How to place the switch in the weak well and how to connect the network switch in the weak well cabi

Updated on technology 2024-02-08
14 answers
  1. Anonymous users2024-02-05

    Weak current wells can also be placed in network cabinets, if there is only one on each floor, you can put a small cabinet, the standard 19-inch cabinet height of 10 U is enough, ** hundreds or so, the brand of this small cabinet does not matter to see the workmanship.

    If possible, install anti-static flooring.

    Downstairs, you're not right.

    The standard cabinet refers to the width of the cabinet of 19 inches instead of the height, the height can be 18U 32U, and the 2-meter cabinet you say is 42U.

    allen8023cjj |Level 2.

    Upstairs, it is said that the standard cabinet is a 2m cabinet, how can it only be more than 10 U.

    Do you only have one switch and no other equipment? How do you get PDS? Don't use a cabinet? Calculated, these always have to be put together, and there are also wall-mounted cabinets, depending on the space in the weak current room.

    pds ?Big brother: Explain what kind of device is PDS? pdu +ups ?

  2. Anonymous users2024-02-04

    Then it depends on whether the size of your switch can be put into the weak current well, the switch is in the weak current well, the left and right sides of the switch and the back of the switch should be not less than 20cm away from the wall, and there should be space for heat dissipation. There should be wiring operation space in front, not less than 80cmCustomize the switch according to the above conditions.

    But the installation should be firm and reliable. No strong electricity enters the weak well.

  3. Anonymous users2024-02-03

    Generally, a wall-mounted cabinet can be placed on several floors, and the specific height depends on the number of switches, and the width * depth is about 600*450

  4. Anonymous users2024-02-02

    There should be a cable management frame and a patch panel, the bus into the switch, and the switch to the patch panel.

  5. Anonymous users2024-02-01

    Go to the forum to find a typical installation diagram of the cabinet.

  6. Anonymous users2024-01-31

    And, of course, heat and humidity.

    will cause damage to the equipment.

  7. Anonymous users2024-01-30

    Ordinary switches do not have dustproof functions, but weak current wells with a less harsh environment should not be a big problem.

  8. Anonymous users2024-01-29

    It is best to do dustproof treatment on the ground. If it's not important, you can use it casually.

  9. Anonymous users2024-01-28

    At least 6 switches on the sixth floor of the weak current well should be connected to the equipment room through optical brazing.

    The equipment room requires a switch with at least 6 optical ports to converge, and optical modules must be inserted on both sides of the switch in the equipment room and the weak current well.

  10. Anonymous users2024-01-27

    Generally, it can be connected with a network cable, and the PoE switch can be powered separately.

  11. Anonymous users2024-01-26

    I don't know the incoming room, it may refer to the weak current incoming room of the building.

    The wiring room refers to the room where the weak current converges distributed on each floor, and the weak point well refers to the weak vertical pipeline of the building. To use an analogy, the wiring room is the ribs, and the weak electric well is the spine.

    After pulling the cable from the terminal point to the computer room, you need to play the distribution frame, the front of the distribution frame is the RJ45 interface, and the back is the module port. The line from the terminal hits the module port at the back. The front RJ45 is connected to the switch with an ordinary network cable, so that all terminal points are connected together through the switch to form a local area network.

    The router is on top of the switch, the switch is connected to the router, and the router is connected to the external network, so that the computer in the LAN can be connected to the external network.

    Next time, remember to give points. Otherwise, no one would want to answer your kind of question.

  12. Anonymous users2024-01-25

    Just add a small TP-Link switch!

  13. Anonymous users2024-01-24

    The weak current is the router, and the merchant is the switch.

  14. Anonymous users2024-01-23

    To put it simply, you can add a switch to the network within the merchant.

Related questions
23 answers2024-02-08

Rounded corners can be set using the Mesh Smoothing modifier and the Material to Shader.