Which projects on the construction site need to do a good job of fire prevention measures.

Electric welding, outer frame, square timber and square timber stacking area, temporary electricity.

Fire safety measures.

1) Establish a safety and fire prevention fire brigade headed by the person in charge of security;

2) The construction site is clearly divided into fire operation areas, flammable and combustible material yards, warehouses, flammable waste concentration stations and living areas;

3) The road at the construction site must be unobstructed to ensure that the fire truck is unimpeded in case of disaster;

4) The construction site should be equipped with sufficient fire-fighting equipment, and designated personnel should be designated for maintenance, management, and regular updating to ensure that it is complete and easy to use;

5) Smoking is strictly prohibited in the fire-free area of the construction site.

Second, the key points of fire prevention of on-site electrical equipment.

1. All kinds of electrical equipment and lines are not allowed to be overloaded, and the joints must be connected firmly and firmly to avoid overheating or ignition and short circuit. Repair problems immediately if they are found;

2. Flammable, explosive and combustible gases shall not be stored in the site warehouse, and the lighting line shall be protected by pipes, and explosion-proof lamps and lanterns shall be used;

3. Wires through the wall and wires close to flammable materials should be protected by pipes, lamps and flammable materials should generally maintain a distance of 30cm, and high-power bulbs should increase the spacing. Iodine-tungsten lamps are not allowed to be used in the shed;

4. Temporary buildings are not allowed to be erected under the high-voltage line, and combustible materials are not allowed to be stacked.

<> technical measures for safety and fire prevention on the construction project site are very important, and the formulation of measures is to better ensure safety, especially fire prevention is the key. Zhongda Consulting will explain to you the technical measures for safety and fire prevention at the construction project site.

1.Electrical fire protection:

Reasonable configuration, setting, replacement of various protective appliances, reliable protection of circuit and equipment overload, loss of voltage, leakage, short circuit faults.

Flammable, explosive and strongly corrosive media are not allowed to be stacked around electrical installations and lines, and ignition sources are not allowed to be used casually.

In places where electrical installations are relatively concentrated, such as substations, power distribution rooms, generator rooms, etc., corresponding fire extinguishing equipment is equipped and fireworks are prohibited.

Strengthen the interphase and interpolar insulation of electrical equipment to prevent flickering.

Set up reasonable lightning protection and lightning protection measures.

It is strictly forbidden to stop and transmit power with load.

Explosion-proof electrical equipment is selected in flammable and explosive places.

2.Fire prevention at the construction site.

Divide the key fire prevention areas, assign special personnel to be responsible for key parts, and configure no less than two foam fire extinguishers, cubic sand pools, 1 cubic water pool and fire bucket milling in the woodworking shed. Fire-fighting equipment is not allowed to be diverted for other purposes.

The sawdust produced every day in the woodworking shed is planed and transported by special personnel to keep it clean.

Hang signs prohibiting fireworks and fire prevention responsibility signs.

The wood drying furnace is built in the designated location, away from the fire source, and a special person is arranged to be on duty and supervised.

There is a smoking room on site, and it is not allowed to smoke in the on-site fire prevention area.

3.Warehouse fire prevention.

No one is allowed to smoke on the bed in the dormitory, and there is a special person in the dormitory who is responsible for supervising fire prevention.

Lighting fixtures greater than 60W shall not be installed in the dormitory, and it is not allowed to use electric stoves for cooking, and tungsten lamps shall not be used for lighting.

Use electric mattresses and electric fans with special electricians to install sockets.

4.Electrical welding operations.

Safety and fire prevention measures should be formulated at the cutting and welding operation site, equipped with fire-fighting equipment, supervised by special personnel, and strictly in accordance with the approval procedures for fire.

If there are flammable materials under or around the work site, clean them up first or take isolation measures before working.

First, the formwork yard fire prevention high tung hunger knows.

2. Warehouse security and fire safety management measures.

3. Fire prevention measures at the construction site.

Fourth, the fire ban area division and approval regulations.

5. Measures for the allocation of fire extinguishing equipment.

Sixth, welding and cutting operations "ten do not burn" regulations.

Construction site: The construction site refers to the construction site for the construction of industrial and civil projects, civil engineering, equipment installation, pipeline laying and other construction activities, and the approved occupation of the construction site and the place where human beings carry out safe production, civilized work and construction, including all areas on land, sea and air that can carry out the construction work. The project manager is fully responsible for the on-site management of the construction process, and should establish the construction site management responsibility according to the scale of the project, the technical complexity and the specific situation of the construction site, and organize the implementation.