How to use liquid raw meal belt? 5. How to use the liquid raw meal belt?

There are instructions on the general product packaging.

Then I'll talk about it.

How to use:1Use a cotton cloth to remove the oil stain from the pipe thread and dry it.

2.Apply a sufficient amount of glue to the pipe thread or the part to be sealed, and then assemble and let stand.

3.Tighten and adjust the angle within 3 minutes after installation, and it should not be adjusted again after curing.

4.The initial curing time at room temperature is 5-30min, and it is completely cured after 24 hours of assembly, which can reach the highest strength.

5.It is used for steel, copper, iron and other metal materials, the ambient temperature is above 25, and the pressure is tested after four hours of installation; temperature at 15-25, 8 hours; 0 15, 16 hours. The curing time with stainless steel, aluminum, and alloy should be doubled.

Notes:1The oil stain on the thread should be wiped before gluing, otherwise the curing effect will be affected.

2.It cannot be used for sealing pure oxygen and strong oxidizing agent media.

3.The disassembly strength is moderate, the pipe below DN50 is disassembled with a pipe wrench, and when the disassembly strength of the pipe above DN50 is large, it can be heated and disassembled with a spray gun.

4.The product is non-toxic, but hands should be cleaned when work is done.

5.The glue is applied to the tube teeth, and the glue is evenly applied with a brush, which can reduce the amount of glue used and prevent the glue from being suspended on the screw teeth.

6.Prevent excessive force from causing the previously installed and curing joints to rotate with you.

7.It can be reused, and the residual glue of the joint needs to be removed with a wire brush after disassembly, and the glue can be reapplied.

8.It is not suitable for pipe thread sealing and locking above 150 high temperature working conditions.

The liquid raw meal tape is that you apply the liquid glue to the tube in a circle, and then tighten it for a few minutes and the liquid raw material tape will solidify.

AbstractYes, after wiping the pipe dry, use a liquid raw meal tape. Precautions for the use of liquid raw meal belts:

1. Metal, oil and sundries shall not be mixed into the bottle.

2. The pipe thread above DN65 must be glued on both sides inside and outside, otherwise some joints may leak.

3. The glue extruded from the tooth will not solidify for a long time due to contact with oxygen.

4. If it is not easy to disassemble with a pipe wrench. It can be disassembled with a gas spray gun.

Can you use liquid raw meal belt if there is water in the pipe?

Yes, wipe the pipes dry and use a liquid raw meal tape. Precautions for the use of liquid raw meal belt: 1. Metal, oil and sundries shall not be mixed into the bottle.

2. The pipe thread above DN65 must be glued on both sides inside and outside, otherwise some joints may leak. 3. The glue extruded from the tooth will not solidify for a long time due to contact with oxygen. 4. If it is not easy to disassemble with a pipe wrench.

It can be disassembled with a gas spray gun.

If the water doesn't dry up, it can't work.

It's better to dry it, but now I can't do it for a while, I can wait a few days to see if it can evaporate and dry naturally.

Generally, it is about 1-2 days, the summer time will be slightly shorter, and the winter time will be relatively longer, and there will be a detailed description on the outside of the jar. Liquid raw tape is anaerobic glue, which is a chemical substance that is mainly used for sealing metal thread gaps.

When using the liquid raw material belt, the oil stain on the thread should be wiped clean so as not to affect the curing effect.

Because liquid raw meal tape is a chemical substance, it should be avoided from direct contact with the body and precautions should be taken when using it.

After installation, water can be supplied 24 hours in summer and 48 hours in winter. Liquid raw meal belt, starting in the 40s of the 20th century, in 1953 the United States research methacrylate polyethylene glycol biesters found the curing characteristics of acrylates, and later through the study of adding peroxide and other additives, made of practical value of the glue, at present, has been widely used in aviation, military industry, general machinery, transportation machinery, oilfield pipelines, industrial pipelines and civil pipelines, mold manufacturing, etc. <

After installation, water can be supplied 24 hours in summer and 48 hours in winter. Liquid raw meal belt, starting in the 40s of the 20th century, in 1953 the United States research methacrylate polyethylene glycol biesters found the curing characteristics of acrylates, and later through the study of adding peroxide and other additives, made of practical value of the glue, at present, has been widely used in aviation, military industry, general machinery, transportation machinery, oilfield pipelines, industrial pipelines and civil pipelines, mold manufacturing, etc.

After installation, water can be supplied 24 hours in summer and 48 hours in winter. Liquid raw meal belt, starting in the 40s of the 20th century, in 1953 the United States research methacrylate polyethylene glycol biesters found the curing characteristics of acrylates, and later through the study of adding peroxide and other additives, made of practical value of the glue, at present, has been widely used in aviation, military industry, general machinery, transportation machinery, oilfield pipelines, industrial pipelines and civil pipelines, mold manufacturing, etc.

How to use: 1. Remove the oil stain of the pipe thread and dry it.

2. Coat a sufficient amount of glue on the pipe thread, then assemble and stand.

3. Tighten and adjust the angle within 3 minutes after installation, and it should not be adjusted again after curing.

4. It is used for steel, copper and iron pipes, the ambient temperature is above 25, and the pressure can be tested after 24 hours of installation; It should be used for stainless steel, aluminum, and alloy steel for twice the time.

Liquid raw meal belts can be used on domestic water pipes. But pay attention to the method of operation. This is because the curing of the liquid raw meal belt requires isolation of oxygen and contact with metal parts.

Therefore, when gluing, only the outer thread is applied, and the 2 rings at the very edge are not glued to ensure that the glue solidifies in the thread gap and does not flow into the inner wall of the pipe. <

Liquid raw meal belts can be used on domestic water pipes. But pay attention to the method of operation. This is because the curing of the liquid raw meal belt requires isolation of oxygen and contact with metal parts.

Therefore, when gluing, only the outer thread is applied, and the 2 rings at the very edge are not glued to ensure that the glue solidifies in the thread gap and does not flow into the inner wall of the pipe.

Kiss! Hello, happy to answer your <>

Adding a layer of liquid material belt on top of the raw material belt can play a role in sealing the burning of the green material, and the mixing of liquid raw material belt and raw material belt also has the effect of sealing, but there will be no superimposed effect. Raw meal with liquid and solid two, in addition to the difference in form, the two kinds of raw meal belt in the composition, use method, sealing effect convenience also exist there are certain differences, in comparison, although the sealing effect of the solid raw meal belt is slightly inferior, but the storage is more convenient, do not know the need for curing time, the dosage is well controlled, which is better mainly depends on the actual construction situation. Generally speaking, the liquid raw meal belt is not used together with the ordinary raw material belt, because it will not play a better sealing effect, but a waste of resources, the liquid raw material belt replaces the solid raw material belt, and the liquid raw meal in the pipeline thread sealant has the characteristics of high bonding strength, good sealing, corrosion resistance, high temperature resistance, aging resistance, etc.

The precision filtration unit, which is quick to install, is the most advanced thread sealant available. It is widely used in fire protection, shipbuilding, natural gas, tap water, wheel and instrument system, air conditioning, air pipe, oil pipe, hydraulic pipe and other industrial and civil pipeline thread sealing and locking. After mixing with raw material tape, I can't do any better sealing use, I hope mine can help you <>

Do you have any other questions?