The air energy temperature can t go up, what s the matter?

The installation location is a problem, the air energy water heater needs to be installed in a ventilated place, preferably on the balcony. Solution: Adjust the installation position or install a fan for ventilation.

The refrigerant dose is low, and too low the refrigerant will also cause the temperature to be too low. Solution: Add refrigerant, generally R134A environmentally friendly refrigerant is preferred.

The capacity is on the low side, and the small capacity will cause the water consumption to far exceed the capacity, resulting in a slow heating rate. Solution: Contact the manufacturer to replace the model or increase the host and water tank (split), generally 150L for 3 people, 200L for 4 people, if the water consumption is large and the bathroom is more, you can add 50L more

The heat exchange fins are dirty, and the heat exchange fins are dirty, resulting in slow heating and slow rise in water temperature. Solution: Clean the heat exchange fins regularly and keep the surroundings of the machine clean and tidy.

Scale factor, the water quality is hard in areas will appear scale phenomenon, scale also affects the water temperature and temperature. Solution: Add water purification equipment or clean the heat exchanger regularly.

This can be said to be very normal, the air can be heated to a maximum of 62 degrees Celsius by hot water (experimental data in the laboratory summer). Secondly, the water temperature of air energy is generally between 50-60 degrees, which is related to the local air temperature, the quality of the compressor and so on. If the general area, the general situation can reach 56 degrees is normal.

Air energy water heaters.

The temperature cannot be increased during use, so you need to pay attention to the following points. 1. The installation position of the water heater has poor ventilation effect, which affects and increases the use and causes the temperature to not go up; 2. Lack of refrigerant.

Heat is not well guaranteed; 3. The heat exchange fin has not been cleaned for a long time, and the heating is very slow, and the water temperature rises very slowly. The water heater has not been cleaned for a long time, and a large amount of scale appears to affect the heating effect. The solutions for temperature regulation are:

1. It is necessary to install the air energy water heater in a position with good ventilation conditions to ensure that it can operate and use normally, and it is generally better to install it on the balcony. 2. After a long period of use, there is a leakage, resulting in the lack of refrigerant in the water heater, which can not ensure heating well, so it is necessary to add refrigerant in time, but it is necessary to pay attention to the scientific and correct addition. 3. The heat exchange fin is also very important, the water heater will be heated very slowly when it is full of dust, and the water temperature is always difficult to go up, so it is necessary to clean the heat exchange fin regularly, and replace it in time if necessary, and ensure that the equipment is in a very clean state all around.

4. The problem of scale has a lot to do with the quality of tap water, you can choose to clean the water heater regularly to reduce the existence of scale, and also ensure that it can be heated normally and can be used more smoothly.

Dear Kiss I'm glad to answer for you, my answer is as follows:|The reasons for the failure of the air energy temperature are as follows: 1. The leakage or shortage of refrigerant will cause the air energy water heater to carry insufficient heat carrying capacity, reduce the heating efficiency, or even fail to heat.

If this is the reason for the air energy water heater, the water temperature can not go up, the user needs to notify the after-sales personnel to come to the door for maintenance, supplement the refrigerant, and ensure the normal use of the hot air water heater, 2, the insulation effect is poor, and the poor quality of the insulation layer of the air energy water heater will lead to the rapid loss of heat in the water tank. A good insulation layer should be made of imported foaming materials, a foaming, foaming uniformly, the thickness of the insulation layer should be at least In addition, the water tank inlet and outlet valve port is not tightly sealed, or the insulation work in the hidden place is not in place, which will accelerate the heat loss, so that the user feels that the air can water heater water temperature can not go up.

The reasons for the failure of the air energy water heater are as follows: 1. The installation location problem, the air energy water heater needs to be installed in a ventilated place, and it is best to install it on the balcony. Workaround:

It is recommended to adjust the installation position, the old stove or install a fan for ventilation. 2. The refrigeration dose is small, and the refrigerant is too low, which will also lead to too low temperature. 3. The capacity is small, and the small capacity will cause the water consumption to far exceed the capacity, resulting in slow heating speed.

Solution: Contact the manufacturer to replace the model or increase the host and water tank (split type), generally 150L for 3 people, 200L for 4 people, if the water consumption is large and the bathroom is more, you can increase the heat exchange fins dirty, and the heat exchange fins are dirty resulting in slow heating and slow rise in the water temperature of the nucleus. Workaround:

Clean the heat exchanger fins regularly and keep the area around the machine clean and tidy. 5. Scale factor, scale will appear in areas with hard water quality, and scale will also affect the temperature of the water service. Workaround: