Water purifier installation 20, how to install water purifier

The general unit has a technician to install, you buy it in **, then the unit should give you free installation, our unit is like this I don't know about other units.

The installation method of the water purifier is as follows:

1. The host is well connected with the filter element, which is convenient for later use.

2. Load the RO membrane, and use an appropriate wrench to screw the joints and filter bottles.

3. Load the RO membrane, use an appropriate wrench to screw the joints and filter bottles, do not rotate too tightly, it is easy to crack.

4. Install the faucet to the appropriate position of the faucet, and then put the faucet on the hole of the sink after loading the gasket into the spindle of the faucet head, and fix it.

5. Fix the faucet, and then insert the 2 water pipes into the connection port with the faucet.

6. Cut the appropriate water pipes, and connect the raw water, pure water, pressure barrels, and waste water pipes respectively.

7. Close the main valve of water inlet, and install the water inlet tee and 2-point ball valve.

8. Connect the main machine with the pressure barrel first, then connect the main machine with the water inlet, cut the pipe of appropriate length to connect it to the wastewater outlet, connect the other end with the sewer, and then fix the waste pipe with a cable tie.

9. Straighten out the connected water pipes and tie them with cable ties.

Precautions for the use of water purifiers:

1. The water purifier should be kept in a moist state after each use, and water should be added in time to improve if it is dry, because it will lead to a significant decrease in water production.

2. The water purifier should not be used for three consecutive days, and it should be cleaned first when used again, and it is best to rinse it two or three times repeatedly, and then discharge the remaining water into it for reuse to ensure water safety and drink healthy water.

3. If the tap water is stopped, the remaining water should be drained, and the water should be released for reuse, and the sediment and rust in the water pipe should be drained before being reused.

4. The water yield of the water purifier has a close relationship with the water quality, such as the water is better, the water yield increases, on the contrary, the water quality is poor, the water yield decreases, so the water quality is tested according to the water production.

5. When the water purifier is used, frequent cleaning can effectively prolong the service life, so don't forget to clean the water purifier.

6. If you don't use the water purifier for a long time, you should keep it well, and don't let the dirt remain in it for too long, so as not to affect the water quality when you use it later.

Water purifier only installation method:Tools Material: Eggplant water purifier, wrench.

Method Steps:1. Pinch the nut of the faucet with your fingers, rotate clockwise, remove the nut of the faucet, if you need the nut in the future, pay attention to keep the nut.

2. Take out the coarse thread joint and gasket of the inner tooth, and put the gasket into the thread of the coarse thread vibratory joint of the inner tooth, so as to prevent water leakage.

3. Twist the nut of the water purifier, put the coarse threaded joint of the inner tooth into the nut, and lock the joint with the faucet.

4. Connect and lock the corresponding interface of the main part of the water purifier with the nut, and be sure to tighten it to ensure that there is no air leakage in the seal.

5. If it is the first time to use it, remove the packaging plastic film of the filter element.

With the improvement of living standards, modern people are more and more pursuing quality life, because drinking water safety and health are closely related, so more and more families have installed water purifiers. Today, PCHOUSE will talk to you about how to install a water purifier.

The first step is to open the box and check that the spare parts are complete.

The second step is to connect the main unit of the water purifier and the pre-filter element.

Use a pre-filter wrench to unscrew the filter cap, install the corresponding filter cartridge in turn, and tighten the cap.

The third step is to install the RO membrane filter.

Open the host panel - unplug the monitor interface on the panel - unscrew the filter cover - tighten the cover after inserting the RO membrane - connect the monitor interface and cover the panel.

The fourth step is to connect the PP pipe to various interfaces on the host.

Cut the PP pipe into appropriate four sections - remove the buckle and plug on the main unit interface - insert the cut PP tube separately and then install the buckle that has just been removed.

Note: Pay attention to the flat incision when cutting the PP pipe).

Step 5: Connect the pressure barrel.

Take out the pressure barrel, install the small ball valve of the pressure barrel at the inlet and outlet of the pressure barrel, and connect the PP pipe at one end of the water inlet.

Step 6: Install the faucet.

Install the gasket into the faucet spindle in turn, place the faucet at the sink hole, and tighten the nut. After fixing the faucet, insert the 2-point PP water pipe into the faucet connection.

Note: The connection between the 2-point PP pipe and the faucet must be installed in place, and the length of the 2-point PP pipe is appropriate).

Step 7: Connect the water inlet.

Close the main valve of the water inlet, and install the water inlet tee and the connecting ball valve.

Note: The hot and cold water inlet pipe must not be mistaken, and the water inlet of the RO machine is cold water. Check the water pressure before installation, such as higher than the ** pressure reducing valve device).

Step 8: Fix the host.

Use the water purifier hanging plate, screws and other spare parts to fix the host in a suitable position.

Step 9: Organize the water pipes.

Straighten out the connected water pipes and tie them with cable ties.

Note: Be sure to carefully check whether the water pipes are straightened out to prevent water pipes from being discounted);

Step 10: Debugging.

Place the pressure bucket and the main unit, plug in the power supply and turn on the water source. Open the pressure barrel ball valve and check whether the joint nut is leaking for water debugging. Turn on the water source and the gooseneck faucet, turn off the gooseneck faucet when the water comes out, and check for leaks (wipe each connector with a paper towel you carry).

A good water purifier can improve water quality and be more beneficial to our health, I hope you can buy it on demand.

To install the water purifier, you must first check whether the spare parts are complete, and then connect the main machine and the filter element well. Install the RO membrane, screw the fittings and the filter bottle at the same time, remove the pressure bucket and install the pressure bucket ball valve at the water inlet. After connecting the blue sections of each part of the water purifier with the water pipe, straighten out the water pipes, and then turn on the power to adjust the time.

1. To install the water purifier, first check whether the spare parts are complete, then connect the host and the filter element, and then install the RO membrane, and at the same time use a suitable wrench to screw each joint and filter bottle. After the pressure drum is taken out, install the small ball valve of the pressure drum behind the inlet and outlet of the pressure bucket.

2. Install the faucet in the appropriate position of the water pipe, then fix the water faucet, and then insert the 2 water pipes into the connection port with the faucet. Cut the appropriate water pipes to connect the raw water, pure water, pressure barrel and waste water pipes respectively, and then close the main water inlet valve, and install the water inlet tee and 2-point ball valve at the same time. Check the water pressure before installation, if the water pressure is higher, you need to install a pressure reducing valve device.

3. After connecting the main engine and the pressure barrel, connect the main engine with the water inlet, then cut the appropriate length of the pipe to connect the wastewater outlet, connect the other end with the sewer, and then fix the waste pipe with a cable tie. Finally, after straightening out each water pipe and tying it with a cable tie, turn on the power supply for debugging.