How to dismantle the car armrest box, how to dismantle the Lexus armrest box

The first step is to take Audi cars.

For example, open the armrest box first, as shown in the following figure:

The second step is to remove the screws in the armrest box, as shown in the figure below

The third step, then hang the car gear to the n gear, hold the gear handle and lift it up forcefully, and break free from the fixed buckle of the gear knob, as shown in the following figure:

Fourth, use a pry board to pry open the joint between the storage box panel and the armrest box, as shown in the figure below

The fifth step, the buckles on both sides of the car armrest box are pried open, as shown in the following figure:

Sixth, lift the armrest box upwards, as shown in the following figure:

The seventh step and finally the armrest box of the Audi car is removed, as shown in the figure below

First of all, the cover plate of the gear handle should be removed, the screw of the gear handle should be removed, the gear handle should be taken out, the rubber at the bottom should be pried open, the screws should be removed, and the ashtray could be taken out after the cover plate of the ashtray was promoted, and finally the operation panel was pulled up to complete the disassembly of the handrail box.

The armrest box is a car interior accessory located between the seats, which is originally intended to prevent the driver's arm from being driven so that the arm has a force support without stiffness. With the development of technology, most of the armrest boxes now have a storage function at the same time, which can prevent water cups or other small items, which is relatively close to the driver, and is also convenient for the driver to reach when driving. When disassembling the armrest box, first open the armrest box, remove the cotton cover, and then remove the internal screws, then keep the vehicle in N gear, forcefully lift the gear handle, and then pry open the combination of the panel and the handrail of the storage box, and pry the buckles of the two cars are pried open, you can directly lift the armrest box upwards, and pay attention to placing small screws and parts while disassembling.

The part of the air outlet that needs to be removed is buckled. If you remove it, you can see that the two fixing screws can be removed by unscrewing.

A car armrest box is a car accessory that is installed between two seats and is subordinate to the interior system of the car. Its humanized design is intended to enable the driver of the car to place his arm when driving for a long time, so that the arm can be effectively rested without soreness and stiffness.

First dismantle the ashtray behind the armrest box and pry it with a hard-dotted card! Then it's easy to dismantle!

Hello, dear ask users, hello! I, Lu Jian, is your special question for Xiao Ni, your question has been received, and I am urgently sorting out the answer for you. Please don't be in a hurry, typing is slow, I will reply to you in about 3-5 minutes, please wait a while!

Hello dear! I'm glad to answer for you, here for you to inquire: the disassembly method of the overbearing handrail box is as follows:

1. First of all, open the armrest box and uncover the cotton cover inside; 2. Use tools to disassemble the two screws and place the fixing screws; 3. Hang the gear to the n gear, and then hold the gear handle and lift it up forcefully to break free from the fixed buckle of the gear handle; 4. Use a plastic screwdriver to pry the place where the storage box panel and the armrest box are combined, and pry the left side first; 5. Then pry the buckle on the right side. After priing up the ends, lift them up and break free of the buckle. Hope it can help you and have a happy life!

The landlord, you said that this suggestion is better to go to the store, it is better to handicraft and it doesn't cost much.

The root of the hand box side two cover plate and the back cover plate removed, buckle, directly pry on the line, after removing a 13 screw cap, remove on the line, directly can be taken down.

Hello, are your handrails still there, I want to acquire.

Real car decoration car products Taoqi shop has a high-end armrest box.

The removal method of the Baojun 510 armrest box cover is as follows.

Open the armrest box and remove the internal screws, a 10-gauge screwdriver is required here.

Handbrake. Pull to the highest height and pry the plastic cover on the side of the handbrake open. Remove the cigarette lighter.

Cover. This cover is not fastened with screws, you can use the gap as a breakthrough, after the cover is warped, separate the three buckle plugs, and take off the cigarette lighter cover.

Remove the set screws, there will be two set screws under the cigarette lighter cover, and a 10-screw wire cutter will be used. Then you can take down the armrest box to fix the buckle. Put the knob in nth gear.

Lift it up, and the gear handle will be separated from the gear core. A plastic driver is then used to remove the handlebar cover.

The method of installing the car armrest box is as follows:

The armrest box is generally composed of 3 parts: the bottom cavity family seat, the middle connection box, and the box composition, the installation method of the armrest box is quite simple, so simple that you only need to align the car body and put it down directly, and then clamp it on.

However, the more correct installation method is to sit in the rear row of installation, before the installation of one of the front and co-pilot seats to the front, after the installation and then reset it, the need to pay attention to the seat belt when resetting.

Do not touch the buckle of the handrail box.

Nowadays, cars have become a popular tool for our daily travel, but some problems will inevitably arise during use, such as: how to disassemble the car's glove box. Then I will introduce it to you below, I hope you can help.

Depending on the model, a professional removal tool is required to disassemble the glove box.

To start opening the car's storage compartment, you need to pull the piston buffer card on the right side of the storage compartment and turn the fixed button on the right side of the storage compartment counterclockwise. There are knobs on the upper and lower sides of the storage box, and the fixed knobs on the upper and lower sides need to be removed. Once removed, the storage box can be opened to the maximum.

When the storage box is opened, you can see the fixed pin between the storage box and the base. You can use a buckle screwdriver to remove the retaining pin on the right side of the storage bin. Again, you need to remove the pin on the left side. Once the latch is removed, the storage box can be removed.

Compared to the same period last year, the storage boxes in the car are not particularly large and can be used to store some vital documents. If it is a prominent object, it cannot be placed in the storage box.

In addition to the storage box, the car's **armrest box can also store things. A car armrest box is a car attachment that is installed between two seats. With the continuous development of automobile manufacturing technology, the armrest box has more useful functions, such as storing small items such as drinks and drinking glasses, so that the driver can easily access these items when they need them.

As follows:

1. Open the armrest box, there is a cover plate inside, pry open with screws, use a tool to unscrew and remove.

2. The car armrest box is an automobile accessory installed in the middle of the two seats, which belongs to the automotive interior system.

3. Humanized design, so that the driver of the dust-selling car can place his arm when driving for a long time, so that the arm can effectively rest without soreness and stiffness.

It is best to go to a 4S shop or a professional repair shop and ask a professional repairer to disassemble it. The car Fuzhong Douzen hand box is an auto part that is installed between two seats, and the pin belongs to the car interior system. Its ergonomic design is designed so that the driver of the car can lower his arm during a long drive, so that he can effectively rest his arm without feeling soreness and stiffness.

XF as Jaguar.

The mid-size and large-sized luxury cars are divided into Standard, Touring and XRFR Performance Editions. In terms of design, the Jaguar XF leans more towards the XK's car manufacturing philosophy, which is full of modern touches: an atmospheric front face, smooth body lines, and grille.

A leopard is embedded in the middle.

logo, which highlights the car's extraordinary characteristic momentum.

First of all, the cover plate of the gear handle should be removed, the screws of the gear handle should be removed, and then the rubber at the bottom should be pried open, the screws should be removed, and the ashtray can be taken out after the cover plate of the ashtray is pushed, and finally the operation panel is pulled out to complete the disassembly of the armrest box.

The armrest box is a car interior accessory located between the seats, which is originally intended to prevent the driver from getting sick while driving, so that the arm gear has a force support instead of stiffness. With the development of technology, most of the current armrest boxes have a storage function at the same time, which can prevent the water mold morning cup or other small items, this position is relatively close to the driver, and it is also convenient for the driver to take it at hand while driving. When disassembling the armrest box, first open the armrest box, remove the cotton cover, and then remove the internal screws, then keep the vehicle in N gear, forcefully lift the gear handle, and then pry open the combination of the panel and the handrail of the storage box, and pry the buckles of the two cars are pried open, you can directly lift the armrest box upwards, and pay attention to placing small screws and parts while disassembling.

Different brands of cars have different armrest box settings. Take Beijing Hyundai ix25 as an example to demonstrate how to disassemble the armrest box. Step 1:

Open the armrest box and remove the internal screws. A 10-gauge screwdriver is required here. Step 2:

Pull the handbrake to the highest position of the 3360 and pry open the plastic cover on the side of the handbrake. Step 3: Remove the cigarette lighter cover.

How to disassemble the armrest box of a car Different brands of cars have different handrail box settings. Take Beijing Hyundai ix25 as an example to demonstrate how to disassemble the armrest box.

Step 1: Open the armrest box and remove the internal screws. A 10-gauge screwdriver is required here.

Step 2: Pull the handbrake to the highest position of the 3360 and pry open the plastic cover on the side of the handbrake.

Step 3: Remove the cigarette lighter cover. This cover is not fastened with screws, and the gap can be used as a breakthrough. After tilting the lid upwards, separate the three snap plugs and remove the cigarette lighter cover.

Step 4: 3360 Remove the set screws. There are two set screws underneath the cigarette lighter cover and require a 10-gauge screwdriver. The armrest box retaining buckle can then be removed.

Step 5: 3360 Put the gear knob in n gear and lift it up, and the gear handle will be separated from the block core. Then use a plastic screwdriver to remove the cover of the gear handle.

Step 6: 3360 Remove the self-tapping screws of the armrest box. The screws are under the cover plate of the gear handle. At this time, hold the back half and lift it up to get to the armrest box.

Finally, a few additional notes:1. Take away the removed screws and buckles, and do not lose them; 2.

When disassembling, pay attention to protecting the empty control panel and central control components; 3.During installation, pay attention to check whether the mat at the carpet is stuck. How to disassemble the armrest box for the co-pilot of the car Different brands of cars have different armrest box settings.

Take Beijing Hyundai ix25 as an example to demonstrate how to disassemble the armrest box.

Step 1: Open the armrest box and remove the internal screws. A 10-gauge screwdriver is required here.

Step 2: Pull the handbrake to the highest position of the 3360 and pry open the plastic cover on the side of the handbrake.

Step 3: Remove the cigarette lighter cover. This cover is not fastened with screws, and the gap can be used as a breakthrough. After tilting the lid upwards, separate the three snap plugs and remove the cigarette lighter cover.

Step 4: 3360 Remove the set screws. There are two set screws underneath the cigarette lighter cover and require a 10-gauge screwdriver. The armrest box retaining buckle can then be removed.

Step 5: 3360 Put the gear knob in n gear and lift it up, and the gear handle will be separated from the block core. Then use a plastic screwdriver to remove the cover of the gear handle.

Step 6: 3360 Remove the self-tapping screws of the armrest box. The screws are under the cover plate of the gear handle. At this time, hold the back half and lift it up to get to the armrest box.

Finally, a few additional notes:1. Take away the removed screws and buckles, and do not lose them; 2.

When disassembling, pay attention to protecting the empty control panel and central control components; 3.During installation, pay attention to check whether the mat at the carpet is stuck. How to disassemble the car armrest box 2019

Different brands of cars have different armrest box settings. Here is a Beijing Hyundai ix25 ( Check transaction price |Detailed explanation of the model) as an example to demonstrate how to disassemble the armrest box.

Step 1: Open the armrest box and remove the internal screws. A 10-gauge screwdriver is required here.

Step 2: Pull the handbrake to its highest height and pry open the plastic cover on one side of the handbrake.

Step 3: Remove the lid of the cigarette lighter. This cover is not fastened with screws, and the gap can be used as a breakthrough. Once the cover is tilted upwards, detach the three snap plugs and remove the cigarette lighter cover.

Step 4: Remove the set screws. There are two set screws under the lid of the cigarette lighter, which requires a 10-gauge screwdriver. Then you can remove the armrest box fastener.

Step 5: Put the gear handle in the n position, lift it, and the gear handle will be separated from the gear core. Then use a plastic screwdriver to remove the cover of the gear lever.

Step 6: Remove the self-tapping screws of the armrest box, and the screws are under the cover plate of the gear handle. At this point, hold the back half, lift it up, and remove the armrest box.

Finally, what should be paid attention to when replenishing parts:1. Remove the screws and buckles, and be sure not to lose them; 2.When disassembling, care should be taken to ensure that the air adjustment panel and central control components are empty; 3.During installation, pay attention to check whether the mat at the carpet is stuck.

Well, that's the end of my introduction. Do you know how to disassemble the armrest box? Hope it helps. If necessary, we are here waiting for your visit. @2019