Is it better to connect the network from the optical modem to the switch or the router to enter the

Of course, it is better for the network to enter the room from the optical modem to the switch, because this not only saves the money of the router, but also the network speed will become faster, and the user's network latency will not be high. It depends on what mode you have, and you also need to ask the operator what mode the modem configuration is.

It is better to connect the network to the router from the optical modem, because after connecting to the router, you can transmit wifi signals, and mobile phones, including laptops, can also be directly connected to wifi. If you are a switch, you will not be able to use wifi.

Router. Because the optical modem is connected to the router and enters the room, it is more convenient to manage in the future, so it is better to connect to the router.

Both. 1. Connected to the cat, the computer needs to enter the account password first, and if you don't need the account password, you can link it directly.

2. Connected to the router, you need to set up the router first, after the router is connected to the network, the network cable is plugged into the router, and the computer can directly access the Internet, no need to log in to the broadband account.

3. A network cable needs to be connected between the modem and the router.

4. If it is a wired router, then a network cable is also needed between the router and the computer.

Light cats. You can connect to a router or a switch in the back, depending on the requirements.

The router is connected to the back of the optical modem, and the router is set up as follows:

1. Plug the network cable (bus) of the optical modem into the wireless router.

, plug one end into any LAN port of the wireless router with a network cable and connect the computer network card at the other end.

Power on your router.

3. Then enter admin, the default account name and password are the same (there is also a prompt for the original data on the back of the router) to confirm.

4. After entering the wireless router setting interface, select the Internet access method according to the setup wizard (different broadband options are also different), and enter the Internet access and password.

5. Save, continue to set the wireless key, and then you can surf the Internet normally.

6. If it is abnormal, you may wish to click the reset button of the wireless router and set up the router again.

If it is an optical fiber modem that needs to be dialed up, the optical fiber modem must be connected to the wireless router, and the wireless router must be connected to the switch, and the optical fiber modem must be connected to the wireless router according to the following method:

1. Plug in the wireless router, don't connect the cat first, and connect the computer to any LAN port of the wireless router.

Enter the IP address of the router in the address bar of the browser (on the label behind the router), and enter the login username and password to enter the settings page;

3. Set up according to PPPoE (ADSL virtual dialing), enter the Internet access and password;

4. Set the SSID, encryption method and .

Password; 5. Save and restart;

6. After setting, connect the network cable from the cat LAN port to the WAN port of the wireless router.

The first type of switch can be in front of the router, but it can only be used in two places separately, and cannot be dialed at the same time; In addition to the IPTV of the TV

Need to connect directly to the TV,Unless there are two network cables from the Guangmao to the TV at the same time, one is connected to the TV,One to the router。。。 The second is also a problem ... The IPTV that comes out of Guangmao should be directly connected to TV, and it can no longer be connected to TV through the router, so IPTV from Guangmao

directly to the TV, and a line to connect to the wireless router;

What do you do when you connect to a switch?

Connect to the switch, then you can only use it with only one account! It doesn't make any sense!

Unless there are n lines, so that the switch can group n lines together!

If it's just one line, don't think about it! (Jinan Weigao network, wireless coverage equipment and overall network coverage equipment are provided).

Generally, routers also support multi-line access! Therefore, there is only a line that does not exceed the WAN port of the router, so there is no need to add a switch in front!

If you have any questions, let's ask! Hope!