How to set the parameters of the wireless router connected to the optical modem?

Home Network Environment Cabling:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Router Settings:

1. Check the router management address on the router shell label, there are two types of management addresses, please be sure to fill in the actual information. After entering the address in the browser, set the administrator password, and continue to set it (the default username and password of some routers is admin);

2. After entering the management interface, click Next to start the setup wizard, and select PPPoE (ADSL virtual dialing) in the Internet mode;

3. Enter the broadband account provided by the broadband operator in the Internet account and the broadband password in the Internet password;

4. Wireless settings: Set the wireless network name in the SSID, and set the wireless password of no less than 8 digits in the PSK password (it is recommended not to set the SSID to Chinese or special characters.) If the PSK password is set to 8 digits or more, be case-sensitive. ）；

5. Click Done, and the router is set up successfully. At this time, the computer that needs to access the Internet only needs to connect to the router LAN port or wireless network, and can access the Internet without any settings.

Use Wi-Fi!

You can configure it according to the manual.

The following describes how to connect a router to an optical modem:

1. The router generally has a power supply, WAN, LAN several ports, first make the router connect to the power supply, and then let the network port of the optical modem and the router WAN port be connected by a network cable, and the computer network cable is connected to the LAN interface of the router, at this time, the WAN light on the router will flash, proving that there is a signal source.

2. Then open the browser, enter the IP address of the brand router in the address bar, and enter the login password after entering the login page.

3. Then enter the settings interface of the router, click [Internet Settings], enter the broadband and password, where the bandwidth and password are provided by the network operator.

4. Finally, click [Wireless Settings], set the name and password of the router, and you can start surfing the Internet.

Introduction to routers

A router (also known as a pathfinder) is a computer network device that can send data to a destination by packaging a network (selecting the transmission path of data), a process called routing. A router is a device that connects two or more separate networks, and routing works at the third layer of the OSI model, the network layer.

A router is a device that connects various LANs and WANs on the Internet, and it will automatically select and set routes according to the situation of the channel, and send signals in the order of the best path. The router is the hub of the Internet and the "traffic police".

At present, routers have been widely used in all walks of life, and various products of different grades have become the main force to realize the internal connection of various backbone networks, the interconnection between backbone networks, and the interconnection between backbone networks and the Internet.

Now the community is generally covered with optical fiber, if you want to use a wireless router to surf the Internet, then the setting method is different from the setting method of using ordinary broadband cats!

Because the IP addresses of many fiber modems are also the same, and the IP addresses of TP-Link wireless routers are usually the same, so there are conflicting IP addresses.

The first step is to link the line according to the connection method between the router and the cat.

The second step is to enter in the IE browser, and the password and password are admin.

Since the address of the fiber modem and the wireless router is the same, it will cause an address conflict, so you need to modify the address of the router, set the LAN in the network parameters, modify the IP address as shown in the figure, click Save, and restart the router.

Once saved, restart the router. Close the browser, reopen the browser page, and enter the IP address you just changed. Enter the username and password as well.

The third step, click "Select dynamic IP, let the wireless router automatically obtain the IP address of the fiber optic modem" is OK for telecom broadband, but Unicom home broadband is dial-up Internet access, so you need to choose PPPoE (ADSL virtual dialing), here you will be asked to enter your account and password, which can be found on the CD provided to you by Unicom, and the password must be modified to your own.

Turn on wireless security and set your own password.

Gateway: The IP of the modem is the packet mtu: 1500-DNS server: Set the IP of the modem.

As we all know, now is a network era, every household is inseparable from it, in order to make the network faster, generally speaking, there will be two kinds of equipment in the home: router and optical modem. Let's introduce to you how to set up the optical modem to connect to the router.

1. First of all, you need to log in to the ** of the optical modem, and then you can enter the administrator password.

2. After logging in, find the Internet access settings and click on the common settings.

3. At this time, you should enter the broadband and password, save it, and connect the modem and the router to the Internet.

What are the precautions for installing and using optical modems?

1. Before installation, when choosing a light cat with better performance, you must not be greedy for a small bargain, to buy some cheap ones, and the quality is not good, this kind of problem will occur when you use it, it is best to choose some famous brands, which are more secure.

2. When installing, be sure to connect the network cable in the right position, or there is no way to access the Internet, if you don't know how to connect, it is best to find a professional to pick it up.

3. When using the optical modem, don't switch it often, you should know that frequent switching will also affect its performance, and there may be a phenomenon that you can't access the Internet, so you only need to keep the switch state at ordinary times.

4. You should also put the optical cat box in the correct position, you can't put it directly on the ground, if you put it on the ground, you may touch the optical modem, and it will cause the network cable to loosen if you are not careful, which will affect the effect of surfing the Internet.

5. If you find that the Internet speed is not fast, there may be some faults at this time, and it needs to be replaced, or a professional can be asked to check it.

Summary:About how to set up the router of the optical cat rental boy is introduced here,Follow the above steps to set it up,It must not be sloppy when setting。 If you want to know more about related information, please pay attention to Qeeka Home.

In this Internet age, almost every household has a wireless network, and with it, the family can enjoy free Internet. However, to install a wireless network, you must first connect the router to the modem and set it up. So, how to set up the router light receiving modem?

What are the advantages of a wireless LAN? Let's take you to find out.

Use one network cable to connect the modem port to the router, and then use another network cable to connect the computer device to the router LAN port. When the light on the router's WAN port starts flashing, there is a signal source. Then enter it into the browser, and then enter the router password to enter the settings interface to set up.

Advantages of wireless LAN.

1. Flexibility and mobility.

For wired networks, the location of its installation will be greatly limited by the location of the network, while for wireless networks, it can be installed anywhere in the domain of the signal coverage area. For wireless LANs, its biggest advantage is the celebration of mobility.

2. Easy to install.

The installation of wireless LAN will be more convenient, which can reduce the workload of network wiring. Usually, it is only necessary to install more than one access point device, and it can establish a local area network throughout the region.

3. Easy to plan and adjust the network.

For office locations, if you want to rebuild the network, the wired network is not only expensive, but also very time-consuming, and the installation process is very cumbersome. This is not the case with wireless LANs, which can reduce the occurrence of this situation.

4. Easy fault location.

In the process of using the wireless network, it will be easier to locate if there is a fault, and only need to replace the relevant equipment. Wired networks, on the other hand, are difficult to pinpoint and can be costly to overhaul the lines.

Article summary: The above is all about how to set up the router optical modem and what are the advantages of the wireless LAN, I hope it will help you. If you want to connect to more related content, please continue to pay attention to Qeeka Home.

First of all, it is necessary to ensure that the network cable is connected to the optical modem, and then when the optical modem is connected to the router, a network cable is required, one end is plugged into the LAN port of the optical modem (the bottom of the empty Zen mouth of the net shirt has a dust logo), the other end is plugged into the WAN port of the router, and the computer at home is connected to any LAN port of the router. After connecting in this way, the computer can also set up a router and then surf the Internet.

At this time, the computer will automatically obtain an IP address, you can right-click the computer in the lower right corner of the computer taskbar, click "Open Network and Sharing Center", find the local connection, click on the details to view the IP address automatically obtained by the computer, and then set the password of the router and so on, you can complete all the operations, the router settings, there will be specific introductions in the manual.

Explanation of terms: Wireless router is a router used for users to surf the Internet and have wireless coverage, and can also be regarded as a converter, which can be connected to a network cable in multiple LAN ports on the back of the router for multiple terminals to use on the Internet, and at the same time, it can also be used by mobile phones and TVs that are inconvenient to plug in network cables through wireless signals.

Enter the area and get the decoration for free**].

With the continuous development of science and technology, every household is basically using wireless networks, and the premise of using the network is to have two devices, optical modem and router, which must be connected before they can be used. So, how to set up the router to connect to the optical modem? What do I need to pay attention to when setting up my router?

Let's take you to find out. The first step is to connect the router to the optical modem, connect the router to power; The second step is to prepare a network cable and an optical modem, and then connect the WAN port of the router and the network port of the optical modem together through the network cable, and the LAN interface of the router is connected to the network cable, and the signal source is available; Step 3: Open the browser, fill in the IP address of the router, press enter to enter the settings interface, set the name and password of the router, and click Save to access the Internet. Precautions for router setting 1, pay attention to the wireless distanceWhen setting up the router, the first thing to pay attention to is the distance, it is best to place it in a high place, but not in the corner of the room, and there can be no obstruction around it, otherwise it will affect its signal source.

2. Pay attention to the influence of interference factorsWhen setting up the router, you should also pay attention to some interference factors around it, and try to avoid interference with other wireless devices. Especially for cordless**, microwave ovens, wireless mice, and other types of devices, it is necessary to stay away. In addition, when using a wireless computer, it is best to delete all the redundant networks and keep only yourself, so that it will not affect the network speed.

3. Pay attention to the compatibility settingsWhen setting up the router, in order to prevent problems with compatibility support such as wap. It's best to update the Wi-Fi drive to the latest version first. In this way, in the process of daily use, the situation of disconnection can be avoided.

Article summary: The above is the content of the whole family shelter about how to set up the router connection optical modem and what needs to be paid attention to in the router settings, I hope it will be helpful to you. If you want to know more about it, please stay tuned to Qeeka Home.

Do the math how much it will cost you to renovate your home

The following describes how to connect a router to an optical modemTools Raw materials: Dell XPS13-9350-3708, Win10, browser.

1. Open the browser, enter the Yinsheng management interface of the router in the address bar, and enter the password.

2. Enter the password to enter the settings page.

3. Click on the left function menu to set up the wizard, select the dynamic IP and click Next.

4. The user sets the SSID and wireless password and clicks Next.

5. Click to complete the automatic restart of Feng Da Lao, and the router is connected to the optical modem and even the imitation grip is connected.