Who has the current situation of single stamping tablet machine at home and abroad, the data is all

Extraction code: 8ruq hcip133 Teacher Tong Courseware Section 1 and 2 USG6000V MPLS-VPN thinking question analysis. MP4 23HCIP - Troubleshooting Case.

mp4 22hcip-firewall (below).mp4

21hcip-firewall (above).mp4 20hcip-vrrp 18hcip-mpls-vpn mp4 17hcip-vrf mp-bgp. mp4

16HCIP-MPLS Fundamentals. mp4 15hcip-rstp 14hcip-switched etrunk mux-vlan port isolation port security. mp4

It has been sent to your mailbox, I hope it will be useful to you.

Hello dear I am glad to serve you: the use characteristics of the single stamping tablet machine: It is a small desktop electric continuous tablet pressing machine, which can also be hand-cranked, and the pressed tablets have average thickness, high gloss, and no need to polish.

TDP-5 single stamping tablet machine can press powdered raw materials into tablets, which can be widely used in pharmaceutical factories, chemical plants, hospitals, scientific research units, laboratory trial production and small batch production. Because the large single stamping tablet machine only has one die, it is called the first leakage of the single stamping tablet machine; The filling depth of the material and the thickness of the tablet can be adjusted. This machine has excellent performance, strong adaptability, easy to use, easy to maintain, small size, light weight, and can also be hand-cranked when there is no electricity.

This machine is only equipped with a die, the filling depth of the material, the thickness of the tablet can be adjusted, can adapt to the requirements of the pharmaceutical industry to suppress various Chinese and Western medicine agents and other industries to suppress a variety of similar products, and is welcomed by the majority of unemployed users. Precautions for use: 1. When pressing the electric tablet, the rotating handle on the handwheel must be pulled down to avoid injuring people during operation.

2. The machine can only run in a certain direction (see the arrow on the handwheel or protective cover), and cannot be reversed to avoid damage to the parts. It is especially important to take care not to be negligent when adjusting the tablet. 3. Regardless of manual tableting or electric compression, the upper punch rod should be in the rising position before starting.

If the upper punch piece is started in the lower position, it will enter the middle mold pressing sheet just after starting, and at this time, because the speed of the machine has not yet risen, the inertia is small, and the situation of top car is easy to occur. (That is, after the upper punch enters the middle mold, it is "dead" due to the resistance of the tablet, so that the machine stops running.) Due to the large load when topping the car, the machine is often damaged or the motor is burned).

4.When there is no power supply, use the hand to press the tablet, and the V-belt should be removed to reduce resistance and wear. But don't remove the large pulley as well, because the large pulley has the effect of saving the effort of the flywheel.

3All models: TDP-5

Maximum tableting pressure: 15kN 50kn

Maximum tablet diameter: 12mm 16mm Shaped 22mmMaximum filling depth: 12mm 12mm

Maximum tablet thickness: 6mm 6mm

Production capacity: 6000 pieces h 6000 pieces h motor:

Dimensions: 670x470x750mm 750x500x700mm

Main machine weight: 90kg 125kg Refueling parts and times Serial number Refueling parts Lubricating oil added Refueling times per shift 1 Spindle hole oil cup (2) Butter 2-3 times 2 Eccentric shell oil cup 1 butter 2-3 times 3 Bridge axle oil cup 1 butter 2-3 times 4 Lifting cam groove (i.e. the groove on the inside of the large gear) Butter Check the surface of the groove every shift to wipe off the dirt, add butter once 5 Fill the groove of the cam Butter Check every shift, refuel as appropriate 6 Gear tooth surface Butter Check every shift, refuel as appropriate 7 Oil hole on the connecting rod Oil 1 time 8 At the swing fulcrum of the lever Oil 1 time 9 Surface of the upper punch rod Oil 2 times 10 Surface of the lifting rod Oil 2 times.

The single tablet press is a small tabletop electric continuous tablet pressing machine, which can also be hand-cranked.

The single stamping tablet machine presses all kinds of granular raw materials into round sheets, which is suitable for laboratory trial production or small batch production of various tablets, sugar tablets, calcium tablets, special-shaped tablets, etc. It is a small desktop electric (manual) continuous tablet pressing machine, which is equipped with a die, and the filling depth of the material and the thickness of the tablet can be adjusted. Various shapes of molds can be provided according to customer requirements.

The single stamping tablet machine is suitable for pressing chewable tablets, traditional Chinese medicine tablets, effervescent tablets, button batteries, western medicine tablets, electronic components, calcium tablets, fertilizer tablets, oral lozenges, mothballs (sanitary balls), spirulina tablets, milk tablets, candy tablets, disinfection tablets, aromatic tablets, flavor blocks, catalysts, pesticide tablets, metallurgical powder ceramic granules, etc.

This function can press powdered raw materials into tablets, and the products are widely used in pharmaceutical factories, chemical plants, hospitals, scientific research units, laboratory trial production and small batch car grinding production. Excellent performance, strong adaptability, easy to use, easy to maintain, small size, light weight, this machine is only equipped with a die, the filling depth of the material, the thickness of the tablet can be adjusted, can adapt to the requirements of the pharmaceutical industry to suppress various Chinese and Western medicine preparations and other industries to suppress a variety of similar production and sail products, welcomed by the majority of users in various industries.