How do you manually remove the Hyundai Sonata tire pressure monitoring light when it is on?

Modern SonataTire pressure monitoringThe light came on and lifted it

1. Press the brake pedal of the car firmly and prepare to turn on the power supply of the whole car.

2. Press the car's one-button start button.

3. The instrument lights up, and the power supply of the whole car is turned on.

4. Inflate the four tires of the vehicle to the standard air pressure.

5. Press the elimination button of the vehicle's tire pressure warning light for 3 seconds.

1. After the tire pressure indicator light of the eighth-generation Sonata of Beijing Hyundai is lit, there is no button for manual reset, and it will automatically turn off after driving the car for a certain distance.

2. Specifically, as long as the speed is greater than 20km h during driving and more than 4 minutes of continuous driving, it can be automatically extinguished.

3. The independent tire pressure monitoring system of Suoba is designed as follows: if the tire pressure is 25% lower than the specified tire pressure in one of the four tires, the system will light up the warning light to remind the driver and inflate the tire in time.

If you drive at a speed of 40 or more for 1 or 2 minutes, it will disappear automatically.

Flashing and shining: The main reason is that the data of the tire pressure monitoring computer and the tire pressure sensor are lost, and the computer needs to be matched.

When emergency avoidance, ESP intervenes to increase the rotational force of the driving wheel; When there is a tendency to flick, the ESP brakes the other wheel to reduce rotation, helping the vehicle to comply with the driver's steering intention.

Hello, I am helping you to inquire about the relevant information and will reply to you immediately.

The tire pressure failure light is usually caused by the following conditions: 1. The tire is punctured; 2. The tire pressure is too high; 3. The driving time of low tire pressure is too long; 4. The tire pressure that has not been inflated for a long time becomes low. So what to do when the tire pressure light comes on?

How to eliminate the tire pressure light? We can do this as follows. 1. Drive slowly, find a safe place to stop, then turn off the engine, start the vehicle again after 1-2 minutes, wait for the vehicle to run stably and check the tire pressure value displayed on the dashboard; 2. Insufficient tire pressure or high tire pressure may cause the tire pressure light to light up, we can slowly drive the car to the car repair shop or beauty shop to adjust the tire pressure, if there is a self-contained inflation device can be adjusted in situ; 3. In the process of inflating or deflating the tire pressure, observe the display of the tire pressure light on the dashboard of your vehicle, and wait for the tire pressure light to go out to remind you to stop inflating, and if you charge too much, release the excess gas (in the case of two people); 4. If the tire pressure light still does not go out after adjustment, it means that it needs to be turned off manually, and the setting button can be found in the central control instrument panel of the car to reset the tire pressure, usually by pressing the set button; 5. If the vehicle does not support manual operation, let the maintenance personnel use a special decoder to clear the fault code under the condition of ensuring that the tire pressure is normal.

The eighth-generation Sonata tire pressure reset method:

1. The tire pressure monitoring function on the on-board intelligent system is only set when the vehicle is stopped;

2. Turn on the ignition switch, enter the instrument cluster menu through the steering column switch or the switch button on the multi-function steering wheel, select "Comfort System Settings", and click the "Tire Pressure" option;

3. Select "Pressure Monitoring", at this time, the instrument displays the tire pressure monitoring status, we select the storage wheel pressure in the settings, and click to confirm;

4. After the inflation pressure is stored, the tire pressure is set and the alarm light is extinguished;

5. The operation method of tire pressure monitoring reset is: turn on the start ignition switch, press and hold the tire pressure monitoring reset button, and let go after hearing the sound of "knock", at this time, the tire pressure monitoring system will store the normal tire pressure data at this time, and then automatically clear the original data, and finally the fault light of the dashboard is extinguished. This method is only available on certain vehicle models, as described in the vehicle's owner's manual.

This can be reset directly in the car operating system. Select the car operating system in the center of the car, drag it to the back and you can see that there is a maintenance and maintenance. Go in and select the tire pressure mode, then click Save Data so you can reset it.

Press the tire pressure monitoring button for two seconds, hear the sound of "dang", the tire pressure monitoring warning light will go off, and the initialization of tire pressure monitoring will be completed after two or three kilometers of driving.

It's very convenient to go to 4s to clear.

It's simple to have a manual lift tool;

The specific operation steps for resetting the tire pressure light of the car are as follows:

1. Press the brake pedal of the car to prepare for the power supply of the whole car.

2. Press the car's one-button start button.

3. The dashboard of the car lights up, which proves that the power supply of the whole car is turned on.

4. Inflate the four wheels of the car to standard air pressure.

5. Press and hold the tire pressure reset button located on the vehicle operation panel for more than 3 seconds to complete the operation.

Turn on the power of the meter and press and hold the reset button until the tire pressure warning light goes out. Press and hold the reset button again until the tire pressure is low and the warning light flashes three times and goes out. After 15 minutes of driving at a speed of 30 km/h, the initial completion returned to normal.

If the above operation is completed and the alarm is still not eliminated, consider the tire pressure sensor failure. Generally, after it is broken, it will become a straight line in the case of the original value, and there is no value display. It's not all bad. If the values are not displayed, it may be a receiver problem, and the receiver should be replaced.

Precautions before adjusting the tire pressure.

1. Adjust the tire pressure based on the principle of the tire pressure standard that comes with the car, and adjust it on some basis.

2. The tire pressure between cool tires and hot tires is different, and the difference between the two is about 0 3bar。The tyre pressure standard refers to the cold tyre pressure, i.e. at least three hours after stopping or when the tyre has traveled no more than 2 km.

3. The maximum inflatable air pressure of the car tire should not exceed the "maximum safe inflatable air pressure" marked on the tire.

Hello, the tire pressure light is on, indicating that the tire pressure is insufficient, you can check the replenishment of enough, the general car with the tire pressure reset button can be reset or some cars can be eliminated after a period of time

This is not necessarily, it depends on the specific model, some different models, the way to eliminate the fault light is different.

The tire pressure warning light is on and the yellow light is always on, how to press reset?

Modern SonataTire pressure monitoringThe light came on and lifted it

1. Press the brake pedal of the car firmly and prepare to turn on the power supply of the whole car.

2. Press the car's one-button start button.

3. The instrument lights up, and the power supply of the whole car is turned on.

4. Inflate the four tires of the vehicle to the standard air pressure.

5. Press the vehicle's tire pressure warning bureau leakage light to eliminate the Zhengzhou button for 3 seconds to shout the wax mask.

1. Reduce tire pressure.

2. Press and hold the tire pressure button for more than 30 seconds, and the system will reset and set the new tire parameters to the default value. Note that this method is used in the case of a false alarm of the tire pressure warning light, such as when the car is driving on sand or ice and snow, and if a wheel slips, the system will consider the tire pressure abnormal.

3. The tire puncture will also cause the tire pressure warning light to light up, in which case it is necessary to repair or replace the new tire.

4. Tire failure will also cause the tire pressure warning light to light up, in this case, you need to inflate the tire.

How to reset the tire pressure warning light when it is on.

Tire pressure fault light: There are several ways: 1. Re-set the fault light to eliminate it.

2. Press the set button with tire pressure identification on the far right side of the front of the gear lever for a long time, if the tire pressure is normal, the alarm light can be eliminated. 3. You can press and hold the tire pressure monitoring button until the light goes out, so that it is eliminated and then press the tire pressure monitoring button until the light is on, so that it is set again. 4. It can be eliminated by setting it in the multi-function steering wheel.

Or use a computerized detector to reset and eliminate. 5. How to turn off the tire pressure indicator: open the glove compartment on the passenger side, there is a button in the upper left corner (next to the auxiliary airbag key switch), in the case of turning on the ignition switch, press and hold the button until the tire pressure light goes out.

However, the tire pressure must be within the normal range. What does it mean when the tire pressure fault light is on? There are two kinds, one is to calculate the wheel circumference, by the wheel speed sensor detection, if the tire pressure of the four tires is inconsistent, too high or too low may alarm, one is the tire pressure sensor directly detected, a single car tire pressure is too low, too high will alarm, it may also be the sensor power drain or damage.

The tire pressure light is on and press the reset method:

1. For models with tire pressure reset buttons, press and hold the tire pressure monitoring reset button;

2. Some models can be set by the tire pressure monitoring function on the central control screen, turn on the start ignition switch and press the tire pressure monitoring reset button, let go after hearing a knock, then the tire pressure monitoring system will store the normal tire pressure data at this time, automatically clear the original data, and finally the fault light of the dashboard goes out.

The dangers of high tire pressure.

1. The friction and adhesion of the tire will be reduced, which will affect the braking effect;

2. Cause the steering wheel to vibrate and deviate, so that the comfort of driving is reduced;

3. Accelerate the local wear of the tread pattern of the tire, so that the life of the tire is reduced;

4. The vibration of the body becomes larger, which will indirectly affect the life of other parts;