How thick is the cement floor glue, and how thick is the tile floor glue

Dear, I'm glad to answer for you: how thick is the tile floor glue; Hello Kiss Tile floor adhesive is generally thick of 2cm Oh 1, tile adhesive do not mix cement, sand and other things Tile adhesive does not need to add other things, if added will destroy the proportion of the product, the quality can not be guaranteed, and the tile is prone to hollowing, falling off and other problems. 2. Do not put the tile adhesive on the ground and stir it with a shovel, because placing it on the ground will lead to the loss of the effective chemical components of the tile adhesive; Secondly, it is impossible to mix evenly with a shovel, and the proportion of water added to manual stirring is difficult to be accurate, which changes the ratio of materials and leads to a decrease in adhesion.

3. Do not put the tile adhesive in a bucket and soak it with water, and use the method of soaking cement to soak the tile adhesive will cause the tile adhesive to have no adhesive strength, and cause the tile to fall off in the later stage. 4. The use time should not be too long, and the use of water should not be added, and the addition of water to tile adhesive will lead to insufficient bonding strength in the later stage; Tile adhesive should be used with stirring, the use time should be controlled within 2 hours, and it should be discarded after drying. I hope my answer is helpful to you, if there is anything you don't understand, you can leave a message.

Finally, I wish you good health and a good mood! <>

Dear, hello, I am glad to answer for you how thick the tile floor adhesive is generally 1The back-adhesive method involves applying a tile adhesive to the back of the tile and then applying it to the base layer. At present, most of the tile adhesives use this method, because this is the traditional ceramic tile adhesive method.

The thickness of the tile adhesive layer is about The trowel method refers to the use of a toothed spatula to scrape the tile adhesive batch to the surface of the base layer to be pasted with a toothed spatula, and then comb it with a toothed spatula to form a mortar layer with raised stripes and uniform thickness, and then press the tile on top of it and twist slightly, the thickness of the tile adhesive layer is about The combination method refers to the combination of the back adhesive method and the trowel method for construction, that is, the tile adhesive is scraped to the surface of the base layer to be pasted with the trowel method to form a mortar layer with raised stripes and uniform thickness. Then apply a thin layer of tile adhesive on the back of the tile, and then paste the tile on the base layer with wet wetland, and the thickness of the tile adhesive layer is about 3-5mm.

Summary. Dear, I'm honored to have your question The information that the teacher found for you here is: Is it good to lay glue on the mastic floor:

The mastic floor is well paved with glue. The advantage of laying floor glue is that it is good to clean and hygienic, but it is best not to lay floor glue in more humid areas, because the floor glue is not breathable, and the chassis will rust with moisture, and the gain outweighs the loss. Now car decoration stores have that kind of large enveloping mats, which can also be used as floor glue, just buy one.

The floor is still better, mainly used to protect the tiles, or to protect the floor, but to choose the environmental protection is better, if there is a parking space to release formaldehyde, do not buy.

Dear, I'm honored to have your question The information that the teacher found for you here is: Is it good to lay the glue on the mastic floor: It is good to lay the glue on the mastic floor.

The advantage of laying floor glue is that it is good to clean and hygienic, but it is best not to lay floor glue in more humid areas, because the floor glue is not breathable, and the chassis will rust with moisture, and the gain outweighs the loss. Now car decoration stores have that kind of large enveloping mats, which can also be used as floor glue, just buy one. The floor is still better, mainly used to protect the tiles, or to protect the floor, but to choose the environmental protection is better, if there is a parking space to release formaldehyde, do not buy.

Recommendations <>

Now that the epidemic is repeated, you must pay attention to safety when you go out, <> go out, wear a mask, wash your hands frequently! Have a great day, <>

Paste the mastic floor tiles, paste 2 cm thick, how thick the ground is wiped, and how thick the bricks are appropriate.

Before attaching the floor tiles, the ground needs to be smoothed and cleaned. For 2 cm thick floor tiles, it is recommended to apply a layer of cement mortar with a thickness of between 1-2 cm. After the floor tiles are attached to the cement mortar, a thin layer of cement with a thickness of between 1-2 mm needs to be applied to the bricks to ensure a tight bond between the floor tiles and the cement mortar.

After sufficient drying, this calming construction method ensures that the floor tiles are installed firmly and have a long service life.

1. Measure the size.

Measure the size of the room, this should be as accurate as possible, and then cut according to the measured size, of course, pay attention to the size of the cut is slightly larger than the measured size.

2. Indoor processing.

Before paving, the ground should be cleaned, and the oil stains or dust and sand on the ground should be removed, followed by the leveling or uneven shoveling, and then leveling with a spatula.

3. Gluing. Gluing this is the process before paving, gluing should be glued on the ground according to the size of the floor leather, one by one, and 10 cm should be left at the seam not coated, so as to facilitate the seams behind.

4. Pave the floor.

When the glue is coated, it is necessary to pave it, and when it is paved, it should be carried out one by one, pressing while paving, and driving away the bubbles. The joints of the floor should generally be collaged in an overlapping way, and it is better to overlap 5cm. Use a long steel ruler to align with the overlap, cut along the plate ruler, then remove the cut edge strips, brush the appropriate amount of glue at the seam position with a paint brush, and then use a pressure roller to close and compact the joints.

The residual glue extruded from the seam should be wiped clean to save the impact on the appearance. Then apply a thin layer along the seam with seam fluid.

5. Inspect the work.

Check for air bubbles and flatness, and if there are air bubbles, you can use a syringe insert to suck out the air and then compact it. Use laundry detergent to remove any remaining glue marks on the floor leather; If it can't be removed, wipe it off with alcohol.