There is an overclocking on the desktop, how to eliminate

1. First on your own computer desktop.

and tap on the computer as shown in the image below.

2. Then click to open the control panel of the upper beam differential tremor.

This is shown in the figure below.

3. Then find and click Display, as shown in the figure below.

4. Under the display page, find and click Adjust Resolution, as shown in the figure below.

5. Then click on Advanced Settings, and click on Monitor on the Advanced Settings page, as shown in the figure below.

6. Finally, select Qingming to choose a higher frequency refresh rate, and click OK.

You guys know how to cancel the monitor overclocking.

Here's what I brought about how to cancel my computer monitor when it was overclocked, welcome to read!

How do I cancel my computer monitor overclocking?

Causes of monitor overclocking:

Manually setting the frequency yourself leads to overclocking.

There is also an incompatible driver that causes overclocking.

Caused by low display configuration.

In the case of overclocking caused by manually setting the monitor frequency ourselves, if this is the case, the system can recover by itself for a period of time, because there is a reset function, if you do not do anything in 15 seconds, it will automatically restore the state before you set it.

Another situation is caused by the low configuration of the display,For example, we have replaced the host,The display is still the old monitor,The host configuration is connected to the monitor at home and can't be used,The display is overclocked,There is no problem with this host,There is no problem with the display,It's just that the display does not support the minimum required frequency of the computer host,It can only be solved by replacing the display。

The last one is caused by driver incompatibility, this situation mainly occurs in the computer to update the graphics card, or the host redoes the system, after starting the computer to display overclocking, this may be caused by the imperfect production of the system image file, let's talk about the solution:

First, start the computer and press F8 to enter safe mode.

Once in safe mode, right-click on My Computer and select Device Manager.

Then pull down the scroll bar to find the display adapter.

Different computers have different driver models, then right-click to select your graphics card driver.

Click Uninstall, if you have two graphics drivers under the monitor adapter, then you have dual graphics drivers, if you are not sure which one to use, then uninstall both.

Restart the computer after uninstalling.,You can definitely enter the system.,But the driver is deleted.,You need to reinstall the system driver.,This can be used with the driver wizard.。

It's relatively simple to install.

1.What to do if your computer monitor is overclocked.

2.The computer monitor shows what's going on with overclocking.

3.XP system computer monitor overclocked black screen.

What to do 4How to adjust the computer monitor if it is overclocked.

5.What to do if your computer monitor shows overclocking.

6.What to do if your win7 monitor is overclocked.

Summary. Computer overclocking recovery method 1.

First, uninstall the graphics card driver, reinstall the graphics card driver, and set the graphics card resolution from low to high. Restart the computer and press F8 during boot to enter the system security mode. Right-click on My Computer - Device Manager - Display Devices - Right-click on the graphics driver - Uninstall.

Then restart the computer, and after entering the desktop, the system will detect that the graphics driver is not installed, and a prompt will pop up to find new hardware. **Install the Driver Wizard and run it. The driver wizard will automatically detect the graphics card model and recommend a suitable driver, click "Install".

Find a monitor that supports high resolution, connect it, turn down the screen resolution, and save it. Replace the original monitor, debug it to a suitable one, and then save it to exit.

What to do if the monitor shows overclocking.

The first method of computer overclocking recovery is to uninstall the graphics card driver, reinstall the graphics card driver, and set the graphics card resolution from low to high. Restart the computer and press F8 during boot to enter the system security mode. Right-click on My Computer - Device Manager - Display Devices - Right-click on the graphics driver - Uninstall.

Then restart the computer, and after entering the desktop, the system will detect that the graphics driver is not installed, and a prompt will pop up to find new hardware. **Install the Driver Wizard and run it. The driver wizard will automatically detect the graphics card model and recommend a suitable driver, click "Install".

Find a monitor that supports high resolution, connect it, turn down the screen resolution, and save it. Replace the original monitor, debug it to a suitable one, and then save it to exit.

Computer overclocking recovery method two manually set the monitor frequency caused by overclocking, if this is the case, the system can recover by itself in a period of time, because there is a restore function, if there is no operation in 15 seconds, it will automatically restore the state before you set. Another situation is caused by the low configuration of the display,For example, the host has been replaced,The display is still the old monitor,The host configuration is connected to the monitor at home and can't be used,The display is overclocked,There is no problem with this host,There is no problem with the display,It's just that the display does not support the minimum required frequency of the computer host,It can only be solved by replacing the display。

Computer overclocking recovery method 3 to restore the BIOS settings, boot the computer repeatedly press the delete button to enter the motherboard BIOS interface, please refer to the motherboard manual, set back to the default state. Due to the large difference between the BIOS of each motherboard, the old English BIOS interface and the current graphical BIOS interface are not given here. CMOS discharge, open the computer case, find the round battery on the motherboard, and remove it.

Put it back after 5 minutes, at which point the BIOS settings are emptied and go back to default. The CPU voltage you overclocked has been cleared. The PC will run in a normal state.

Here's how:

1. If the computer display is overclocked, you only need to turn it off, and click the [Start] icon button in the lower left corner of the computer. Then click Control Panel.

2. In the control panel interface, find the [Adjust Screen Resolution] option under [Appearance and Personalization] and click it.

3. Next, click the [Advanced Settings] function in the lower right corner of the screen resolution setting interface.

4. Then click [Monitor] in the top function in the advanced settings interface of the monitor.

6. Next, you can re-select the refresh rate of the screen, so that everyone is trying to see if the problem is solved. Basically, this method can solve this problem.

It should be possible to modify the settings in the BIOS or CMOS settings of the boot to prevent the CPU from overclocking, you are talking about CPU overclocking.

Causes of monitor overclocking: overclocking caused by manually setting the frequency by yourself, overclocking caused by incompatible drives, and low display configuration. Workaround:

1. In the case of overclocking caused by manually setting the display frequency by yourself, if this is the case, the system can recover by itself within a period of time, because there is a restore function, if there is no operation in 15 seconds, it will automatically restore the state before setting.

1.The situation caused by the low configuration of the monitor is only that the monitor does not support the minimum required frequency of the computer host, and can only be solved by replacing the display. Second, the driver incompatibility caused by this situation mainly occurs in the computer to update the graphics card, or the host redo the system, after starting the computer to display overclocking, this may be caused by the imperfect production of the system image file, the solution is as follows:

First, start the computer and press F8 to enter safe mode.

After entering the safe mode, right-click to open "My Computer", select Device Manager, and then pull down the scroll bar to find the display adapter, different computers have different driver models.

3.Then right-click and select the graphics card driver and click Uninstall, if there are two graphics card drivers under the display adapter, then it is a dual graphics card driver, if you are not sure which one is used, then uninstall both.

After uninstalling, restart the computer and reinstall the system driver.