How to coat a car wash, what is a coatings car wash

When the vehicle to be washed enters the parking space, the car is flushed first, one is to cool the car, and the other is to wash off the dirt such as mud and sand on the body.

Dilute the no-wipe car wash liquid according to the dilution ratio on the instructions for use, put it into a stainless steel foam tank or high-pressure spraying can, spray it out in the form of spray, and spray it evenly on the surface of the car. Tip: Start spraying from the cab position, go around the car, and finally spray the engine hood.

After the car wash liquid is evenly sprayed on the surface of the car, (no need to wait) start to rinse with high-pressure water pressure along the position where the car wash liquid is sprayed, (high-pressure water gun requirements: pressure above 8MPa, water output 15 20l min, water surface is fan-shaped 15 ° 25 ° angle, speed about 1440 rpm), the whole washing process does not need to be wiped until the car surface is washed clean.

After the body surface is rinsed, keep the surface of the car moist and start coating

1. Dilute the Dongdi water coating film in the ratio of 1:55 60 and use a manual watering can (the watering can used for watering flowers is sufficient);

2. Spray the water coating diluent evenly on the body surface, car glass, and wheel hub (suggestion: carry out sub-regional operation on the entire car body, wipe it with a clean sponge while spraying, so that the water coating diluent is better and more evenly distributed on the body surface) After spraying, rinse after wiping, so that the coating effect is better! Coating Effect:

The lotus leaf effect, i.e. the hydrophobic effect, is particularly noticeable.

3. After the coating is completed, the car will be exposed to the sun for about 30 minutes, and the coating effect will last for about 30 days.

4. The coating car wash is completed.

Apply a layer of brightener while washing the car. It is a flickering way of the store, in fact, it is a car after washing the car to appear bright, the effect is very low, it can only have an effect at the time, I am using it, but I didn't say it, it still depends on the quality, after a long time, the customer will know your service attitude and service quality, and you want word of mouth.

What is a Coated Car Wash? It is a combination of the simplest car wash and the best car beauty method - coating, which completes the beauty maintenance of the vehicle while improving the car wash function. That is, immediately after washing the car, the car paint surface Changkai is coated with a layer of glass fiber coating, which is convenient and fast, and the vehicle can be thoroughly protected in just a few minutes, so as to prevent paint oxidation, acid rain corrosion, ultraviolet rays and improve the hardness of the paint surface by 3 times.

It is a new car wash concept and paint care method. What is the principle of coating car wash? When washing the car, it is like spraying car wash liquid, spraying a special quick coating liquid (crystal coat), so that the dirt on the surface of the car paint (exhaust gas floating granular substances and oil, grease, sand and soil, etc.) float up from the surface of the body, and at the same time, the glass fiber molecules produced by the quick coating liquid through the chemical reaction are combined into a solid surface coating on the surface of the car paint through the gaps floating up from the car surface, so as to achieve the effect of car washing and coating at the same time, so as to achieve the goal of cleaning and protecting the car paint.

Why should you choose this film car wash? 1. Coated car wash is a real non-scratch car wash; 2. Coated car wash can make the vehicle brighter and brighter the more it is washed, increasing the added value of car washing; 3. The products used in the coating car wash have special cleaning ingredients, which can professionally clean the car paint; 4. Coating car washing can complete the car paint coating at the same time as the car wash, that is, at the same time as the car wash, the car body is coated with a layer of glass fiber protective layer, and the car beauty operation is completed at the same time when the car is washed. In short, the coated car wash is definitely better than the ordinary car wash, the ordinary general wash, the foam is OK, there is no protective film, just clean it.

Car services are provided to the majority of car owners.

Coating beauty car wash is the combination of the simplest car wash and the best car beauty method - coating into the shooting, which improves the function of car wash and completes the beauty maintenance of the vehicle. That is, immediately after washing the car, the surface of the car paint is coated with a layer of glass fiber coating, which is convenient and fast, and the vehicle can be completely protected in just a few minutes, so as to prevent paint oxidation, acid rain corrosion, ultraviolet rays and improve the hardness of the paint surface by 3 times. It is a new car wash concept and paint care method.

Coated beauty car wash is the product of the latest car cleaning technology and market demand, and it is a revolution in the car cleaning market; Coated beauty car wash is a real non-scratch car wash, which can make the vehicle brighter and brighter, completely subvert the existing car wash concept, and truly make car wash an indispensable part of car maintenance; Coating beauty wash Kaiche is the popularization of the existing high-end glass fiber coating, so that the car paint coating has become a daily steam, coating beauty car wash that has the maintenance effect of the car, but there is no damage to the car paint, will quickly become the replacement of the existing car wax market.

When light enters different transmitting substances (e.g. air into glass), about 5% is reflected, and there are many lenses and refractors in the optical sight, which together can cause a loss of 30% to 40% of the incident light. Modern optical lenses are usually coated with a single or multi-layer anti-reflection coating of magnesium fluoride, a single-layer anti-reflection coating can reduce the reflection to, and a multi-layer anti-reflection coating can reduce the reflection to, so if the entire scope is properly coated, the light penetration rate can reach 95%. Lenses coated with a single layer of anti-reflection coating are usually blue-purple or red, while lenses coated with multiple layers of anti-reflection coating are pale green or dark purple.

When light enters different transmitting substances (e.g. air into glass), about 5% is reflected, and there are many lenses and refractors in the optical sight, which together can cause a loss of 30% to 40% of the incident light. Modern optical lenses are usually coated with a single or multi-layer anti-reflection coating of magnesium fluoride, a single-layer anti-reflection coating can reduce the reflection to, and a multi-layer anti-reflection coating can reduce the reflection to, so if the entire scope is properly coated, the light penetration rate can reach 95%. Lenses coated with a single layer of anti-reflection coating are usually blue-purple or red, while lenses coated with multiple layers of anti-reflection coating are pale green or dark purple [1].

1. Automobile coating has anti-oxidation and anti-aging effects: automobile coating has the effect of anti-oxidation and anti-aging, and a hard inorganic (silica glass crystal) coating layer is formed on the surface of the car paint after construction, which is closely combined with the car paint to improve the hardness and smoothness of the paint surface, completely isolate the paint surface from the air, and never fall off without external force factors. 2. Super water repellency:

The hard non-organic (glass crystal) film surface has super water repellent properties after fluorine treatment, so that the water shrinks into water droplets when it falls on the car body, and effectively prevents the formation of scale. @2019

Car Coating Steps:

1. Paint decontamination, polishing, upper coating agent, lower coating agent; Paint decontamination, scratch repair, polishing, upper coating, lower coating;

2. Automobile paint coating is to coat a thin film on the automobile paint, the purpose is to protect the gloss of the automobile paint from attenuation, and at the same time make the paint surface physically obtain a protective film, so as to achieve the purpose of protecting the paint surface;

3. Macromolecular polymers, simply put, are molecules connected hand in hand, because of their strong film-forming, they can form a film in the real sense, so most of the automotive coating products on the market are macromolecular polymer chemical products;

4. Usually the hardness of the paint surface when the car leaves the factory is 3 to 4h, and the hardness of the paint surface after the paint crystal coating can effectively reach 9h, so the painted surface after coating can effectively prevent the generation of some small scratches. However, some scratches occur because the car film itself is hard, and when friction occurs, the friction residue of the other party is rubbed on the paint surface;

5. Although this situation will not cause damage to the car film, it will also leave traces. As usual, small scratches on the painted paint surface are also very easy to deal with, as long as they are effectively removed after simple mirror reduction, the luster can be restored, and the paint surface itself will not be worn.

1. Clean the car body, use clay to clean the oxide layer on the paint, and the stubborn stains.

2. Paste the plastic part of the body with 3M adhesive tape.

3. Polishing the paint part, reducing the dust, and removing the scratches on the surface of the paint.

4. Clean the abrasive powder left by the body after polishing and clean the wheels.

5. Remove the oil film from the front windshield and coat the glass hydroplaning coating.

6. After cleaning the body, dehydrate the whole car and blow dry.

7. After a period of curing and reacting with the moisture in the air, a layer of vitreous protective film will be formed on the paint to reduce fine scratches.

8. Use a dry towel to wipe the film liquid on the paint evenly.

9. Apply a water repellent accelerator.

10. End of coating.

Automotive electroplating film placement method:

1. Paint treatment, due to the extremely high reflectivity of the electroplating mirror, the paint dust is easy to appear; Before construction, it is very necessary to deeply clean the construction environment and vehicles, and it is recommended that before construction, dust reduction and use 3M car washing mud to clean the surface of the car paint, and it is recommended to do full polishing treatment;

2. For film construction, scrape and paste the scraper 1 4-1 3 each time, and pay attention to the force and angle, but it is necessary to avoid scratching the corner of the scraper against the film; The brightness of the mirror is high, and it is easier to have scraper marks after construction, and it is necessary to control the strength and angle of the scraper as much as possible, and after 7-15 days after the construction is completed, the scratches are reduced or lighter;

3. Use the defoamer, spray it on the non-woven fabric, wipe the paint surface with heat soaking (it can be wiped horizontally and vertically), do not apply the defoamer at the grooves and corners, and pay attention to the need to complete the large-area film construction in a short time after the defoamer is dried to avoid residual water droplets and foam; If the splicing construction, the splicing seam should be at the water chestnut of the sheet metal surface as far as possible (refer to the upper pressure and the outer layer);

4. After the construction is completed, wipe it with new dust-free paper (or a new fiber orange towel) after construction, do not place things and touch the film surface with your hands during and after construction. If you want to use it for a long time, it is recommended that the scratches of the transparent film be repaired automatically, which can effectively improve the service life of the electroplating film and generally extend it by more than 3 years.

Millions of car purchase subsidies.

Vehicle coating can effectively protect automobile paint from wear, so what are the processes of automotive coating when coating the car?

1. Before the car coating, the surface of the car body needs to be cleaned first, otherwise the stains on the body will affect the subsequent coating treatment.

2. After cleaning the car body, wait until the surface of the car body is completely dry, and then cover the position on the body that does not need to be coated, and then you can coat the car body.

3. During the coating process, it is best to use professional tools to smear the coating material, which can ensure that the vehicle coating is more uniform.

4. Then wait until the coating is for a period of time, you can wipe off the coating agent on the body, and finally use a cotton towel to clean the body, and the vehicle coating is basically completed.

The above is the general process of automobile coating, but in order to ensure that the best effect can be achieved after car coating, it is best for the owner not to clean the vehicle for a few days after coating, otherwise, it is easy to cause damage to the vehicle film.

The process of car paint coating is different for each product, so it is best to consult the brand or store!