How to operate the vacuum oil purifier correctly, how to clean the filter element of the vacuum oil

Connect the inlet and outlet oil circuits, turn on the 380V, connect the safety ground wires, check whether the circuits are safely connected, whether the valves of the oil circuits are opened, and then carry out the operation procedures after preparation. Start the cooling water pump first, check whether the water circulation is normal, and then jog the vacuum pump to make the oil in the vacuum pump run normally, and then make the vacuum pump run continuously. When the vacuum surface reaches the limit, the oil inlet valve can be opened, and when the oil surface is seen in the lower window of the vacuum cylinder, the oil discharge pump switch will be started, and the normal circulation of the oil circuit will be started to drain and filter impurities, and the heater switch will be turned on to volatilize the water in the oil.

If there is more water in the oil, the oil in the vacuum cylinder will increase, at this time, it is necessary to open the air to control the adapted vacuum degree, and close the air release valve after the water decreases and the oil drifts down, so that the vacuum reaches the limit. At this time, we should pay attention to the reaction of each instrument, if the pressure gauge reading is greater than the time, it means that the filter paper in the filter absorbs more impurities, and needs to be replaced with a new filter paper, after the work is completed, refer to the working principle, open the air release valve, so that the vacuum degree reaches the normal atmospheric pressure, and the oil in the cylinder is discharged, and the remaining oil is released from the oil drain plug to prevent it from being mixed into different types of oil during the next use, and pay special attention in winter, put the water in the vacuum pump and the water tank, otherwise the vacuum pump and water storage tank will be frozen. Baoying high-power power equipment factory.

It's quite simple, you ask the manufacturer for a manual, just look at it

Hello, the method is as follows: 1. The cleaning work of the vacuum oil purifier must be carried out in a state of non-operation, first of all, check whether the inlet and outlet pipelines of the oil purifier have been closed, and check whether the power switch has been closed. 2. After confirming that the power switch has been turned off, open the oil release valve and air release valve to let the residual oil in the vacuum filter flow out until the oil is completely clean. 3. Prepare the oil pan containing kerosene in advance, open the filter cover, take out the filter element of the oil purifier and put it in kerosene, soak it for about half an hour, rinse it twice with water and blow dry.

4. Use a brush to brush off all the deposits that can be seen on the filter, and then wipe them off with a rag. 5. Replace the filter element with the filter and tighten the bolts.

Summary. Hello dear and happy to answer your <>

Vacuum oil purifier vacuum pump plus paraffin-based narrow fraction lubricating oil. This is an important performance of vacuum pump oil, because vacuum pumps require a high degree of vacuum, so paraffin-based narrow fraction lubricating oil is generally used, and for diffusion vacuum pumps, silicone oil or other synthetic oils with very low vapor pressure can also be used.

What kind of oil to add to the vacuum pump of the vacuum oil purifier.

Hello dear and happy to answer your <>

Vacuum oil purifier, vacuum pump, Chang Li ridge, paraffin-based narrow fraction, moisturizing, slippery and disturbing oil. This is an important performance of vacuum pump oil, because vacuum pumps require a high degree of vacuum, so paraffin-based narrow fraction lubricating oil is generally used, and for diffusion vacuum pumps, silicone oil or other synthetic oils with very low vapor pressure can also be used.

Kiss Extended Content <>

Due to the high-speed friction between the sliding vane and the pump body, the oil temperature rises, and the oil is easy to oxidize and decompose, especially the diffusion pump is often in a very high temperature environment, which increases the vapor pressure in the system, such as the reduction of the vacuum degree of the branch key, so the vacuum pump oil is required to have good thermal oxidation stability.

Summary. Hello, glad to answer for you! The vacuum mulberry in the vacuum oil purifier needs to add a certain amount of vacuum poly oil.

The main function of vacuum poly oil is lubrication and sealing, which can reduce friction and wear, and improve the efficiency of vacuum pumps. Different types of vacuum pumps require different types of vacuum polyester, so it is necessary to confirm the type and model of the vacuum pump and consult the relevant instructions before filling the vacuum oil.

Hello, glad to answer for you! The vacuum mulberry in the vacuum oil purifier needs to add a certain amount of vacuum poly oil. The main function of vacuum poly oil is lubrication and sealing, which can reduce friction and wear, and improve the efficiency of vacuum pumps.

Different types of vacuum pumps require different types of vacuum polyester, so it is necessary to confirm the type and model of the vacuum pump and consult the relevant instructions before filling the vacuum oil.

It should be noted that before filling the vacuum poly oil, the vacuum poly should be inspected and maintained to confirm that all parts of the vacuum mulberry are in normal working condition, so as to avoid damage to the vacuum pump due to poor oil quality or improper operation. At the same time, in order to ensure the safety of the operator, attention should be paid to protective measures when filling vacuum oil to avoid splashing out of mountain oil products or touching **, eyes and other parts.

The uses of the vacuum oil purifier are:

1. It can be used for on-site oil filtration and oil replenishment for various oil-immersed transformers, oil-immersed current-voltage transformers and high-voltage oil-less circuit breakers.

2. It can be used for on-site hot oil circulation drying of the above-mentioned equipment, especially for on-site hot oil circulation drying of oil immersion current, voltage transformer and high-voltage oil-less circuit breaker.

Features:

1. Small size and light weight.

2. The vacuum oil feed is used to install a tubular rotary injector, which reduces the resistance, accelerates the rotation speed, and increases the effect of oil and gas separation.

3. The function of metamorphic oil regeneration and purification is added, the silica gel oil purification system is added, and the silica gel oil purification and impurity filtration are integrated, and the impurities are filtered out for the mildly deteriorated transformer oil, and then the adsorption and regeneration of the silica gel oil purifier make it meet the qualified oil standard.

4. There are two filtration methods for the oil purifier part: one is the traditional oil filtration method - filter paper as the filter medium; Another method is to use a special fine filter cartridge that does not require filter paper as the oil filter medium.

A: This method allows the oil to filter out trace amounts of water and gases from the oil at a high vacuum and not too high a temperature. When the hot oil passes through the spray tube of the vacuum tank and sprays very fine droplets, the water (including gas) in the oil is pumped out by negative pressure due to evaporation in the vacuum state, and the oil droplets fall and return to the lower oil chamber to be discharged by the oil pump.

Summary. Hello <>

If the vacuum pump of the oil purifier is filled with oil, the following measures can be taken to solve the problem:1Stop using the oil purifier and cut off the power supply to prevent further damage to the equipment or malfunction.

2.Check whether the oil pipes and connections of the oil purifier are loose or damaged, and repair or replace them in time if necessary. 3.

Clean the oil pipe of the oil purifier and remove foreign matter or dirt from the oil pipe to ensure that it is unobstructed. 4.Check whether the oil pump of the oil purifier is working properly, if there is a fault that needs to be repaired or replaced.

What should I do if the vacuum pump of the oil purifier feeds oil.

Hello <>

If the vacuum pump of the oil purifier is filled with oil, the following measures can be taken to solve the problem:1Stop using the oil purifier and cut off the power supply to prevent further damage to the equipment or malfunction.

2.Check whether the oil pipes and connections of the oil purifier are loose or damaged, and repair or replace them in time if necessary. 3.

Clean the oil pipe of the oil purifier and remove foreign matter or dirt from the oil pipe to ensure that it is unobstructed. 4.Check whether the oil filter pump is working properly, and if there is a fault, it needs to be repaired or replaced.

If the oil pipe and the connecting parts are normal, but the vacuum pump still has oil inflow, it is caused by damage to the seals inside the vacuum pump. At this point, the vacuum pump needs to be dismantled for repair or seals replaced. <>