), DNS you should know, do not know the online check or ask the network service provider.

4.Disable the DHCP service.

The downstairs network cable can be connected to the WAN port or LAN port of your wireless router, and if you connect to the WAN port, your computer IP should be set static, which is more troublesome. You just connect the LAN port, and then your PC is also connected to the LAN port of the wireless router, which is automatically used for wireless and IP, and the wireless router is used as a switch. But it's easy to set up, you can set it up this way.

Of course, because your wireless router IP has been changed, if you want to log in later, you have to change your computer's IP first.

Gateway instead. Otherwise you won't be able to log in to your wireless router.

There's no need to use a wireless route.,Just connect the cat and the wireless router.,But you have to set up a wireless route.,If you can't set it up, you can hi me.。

Set Route 3:

The first trick: only need LAN 1 cable to connect to the computer; (The original router's network cable does not need to be connected) The second trick: enter in the browser address bar, press enter, enter the username and password on the back of the router (usually admin), and access the router interface.

The third trick: network parameters - IP address changed to: save (generally wait for about 1-2 minutes, the page jumps and cannot log in) - restart the computer and router (unplug the wire) The fourth trick:

Enter in the address bar of the browser, press Enter, enter the username and password on the back of the router (usually admin), and access the router interface.

3 hours) - set the password (ssid: display the name when searching for unlimited searches, change it or not, and don't move the rest) - next - save - prompt four successful sixth tricks: network parameters - mac address clone - clone - save the seventh trick:

System Administration - Reboot the router.

The eighth trick: access the network cable from the existing router to the WAN interface The ninth trick: open the web page - applause.

You now have four routers, two of which are wireless. I'm sorry for you.

You can change your scheme.

The telecom cat is directly connected to the wireless router, and all computers that do not support wifi buy a wireless network card, and there are more than 30 wireless network cards. Buy a wireless router a little better, you can go through the wall.

Buy a wireless router with relay function.

When installing a wireless router, you need to prepare two network cables:

The first is the broadband user network cable, and the second is the network cable sent by the router.

Wireless Router Installation Steps:

1.Change the local connection to automatically obtain the IP address.

2.The network cable that comes out of the "modem" is connected to the "wan" port on the router, and the router's ports (1,2,3,4) are either connected to the network cable port behind the computer host.

3.Open the browser and enter the password and username of the router are admin4Go to the router settings screen, select the PPPoE (ADSL virtual dialing) method, enter your home account and password, and confirm.

5.Then set the SSID, encryption method, and password.

6.Save, restart. The router is set up!

The signal of the wireless router at home is not good, and you need to add a wireless router how to connect and set up.

Plug the cat's network cable into the WAN port of the router, and plug the network cable of the computer into the network cable interface marked with the number (whichever one you want).

The operation steps for connecting multiple wireless finchs are as follows:

1. Router connection:

1. Wireless bridging: If several routers support wireless and WDS functions, wireless bridging can be carried out. However, this method is not recommended because it has certain requirements for signals, equipment, and environment.

2. Wired bridging: Several wireless routers are connected to the LAN ports of both parties through network cables.

Second, the router settings:

1. Enter the IP address of the router: run the browser on the computer, enter the IP address of the router in the address bar (you can refer to the router manual or check the instructions on the nameplate on the back of the router), such as: , and press Enter.

2. Log in to the router: After entering the router login interface, enter the login account and password (you can refer to the router manual or check the instructions on the nameplate on the back of the router), generally: admin or boot.

3. Set up the router: The common settings are mainly as follows.

a. Enter the Internet access account and password of automatic dialing. After entering the settings interface of the main router (not required for the secondary router), click "Network Parameters" on the left, select the Internet mode PPPoE dial-up, and then enter the account number and password provided by the network service provider, and save it. In this way, the Internet can be automatically dialed up through the router.

b. Set DHCP.

Main router: Select the DHCP server tab, click "Enable" DHCP, set the IP address (the start address and end address of the address pool can be set by default, and the maximum limit is generally reserved as the gateway and broadcast address respectively), the gateway (generally the IP address of the router such as the server address in this example (the DNS server address applicable to different regions is different, it is best to follow the settings provided by the network service provider, You can also set it to the public DNS server provided above) and save it. In this way, computers that are not connected to this router do not need to manually set parameters such as IP addresses, and can automatically obtain parameters such as IP addresses.

Secondary router: Select the DHCP Server tab, click "Do Not Enable" DHCP, and save it.

c. Set a wireless password. In order to prevent other users from illegally accessing the network, you need to set a wireless password. Click "Wireless Settings" - "Wireless Security Settings", select the appropriate encryption method, and set a password of more than 8 digits.

Save it at the end. Multiple routers need to set a wireless password, which can be the same or different.

d. Change the router login password. Because the router is set with a default universal account and password, it is generally admin or boot.

Any computer connected to the router can log in to the router and even tamper with the router parameters, so you can go to: Security Settings - Change Login Password to change the default password to a custom password.

4) Restart the router: After the setting is completed, you need to restart the router to take effect, restart the method, under the system tools, select the item "Restart the router".

aThe router is set up normally, and it is OK to be able to access the Internet.

bThe router operates as follows:

2, Then reconnect, open DHPC settings, turn off DHCP service, save, restart.

3, then reconnect, open Wireless Settings - Basic Settings. Modify the SSID name, which cannot be the same as A, and then click Scan to find the SSID of Router A, select, and enter the connection password to connect Router A. Most importantly, tick the "Turn on WDS" checkbox, save, and restart.

4. After restarting, the bridge is successful, and you can connect to the A router through the B router wirelessly.

This is simple, the first route is dynamic IP Internet access, then find the network parameters in the left dish LAN port setting - change this parameter to, note: is it not, if it is equal to not changing, or can not access the Internet. In the future, you will need to use the modified parameter to log in to this route.

Network cable connection: The network cable from eSurfing is connected to the WAN port of the router.

If you divide another route from the route, you have to change the gateway to another router, and you must have a different network segment to access the Internet anyway.

The router is connected to the wireless router, and the second router (wireless router) is set up, there are two ways (provided that the wired router has been set up):

The first method: dynamic IP mode (the first route is the primary route, and the second route is the slave route).

1. Plug in the router and do not connect the LAN port of the main router first, and reset the slave router (restore the factory);

2. Connect the computer from any LAN port of the router to enter the settings page;

3. Set according to the dynamic IP;

4. Then set the SSID, encryption method and password;

5. Save and restart;

6. After setting, connect the network cable from the LAN port of the main router to the WAN port from the router.

The second method: wireless AP mode.

1. Connect the computer to the LAN port of the router first, and change the IP address of the slave router. For example, most router addresses are, we just need to change from router IP address to that;

2. Turn off the DHCP function from the router in the settings;

3. Finally, connect the network cable from the main router to the LAN port of the slave router (any one is fine), note that it cannot be the WAN port.